ASTM D6244-06(2018)
(Test Method)Standard Test Method for Vertical Compression of Geocomposite Pavement Panel Drains
Standard Test Method for Vertical Compression of Geocomposite Pavement Panel Drains
SIGNIFICANCE AND USE
5.1 The vertical compression test for geocomposite pavement panel drains is intended to simulate vertical, horizontal, and eccentric loading resulting from an applied vertical load. The results of the analyses, including vertical strain of the panels and core area change, may be used as an index test. The vertical compression test may be used to evaluate core area change for a given load.
5.2 The vertical compression test may be used to evaluate percent vertical strain for a given load.
5.3 This test method may be modified to evaluate core area change and vertical strain under various backfill conditions.
SCOPE
1.1 This test method covers vertical strain and core area change of geocomposite pavement drains, such as those included in Specification D7001, under vertical compression.
1.2 The values as stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D6244 − 06 (Reapproved 2018)
Standard Test Method for
Vertical Compression of Geocomposite Pavement Panel
Drains
This standard is issued under the fixed designation D6244; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.2 compressive strain, n—the ratio of compressive defor-
mation to the gage length of the test specimen, expressed as a
1.1 This test method covers vertical strain and core area
dimensionless ratio (new).
change of geocomposite pavement drains, such as those
3.1.3 gage length, n—the known distance between two
included in Specification D7001, under vertical compression.
benchmarks (see Terminology D1566).
1.2 The values as stated in SI units are to be regarded as the
3.1.3.1 Discussion—In compression testing of
standard. The values given in parentheses are for information
geosynthetics, gage length is the measured thickness of the test
only.
specimen under specified compressional force, expressed in
1.3 This standard does not purport to address all of the
units of length.
safety concerns, if any, associated with its use. It is the
3.1.4 geosynthetic, n—a planar product manufactured from
responsibility of the user of this standard to establish appro-
polymeric material used with foundation, soil, rock, earth, or
priate safety, health, and environmental practices and deter-
any other geotechnical engineering-related materials as an
mine the applicability of regulatory limitations prior to use.
integral part of a manmade project, structure, or system (see
1.4 This international standard was developed in accor-
Terminology D4439).
dance with internationally recognized principles on standard-
3.1.5 index test, n—a test procedure which may contain a
ization established in the Decision on Principles for the
known bias but which may be used to order a set of specimens
Development of International Standards, Guides and Recom-
with respect to the property of interest (see Terminology
mendations issued by the World Trade Organization Technical
D4439).
Barriers to Trade (TBT) Committee.
4. Summary of Test Method
2. Referenced Documents
4.1 Geocomposite pavement edge drains are placed into a
2.1 ASTM Standards:
304.8-mm (12-in.) long, 106.7-mm (4.20-in.) wide, and
D1566 Terminology Relating to Rubber
610-mm (24-in.) tall glass and aluminum compression cham-
D4354 Practice for Sampling of Geosynthetics and Rolled
ber. The geocomposites are placed against the wall of the
Erosion Control Products (RECPs) for Testing
chamber. The remainder of the chamber is then backfilled with
D4439 Terminology for Geosynthetics
a specified sand. A vertical load is applied at a constant rate.
D7001 Specification for Geocomposites for Pavement Edge
The vertical strains of the panels and change in core area and
Drains and Other High-Flow Applications
height is recorded at 1112.5-N (250-lb) increments. The test is
3. Terminology
discontinued at 4450 N (1000 lb) or 156.5 kPa (22.7 psi). The
change in vertical strain, core height, and core area is deter-
3.1 Definitions of Terms Specific to This Standard:
mined.
3.1.1 compressive deformation, n—the decrease in gage
length produced in the test specimen by a compressive load,
5. Significance and Use
expressed in units of length (new).
5.1 The vertical compression test for geocomposite pave-
ment panel drains is intended to simulate vertical, horizontal,
This test method is under the jurisdiction of ASTM Committee D35 on
and eccentric loading resulting from an applied vertical load.
Geosynthetics and is the direct responsibility of Subcommittee D35.01 on Mechani-
cal Properties.
The results of the analyses, including vertical strain of the
Current edition approved Feb. 1, 2018. Published February 2018. Originally
panels and core area change, may be used as an index test. The
approved in 1998. Last previous edition approved in 2011 as D6244 – 06 (2011).
vertical compression test may be used to evaluate core area
DOI: 10.1520/D6244-06R18.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or change for a given load.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
5.2 The vertical compression test may be used to evaluate
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. percent vertical strain for a given load.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D6244 − 06 (2018)
5.3 This test method may be modified to evaluate core area machine must be capable of loading at a rate of 445 N
change and vertical strain under various backfill conditions. (100 lb)⁄min, and maintaining a constant load for an indefinite
period.
6. Apparatus
6.2 Compression Box—The box must be capable of holding
6.1 Compression Machine—A compression machine that is the specimen and the backfill material, and it must be capable
capable of producing at least 4450 N (1000 lb) of load. The of supporting a minimum vertical load of 4450 N (1000 lb).
FIG. 1 Edge Drain Compression Chamber
D6244 − 06 (2018)
TABLE 1 Backfill Gradation
The design of the box and the loading plate shall conform to
A
Fig. 1. The box shall be rigid enough to resist deformation. Sieve Size Percent Passing
9.5mm( ⁄8 in.) 100
6.3 Clear Plastic Spacers (Shown and Described in Fig.
No. 4 90 – 100
2)—These spacers are used to protect the tempered glass ends
No. 16 45 – 80
No. 50 5 – 25
of the compression box from scratches.
No. 100 0 – 8
6.4 Sand—Sufficient sand to fill the compression box. Natu-
A
Crushed sand may be accepted with a minimum sand equivalent of 70, provided
ral sand is recommended. The sand shall have a gradation
the passing No. 40 sieve fraction of the sand is nonplastic.
conformingtoTable1.Thesandshallbeovendriedandcooled
to room temperature.
6.5 Tracing Paper—The paper must be suitable for tracing
and have a minimum size of 220 by 508 mm (8.5 by 20 in.).
6.7 Planimeter—Theplanimeterisusedtodetermineareato
6.6 Light Source—Any high-intensity point light source is calculate loss of core area at the various load increments (a
acceptable (for example, a large mag light). minimum of a digital planimeter should be used to calculate
FIG. 2 Top View of Compression Chamber
D6244 − 06 (2018)
core area). If computer digitizing equipment or scanning shall be oriented in the chamber in the same manner as
equipment is available, this may be used in lieu of the recommended by the manufacturer to be placed in the field,
planimeter. with the inside walls of the chamber being considered, first, the
pavement side of the trench, and second, the shoulder side of
6.8 Scale (Length Measuring Device)—A minimum range
thetrench.Thesampleshallbeplacedintothechamberinsuch
of 450 mm (18 in.), and an accuracy of 1 mm ( ⁄16 in.).
a way that the maximum core area of the panel is visible
through the ends of the box. If necessary, the samples shall be
7. Sampling
snugged into place with thin panes of plexiglass; 3.2 mm
7.1 Lot Sample—Divide the product into lots and take the
(0.125 in.) and 6.4 mm (0.25 in.) are recommended, to ensure
lot sample as directed in Practice D4354.
proper tightness on the walls of the chamber.
7.2 Laboratory Sample—Consider the units in the lot
NOTE 5—The panes shall not be forced into place. This could cause
sample as the units in the laboratory sample for the lot to be
compression or misalignment in the sample.
tested.Takeforalaboratorysampleasampleextendingthefull
9.3 The 19-mm ( ⁄4-in.) excess geotextile at the ends of the
width of the geocomposite edge drain, of sufficient length so
core shall be lapped as shown in Fig. 2. This helps to prevent
that the requirements in 7.3 are met.
sand from flowing between the end of the core and the glass
NOTE 1—Thi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.