iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E543-06

(Practice)

Standard Specification for Agencies Performing Nondestructive Testing

Standard Specification for Agencies Performing Nondestructive Testing

SCOPE
1.1 This specification covers minimum requirements for agencies performing nondestructive testing (NDT).
1.2 When using this specification to assess the capability of, or to accredit NDT agencies, Guide E 1359 shall be used as a basis for the survey. It can be supplemented as necessary with more detail in order to meet the auditor's specific needs.
1.3 This specification can be used as a basis to evaluate testing or inspection agencies, or both, and is intended for use for the qualifying or accrediting, or both, of testing or inspection agencies, public or private.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
28-Feb-2006
ICS
03.120.10 - Quality management and quality assurance
19.100 - Non-destructive testing
Technical Committee
E07 - Nondestructive Testing
Drafting Committee
E07.09 - Nondestructive Testing Agencies
Current Stage
Ref Project

Relations

Replaces
ASTM E543-04 - Standard Practice for Agencies Performing Nondestructive Testing
Effective Date
01-Mar-2006
Replaced By
ASTM E543-08 - Standard Specification for Agencies Performing Nondestructive Testing
Effective Date
15-Feb-2008
Referred By
ASTM E569/E569M-20 - Standard Practice for Acoustic Emission Monitoring of Structures During Controlled Stimulation
Effective Date
01-Mar-2006
Referred By
ASTM E2698-18e1 - Standard Practice for Radiographic Examination Using Digital Detector Arrays
Effective Date
01-Mar-2006
Referred By
ASTM E1359-17 - Standard Guide for Auditing and Evaluating Capabilities of Nondestructive Testing Agencies
Effective Date
01-Mar-2006
Referred By
ASTM E709-21 - Standard Guide for Magnetic Particle Testing
Effective Date
01-Mar-2006
Referred By
ASTM E2533-21 - Standard Guide for Nondestructive Examination of Polymer Matrix Composites Used in Aerospace Applications
Effective Date
01-Mar-2006
Referred By
ASTM E1416-23 - Standard Practice for Radioscopic Examination of Weldments
Effective Date
01-Mar-2006
Referred By
ASTM E1219-21 - Standard Practice for Fluorescent Liquid Penetrant Testing Using the Solvent-Removable Process
Effective Date
01-Mar-2006
Referred By
ASTM F2959-23a - Standard Practice for Aerial Adventure Courses
Effective Date
01-Mar-2006
Referred By
ASTM E3052-21 - Standard Practice for Examination of Carbon Steel Welds Using An Eddy Current Array
Effective Date
01-Mar-2006
Referred By
ASTM E3102-18 - Standard Practice for Microwave Examination of Polyethylene Electrofusion Joints Used in Piping Application
Effective Date
01-Mar-2006
Referred By
ASTM E1817-08(2022) - Standard Practice for Controlling Quality of Radiological Examination by Using Representative Quality Indicators (RQIs)
Effective Date
01-Mar-2006
Referred By
ASTM E3375-23 - Standard Practice for Cone Beam Computed Tomographic (CT) Examination
Effective Date
01-Mar-2006
Referred By
ASTM E2661/E2661M-20e1 - Standard Practice for Acoustic Emission Examination of Plate-like and Flat Panel Composite Structures Used in Aerospace Applications
Effective Date
01-Mar-2006

Buy Standard

ASTM E543-06 - Standard Specification for Agencies Performing Nondestructive TestingASTM E543-06 - Standard Specification for Agencies Performing Nondestructive Testing
PreviousNext
Standard
ASTM E543-06 - Standard Specification for Agencies Performing Nondestructive Testing
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E 543 – 06
Standard Specification for
1
Agencies Performing Nondestructive Testing
This standard is issued under the fixed designation E 543; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This specification has been approved for use by agencies of the Department of Defense.
1. Scope E 214 Practice for Immersed Ultrasonic Testing by the
Reflection Method Using Pulsed Longitudinal Waves
1.1 This specification covers minimum requirements for
E 215 Practice for Standardizing Equipment for Electro-
agencies performing nondestructive testing (NDT).
magnetic Examination of SeamlessAluminum-Alloy Tube
1.2 When using this specification to assess the capability of,
E 243 Practice for Electromagnetic (Eddy-Current) Exami-
or to accredit NDT agencies, Guide E 1359 shall be used as a
nation of Copper and Copper-Alloy Tubes
basis for the survey. It can be supplemented as necessary with
E 273 Practice for Ultrasonic Examination of the Weld
more detail in order to meet the auditor’s specific needs.
Zone of Welded Pipe and Tubing
1.3 This specification can be used as a basis to evaluate
E 309 Practice for Eddy-Current Examination of Steel Tu-
testing or inspection agencies, or both, and is intended for use
bular Products Using Magnetic Saturation
for the qualifying or accrediting, or both, of testing or
E 317 Practice for Evaluating Performance Characteristics
inspection agencies, public or private.
of Ultrasonic Pulse-Echo Examination Instruments and
1.4 This standard does not purport to address all of the
Systems without the Use of Electronic Measurement In-
safety concerns, if any, associated with its use. It is the
struments
responsibility of the user of this standard to establish appro-
E 376 Practice for Measuring Coating Thickness by
priate safety and health practices and determine the applica-
Magnetic-FieldorEddy-Current(Electromagnetic)Exami-
bility of regulatory limitations prior to use.
nation Methods
2. Referenced Documents E 426 Practice for Electromagnetic (Eddy-Current) Exami-
2
nation of Seamless and Welded Tubular Products, Austen-
2.1 ASTM Standards:
itic Stainless Steel and Similar Alloys
E94 Guide for Radiographic Examination
E 427 Practice for Testing for Leaks Using the Halogen
E114 Practice for Ultrasonic Pulse-Echo Straight-Beam
Leak Detector(Alkali-Ion Diode)
Examination by the Contact Method
E 428 Practice for Fabrication and Control of Metal, Other
E 125 Reference Photographs for Magnetic Particle Indica-
than Aluminum Reference, Blocks Used in Ultrasonic
tions on Ferrous Castings
Examination
E 127 Practice for Fabricating and Checking Aluminum
E 431 Guide to Interpretation of Radiographs of Semicon-
Alloy Ultrasonic Standard Reference Blocks
ductors and Related Devices
E 164 PracticeforUltrasonicContactExaminationofWeld-
E 432 Guide for Selection of a Leak Testing Method
ments
E 433 Reference Photographs for Liquid Penetrant Inspec-
E 165 Test Method for Liquid Penetrant Examination
tion
E 213 Practice for Ultrasonic Examination of Metal Pipe
E 479 Guide for Preparation of a LeakTesting Specification
and Tubing
E 493 TestMethodsforLeaksUsingtheMassSpectrometer
Leak Detector in the Inside-Out Testing Mode
E 494 Practice for Measuring Ultrasonic Velocity in Mate-
1
This specification is under the jurisdiction of ASTM Committee E07 on
rials
Nondestructive Testing and is the direct responsibility of Subcommittee E07.09 on
E 498 TestMethodsforLeaksUsingtheMassSpectrometer
Nondestructive Testing Agencies.
Leak Detector or Residual Gas Analyzer in the Tracer
Current edition approved March 1, 2006. Published March 2006. Originally
approved in 1976. Last previous edition approved in 2004 as E 543 - 04.
Probe Mode
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
E 499 TestMethodsforLeaksUsingtheMassSpectrometer
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Leak Detector in the Detector Probe Mode
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E543–06
E 515 Test Method for Leaks Using Bubble EmissionTech- E 1025 Practice for Design, Manufacture, and Material
niques Grouping Classification of Hole-Type Image Quality Indi-
cators (IQI) Used for Radiology
E 545 TestMethodforDeterminingImageQualityinDirect
E 1030 Test Method for Radiographic Examination of Me-
Thermal Neutron Radiographic Examination
tallic Castings
E 56
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E543-21(Specification)
Standard Specification for Agencies Performing Nondestructive Testing

ABSTRACT
This specification covers the minimum requirements for agencies performing nondestructive testing. It can also be used as a basis to evaluate testing or inspection agencies, or both that are intended for use in qualifying or accrediting, or both of testing or inspection agencies that are either public or private. A nondestructive testing agency's capabilities shall include, but not limited to, one or more of the following methods: magnetic particle, penetrant, radiographic/fluoroscopic, ultrasonic, eddy current, and leak testing. Minimum requirements include: a written Procedures Manual for the type of work for which the agency is contracted; process control or operation procedures that shall contain the information necessary to control the various activities necessary for materials examination; personnel qualification which include procedures for training, certification, and recertification; equipment maintenance and calibration which shall contain inventory listings; equipment operation and technique file; and records and documentation that shall be maintained in a central file and in other accessible files as necessary and shall be available for authority examination.
SCOPE
1.1 This specification covers minimum requirements for agencies performing nondestructive testing (NDT).  
1.2 When using this specification to assess the capability of, or to accredit NDT agencies, Guide E1359, Specification E329, ISO 9001, ISO 17025, or ISO 17020 may be used as a basis for the survey. It can be supplemented as necessary with more detail in order to meet the auditor's specific needs.  
1.3 This specification can be used as a basis to evaluate testing or inspection agencies, or both, and is intended for use for the qualifying or accrediting, or both, of testing or inspection agencies, public or private.  
1.4 Units—The use of SI or inch-pound units, or combination thereof, will be the responsibility of the technical committee whose standards are referred to in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    14 pages
    English language
    sale 15% off
  • Technical specification
    14 pages
    English language
    sale 15% off
ASTM
ASTM E543-21(Specification)
Standard Specification for Agencies Performing Nondestructive Testing

ABSTRACT
This specification covers the minimum requirements for agencies performing nondestructive testing. It can also be used as a basis to evaluate testing or inspection agencies, or both that are intended for use in qualifying or accrediting, or both of testing or inspection agencies that are either public or private. A nondestructive testing agency's capabilities shall include, but not limited to, one or more of the following methods: magnetic particle, penetrant, radiographic/fluoroscopic, ultrasonic, eddy current, and leak testing. Minimum requirements include: a written Procedures Manual for the type of work for which the agency is contracted; process control or operation procedures that shall contain the information necessary to control the various activities necessary for materials examination; personnel qualification which include procedures for training, certification, and recertification; equipment maintenance and calibration which shall contain inventory listings; equipment operation and technique file; and records and documentation that shall be maintained in a central file and in other accessible files as necessary and shall be available for authority examination.
SCOPE
1.1 This specification covers minimum requirements for agencies performing nondestructive testing (NDT).  
1.2 When using this specification to assess the capability of, or to accredit NDT agencies, Guide E1359, Specification E329, ISO 9001, ISO 17025, or ISO 17020 may be used as a basis for the survey. It can be supplemented as necessary with more detail in order to meet the auditor's specific needs.  
1.3 This specification can be used as a basis to evaluate testing or inspection agencies, or both, and is intended for use for the qualifying or accrediting, or both, of testing or inspection agencies, public or private.  
1.4 Units—The use of SI or inch-pound units, or combination thereof, will be the responsibility of the technical committee whose standards are referred to in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    14 pages
    English language
    sale 15% off
  • Technical specification
    14 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6390-23(Test Method)
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

SIGNIFICANCE AND USE
5.1 This test method can be used to determine whether the amount of draindown measured for a given asphalt mixture is within specified acceptable levels. The test provides an evaluation of the draindown potential of an asphalt mixture during mixture design and/or during field production. This test is primarily used for mixtures with high coarse aggregate content such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the amount of draindown in an uncompacted asphalt mixture sample when the sample is held at elevated temperatures comparable to those encountered during the production, storage, transport, and placement of the mixture. The test is particularly applicable to mixtures such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM B472-23(Specification)
Standard Specification for Nickel Alloy Billets and Bars for Reforging

ABSTRACT
This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R30556 nickel alloy billets and bars for reforging. The products shall be hot worked from ingots by rolling, forging, extruding, hammering, or pressing. The material shall conform to the chemical composition requirements prescribed by the reference material. The chemical composition of the material shall be determined by chemical analysis in accordance with test method E1473.
SCOPE
1.1 This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N10362, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, UNS N06699, and UNS R305562 billets and bars for reforging.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off