ASTM E1316-17a
(Terminology)Standard Terminology for Nondestructive Examinations
Standard Terminology for Nondestructive Examinations
SIGNIFICANCE AND USE
3.1 The terms found in this standard are intended to be used uniformly and consistently in all nondestructive testing standards. The purpose of this standard is to promote a clear understanding and interpretation of the NDT standards in which they are used.
SCOPE
1.1 This standard defines the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle testing, neutron radiology and gauging, ultrasonic testing, and other technical methods.
1.2 Committee E07 recognizes that the terms examination, testing and inspection are commonly used as synonyms in nondestructive testing. For uniformity and consistency in E07 nondestructive testing standards, Committee E07 encourages the use of the term examination and its derivatives when describing the application of nondestructive test methods. There are, however, appropriate exceptions when the term test and its derivatives may be used to describe the application of a nondestructive test, such as measurements which produce a numeric result (for example, when using the leak testing method to perform a leak test on a component, or an ultrasonic measurement of velocity). Additionally, the term test should be used when referring to the NDT method, that is, Radiologic Testing (RT), Ultrasonic Testing (UT), and so forth. (Example: Radiologic Testing (RT) is often used to examine material to detect internal discontinuities.)
1.3 Section A defines terms that are common to multiple NDT methods, whereas, the subsequent sections define terms pertaining to specific NDT methods.
1.4 As shown on the chart below, when nondestructive testing produces an indication, the indication is subject to interpretation as false, nonrelevant or relevant. If it has been interpreted as relevant, the necessary subsequent evaluation will result in the decision to accept or reject the material. With the exception of accept and reject, which retain the meaning found in most dictionaries, all the words used in the chart are defined in Section A.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E1316 − 17a
Standard Terminology for
1
Nondestructive Examinations
This standard is issued under the fixed designation E1316; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INDEX OF TERMS
Section
A: Common NDT Terms
B: Acoustic Emission (AE) Terms
C: Electromagnetic Testing (ET) Terms
D: Gamma- and X-Radiologic Testing (RT) Terms
E: Leak Testing (LT) Terms
F: Liquid Penetrant Testing (PT) Terms
G: Magnetic Particle Testing (MT) Terms
H: Neutron Radiologic Testing (NRT) Terms
I: Ultrasonic Testing (UT) Terms
J: Infrared Testing (IRT) Terms
K: Holographic Testing (HT) Terms
L: Visual Testing (VT) Terms
1. Scope Radiologic Testing (RT) is often used to examine material to
detect internal discontinuities.)
1.1 This standard defines the terminology used in the
standards prepared by the E07 Committee on Nondestructive
1.3 Section A defines terms that are common to multiple
Testing. These nondestructive testing (NDT) methods include:
NDT methods, whereas, the subsequent sections define terms
acoustic emission, electromagnetic testing, gamma- and
pertaining to specific NDT methods.
X-radiology, leak testing, liquid penetrant testing, magnetic
1.4 As shown on the chart below, when nondestructive
particle testing, neutron radiology and gauging, ultrasonic
testing produces an indication, the indication is subject to
testing, and other technical methods.
interpretation as false, nonrelevant or relevant. If it has been
1.2 Committee E07 recognizes that the terms examination,
interpreted as relevant, the necessary subsequent evaluation
testing and inspection are commonly used as synonyms in
will result in the decision to accept or reject the material.With
nondestructive testing. For uniformity and consistency in E07
the exception of accept and reject, which retain the meaning
nondestructive testing standards, Committee E07 encourages
found in most dictionaries, all the words used in the chart are
the use of the term examination and its derivatives when
defined in Section A.
describing the application of nondestructive test methods.
There are, however, appropriate exceptions when the term test
and its derivatives may be used to describe the application of
a nondestructive test, such as measurements which produce a
numeric result (for example, when using the leak testing
methodtoperformaleaktestonacomponent,oranultrasonic
measurementofvelocity).Additionally,thetermtestshouldbe
used when referring to the NDT method, that is, Radiologic
Testing (RT), UltrasonicTesting (UT), and so forth. (Example:
1
ThisterminologyisunderthejurisdictionofCommitteeE07onNondestructive
Testing and is the direct responsibility of Subcommittee E07.92 on Editorial
Review.
Current edition approved June 15, 2017. Published July 2017. Originally
approved in 1989. Last previous edition approved in 2017 as E1316–17. DOI:
10.1520/E1316-17a.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E1316 − 17a
prepared by Committee E07 on Nondestructive Testing and published in
1.5 This international standard was developed in accor-
the Annual Book of ASTM Standards, Volumes 03.03 and 03.04.
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
3. Significance and Use
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
3.1 Thetermsfoundinthisstandardareintendedtobeused
Barriers to Trade (TBT) Committee.
uniformly and consistently in all nondestructive testing stan-
dards. The purpose of this standard is to promote a clear
2. Referenced Documents
understanding and interpretation of the NDT standards in
2
2.1 ASTM Standards:
which they are used.
NOTE 1—This standard defines the terminology used in the standards
4. Terminology
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Section A: Common NDT Terms
The terms defined in Section A are the direct responsibility of Subcommittee E07.92, Editorial Review.
acceptable quality level—the maximum percent defective or flaw, n—an imperfection or discontinuity that may be detect-
the maximum number of units defective per hundred units able by nondestructive testing and is not necessarily reject-
that, for the purpose of sampling test, can be considered able.
satisfact
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E1316 − 17 E1316 − 17a
Standard Terminology for
1
Nondestructive Examinations
This standard is issued under the fixed designation E1316; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INDEX OF TERMS
Section
A: Common NDT Terms
B: Acoustic Emission (AE) Terms
C: Electromagnetic Testing (ET) Terms
D: Gamma- and X-Radiologic Testing (RT) Terms
E: Leak Testing (LT) Terms
F: Liquid Penetrant Testing (PT) Terms
G: Magnetic Particle Testing (MT) Terms
H: Neutron Radiologic Testing (NRT) Terms
I: Ultrasonic Testing (UT) Terms
J: Infrared Testing (IRT) Terms
K: Holographic Testing (HT) Terms
L: Visual Testing (VT) Terms
1. Scope
1.1 This standard defines the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing.
These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak
testing, liquid penetrant testing, magnetic particle testing, neutron radiology and gauging, ultrasonic testing, and other technical
methods.
1.2 Committee E07 recognizes that the terms examination, testing and inspection are commonly used as synonyms in
nondestructive testing. For uniformity and consistency in E07 nondestructive testing standards, Committee E07 encourages the use
of the term examination and its derivatives when describing the application of nondestructive test methods. There are, however,
appropriate exceptions when the term test and its derivatives may be used to describe the application of a nondestructive test, such
as measurements which produce a numeric result (for example, when using the leak testing method to perform a leak test on a
component, or an ultrasonic measurement of velocity). Additionally, the term test should be used when referring to the NDT
method, that is, Radiologic Testing (RT), Ultrasonic Testing (UT), and so forth. (Example: Radiologic Testing (RT) is often used
to examine material to detect internal discontinuities.)
1.3 Section A defines terms that are common to multiple NDT methods, whereas, the subsequent sections define terms
pertaining to specific NDT methods.
1.4 As shown on the chart below, when nondestructive testing produces an indication, the indication is subject to interpretation
as false, nonrelevant or relevant. If it has been interpreted as relevant, the necessary subsequent evaluation will result in the
decision to accept or reject the material. With the exception of accept and reject, which retain the meaning found in most
dictionaries, all the words used in the chart are defined in Section A.
1
This terminology is under the jurisdiction of Committee E07 on Nondestructive Testing and is the direct responsibility of Subcommittee E07.92 on Editorial Review.
Current edition approved Feb. 1, 2017June 15, 2017. Published February 2017July 2017. Originally approved in 1989. Last previous edition approved in 20162017 as
E1316 – 16a.E1316 – 17. DOI: 10.1520/E1316-17.10.1520/E1316-17a.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E1316 − 17a
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
NOTE 1—This standard defines the terminology used in the standards prepared by Committee E07 on Nondestructive Testing and published in the
Annual Book of ASTM Standards, Volume 03.03.Volumes 03.03 and 03.04.
3. Significance and Use
3.1 The terms found in this standard are intended to be used uniformly and consistently in all nondestructive testing standards.
The purpose of this standard is to promote a clear understanding and interpretation of the NDT standards in which they are used.
4. Terminology
Section A: Common NDT Terms
The terms defined in Section A are the direct responsibility of Subcommittee E07.92, Editorial Review.
acceptable quality level—the maximum percent defective or the maximum number of units defective per hundred units that, for
the purpose of sampling test, ca
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.