ASTM F2412-18a
(Test Method)Standard Test Methods for Foot Protection
Standard Test Methods for Foot Protection
SIGNIFICANCE AND USE
4.1 These test methods contain requirements to evaluate the performance of footwear for the following:
4.1.1 Impact resistance for the toe area of footwear (I),
4.1.2 Compression resistance for the toe area of footwear (C),
4.1.3 Metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot (Mt),
4.1.4 Conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals (Cd),
4.1.5 Electric hazard to protect the wearer when accidentally stepping on live electric wires (EH),
4.1.6 Static dissipative properties to reduce hazards that result from a build up of static charge where there is an underlying risk of accidental contact with live electrical circuits (SD), and
4.1.7 Puncture resistance footwear devices (PR).
4.2 Any changes to the original components of safety toe footwear such as replacing or adding after-market footbeds/inserts could cause non-compliance to any or all parts of this standard rendering the ASTM label invalid. Protective toe footwear specimens or samples shall be retested for any of the following changes.
4.2.1 Change in material used to make protective toe cap, change in protective cap manufacturer, change in the design of the toe cap.
4.2.2 Change in construction method used to make footwear or change in factory in which footwear is produced.
4.2.3 Change in the upper or insole material thickness greater than 25 %.
4.2.4 Change in the out sole or midsole, including its hardness.
4.2.5 Change in shape of last used in the manufacturing of footwear.
4.2.6 Change in material or supplier of protective insole.
4.2.7 Change in material or supplier of met guard.
SCOPE
1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury.
1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety standards.
1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods can be used to determine any one, or all of the following: (1) impact resistance (I), (2) compression resistance (C), (3) metatarsal impact resistance (Mt), (4) resistance to electrical conductivity (Cd), (5) resistance to electric hazard (EH), (6) static dissipative performance (SD), and (7) puncture resistance (PR).
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2412 − 18a
Standard Test Methods for
1
Foot Protection
This standard is issued under the fixed designation F2412; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
For more than sixty years, the predecessor to these test methods, ANSI Z41, established the
performance criteria for a wide range of footwear to protect from the hazards that affect the personal
safetyofworkers.ThevalueofthesestandardswasrecognizedearlyinthehistoryoftheOccupational
Safety and Health Administration (OSHA) and incorporated as a reference standard in the Code of
Federal Regulation (CFR) Section 1910.
1. Scope 2. Referenced Documents
2
1.1 These test methods measure the resistance of footwear 2.1 ASTM Standards:
to a variety of hazards that can potentially result in injury. B117 Practice for Operating Salt Spray (Fog) Apparatus
3
2.2 CSA Standard:
1.2 These test methods may be used to test for compliance
CAN/CSA Z195 Protective Footwear
to minimum performance requirements in established safety
standards.
3. Terminology
1.2.1 By agreement between the purchaser and the supplier,
or as required by established safety standards, these test
3.1 Definitions:
methods can be used to determine any one, or all of the
3.1.1 footbed (removable), n—also known as ‘insock,’ a
following: (1) impact resistance (I), (2) compression resistance
component typically made of a foam material with a leather or
(C), (3) metatarsal impact resistance (Mt), (4) resistance to
fabric cover/sockliner and often shaped or contoured covering
electrical conductivity (Cd), (5) resistance to electric hazard
the entire insole board which can be inserted between the foot
(EH), (6) static dissipative performance (SD), and (7) puncture
and insole board.
resistance (PR).
3.1.2 insole, n—foundation of the shoe; the inner sole of the
1.3 The values stated in SI units are to be regarded as the
shoe which is next to the foot, under the sock liner or insert,
standard. The values given in parentheses are for information
onto which the upper is lasted.
only.
3.1.3 last, n—solid hinged form, in the general shape of a
1.4 This standard does not purport to address all of the
foot, around which footwear is constructed.
safety concerns, if any, associated with its use. It is the
3.1.4 lasting, v—building of footwear around a specific foot
responsibility of the user of this standard to establish appro-
form.
priate safety, health, and environmental practices and deter-
3.1.5 lining, n—term used to describe all components that
mine the applicability of regulatory limitations prior to use.
can be used to construct the interior of the upper portion of the
1.5 This international standard was developed in accor-
footwear.
dance with internationally recognized principles on standard-
3.1.6 outsole and heel, n—exterior bottom platform of the
ization established in the Decision on Principles for the
footwear; the bottom surface.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
3.1.7 product category, n—group of similar footwear items
Barriers to Trade (TBT) Committee.
manufactured for a specific hazard or hazards and that:
1 2
These test methods are under the jurisdiction of ASTM Committee F13 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Pedestrian/Walkway Safety and Footwear and are the direct responsibility of contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Subcommittee F13.30 on Footwear. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Aug. 1, 2018. Published August 2018. Originally the ASTM website.
3
approved in 2005. Last previous edition approved in 2018 as F2412 – 18. DOI: Available from Canadian Standards Association (CSA), 178 Rexdale Blvd.,
10.1520/F2412-18A. Toronto, ON Canada M9W1R3.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2412 − 18a
• Have same protective toe cap, protective insole or met- standard rendering the ASTM label invalid. Protective toe
guard materials footwear specimens or samples shall be retested for any of the
• Have the same supplier for each of those components following changes.
• Have the same outsole design, compound and hardness 4.2.1 Change in material used to make
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2412 − 18 F2412 − 18a
Standard Test Methods for
1
Foot Protection
This standard is issued under the fixed designation F2412; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
For more than sixty years, the predecessor to these test methods, ANSI Z41, established the
performance criteria for a wide range of footwear to protect from the hazards that affect the personal
safety of workers. The value of these standards was recognized early in the history of the Occupational
Safety and Health Administration (OSHA) and incorporated as a reference standard in the Code of
Federal Regulation (CFR) Section 1910.
These test methods contains test protocols developed in conjunction with ANSI Z41 as well as other
ASTM standards that are used to evaluate the performance of footwear when exposed to a variety of
hazards: (1) impact resistance (I) for the toe area of footwear; (2) compression resistance (C) for the
toe area of footwear; (3) metatarsal impact protection (Mt) that reduces the chance of injury to the
metatarsal bones at the top of the foot; (4) conductive properties (Cd) that reduce hazards that may
result from static electricity buildup and reduce the possibility of ignition of explosives and volatile
chemicals; (5) electric hazard resistant (EH) non-conductive; (6) static dissipative (SD) properties to
reduce hazards due to excessively low footwear electrical resistance that may exist where SD footwear
is required; and (7) puncture resistance (PR) of foot devices.
1. Scope
1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury.
1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety
standards.
1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods
can be used to determine any one, or all of the following: (1) impact resistance (I), (2) compression resistance (C), (3) metatarsal
impact resistance (Mt), (4) resistance to electrical conductivity (Cd), (5) resistance to electric hazard (EH), (6) static dissipative
performance (SD), and (7) puncture resistance (PR).
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
B117 Practice for Operating Salt Spray (Fog) Apparatus
1
These test methods are under the jurisdiction of ASTM Committee F13 on Pedestrian/Walkway Safety and Footwear and are the direct responsibility of Subcommittee
F13.30 on Footwear.
Current edition approved Feb. 1, 2018Aug. 1, 2018. Published March 2018August 2018. Originally approved in 2005. Last previous edition approved in 20112018 as
F2412 – 11.F2412 – 18. DOI: 10.1520/F2412-18.10.1520/F2412-18A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2412 − 18a
3
2.2 CSA Standard:
CAN/CSA Z195 Protective Footwear
3. Terminology
3.1 Definitions:
3.1.1 footbed (removable), n—also known as ‘insock,’ a component typically made of a foam material with a leather or fabric
cover/sockliner and often shaped or contoured covering the entire insole board which can be inserted between the foot and insole
board.
3.1.2 insole, n—foundation of the shoe; the inner sol
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.