ASTM C1775-22
(Specification)Standard Specification for Laminate Protective Jacket and Tape for Use over Thermal Insulation for Outdoor Applications
Standard Specification for Laminate Protective Jacket and Tape for Use over Thermal Insulation for Outdoor Applications
SCOPE
1.1 This specification addresses the minimum performance for flexible laminate protective jacket and a pressure sensitive adhesive tape for use over thermal insulation on pipes, duct, and equipment operating at both above and below ambient temperatures and installed outdoors, above ground. It does not include the following: protective metal jacket, homogenous plastic film jacket materials, modified asphalt jacket materials, and butyl rubber membranes.
1.2 This type of material shall consist of multiple layers of polymer film and aluminum foil laminated to one another with layer(s) of reinforcement as an option.
1.3 Jacket and tape materials covered by this specification shall have low water vapor permeance values; however, they are not necessarily always used as vapor retarders. The water vapor transmission tests address the jacket and tape materials only and do not address overlaps or taped joints. All materials shall be weather resistant and intended to have sufficient strength to provide protection for mechanical insulation.
1.4 Materials covered under this specification shall have a high, medium, or low surface emittance.
1.5 The top layer shall be on of the following: aluminum foil, a polymer film, or a polymer coating.
1.6 This specification includes jacket materials both with and without factory applied, pressure sensitive adhesives. The tape materials covered by this specification always have a factory applied, pressure sensitive adhesive.
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:C1775 −22
Standard Specification for
Laminate Protective Jacket and Tape for Use over Thermal
1
Insulation for Outdoor Applications
This standard is issued under the fixed designation C1775; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
1.1 This specification addresses the minimum performance
mine the applicability of regulatory limitations prior to use.
for flexible laminate protective jacket and a pressure sensitive
1.9 This international standard was developed in accor-
adhesive tape for use over thermal insulation on pipes, duct,
dance with internationally recognized principles on standard-
and equipment operating at both above and below ambient
ization established in the Decision on Principles for the
temperatures and installed outdoors, above ground. It does not
Development of International Standards, Guides and Recom-
include the following: protective metal jacket, homogenous
mendations issued by the World Trade Organization Technical
plastic film jacket materials, modified asphalt jacket materials,
Barriers to Trade (TBT) Committee.
and butyl rubber membranes.
1.2 This type of material shall consist of multiple layers of
2. Referenced Documents
polymer film and aluminum foil laminated to one another with 2
2.1 ASTM Standards:
layer(s) of reinforcement as an option.
C168 Terminology Relating to Thermal Insulation
1.3 Jacket and tape materials covered by this specification C1263 Test Method for Thermal Integrity of Flexible Water
shall have low water vapor permeance values; however, they
Vapor Retarders
are not necessarily always used as vapor retarders. The water C1338 Test Method for Determining Fungi Resistance of
vapor transmission tests address the jacket and tape materials
Insulation Materials and Facings
only and do not address overlaps or taped joints. All materials C1371 Test Method for Determination of Emittance of
shall be weather resistant and intended to have sufficient
Materials Near Room Temperature Using Portable Emis-
strength to provide protection for mechanical insulation. someters
D774 Test Method for Bursting Strength of Paper
1.4 Materials covered under this specification shall have a
D882 Test Method for Tensile Properties of Thin Plastic
high, medium, or low surface emittance.
Sheeting
1.5 The top layer shall be on of the following: aluminum
D1000 Test Methods for Pressure-Sensitive Adhesive-
foil, a polymer film, or a polymer coating.
Coated Tapes Used for Electrical and Electronic Applica-
1.6 This specification includes jacket materials both with tions
and without factory applied, pressure sensitive adhesives. The D1204 Test Method for Linear Dimensional Changes of
tape materials covered by this specification always have a Nonrigid Thermoplastic Sheeting or Film at Elevated
factory applied, pressure sensitive adhesive. Temperature
D3330 Test Method for PeelAdhesion of Pressure-Sensitive
1.7 The values stated in inch-pound units are to be regarded
Tape
as standard. The values given in parentheses are mathematical
D3759 Test Method for Breaking Strength and Elongation of
conversions to SI units that are provided for information only
Pressure-Sensitive Tape
and are not considered standard.
E96 Test Methods for Gravimetric Determination of Water
1.8 This standard does not purport to address all of the
Vapor Transmission Rate of Materials
safety concerns, if any, associated with its use. It is the
F1249 Test Method for Water Vapor Transmission Rate
Through Plastic Film and Sheeting Using a Modulated
Infrared Sensor
1
This specification is under the jurisdiction of ASTM Committee C16 on
Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on
2
Insulation Systems. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved March 1, 2022. Published March 2022. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2013. Last previous edition approved in 2014 as C1775 – 14. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1775-22. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1775−22
G154 Practice
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1775 − 14 C1775 − 22
Standard Specification for
Laminate Protective Jacket and Tape for Use over Thermal
1
Insulation for Outdoor Applications
This standard is issued under the fixed designation C1775; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification addresses the minimum performance for flexible laminate protective jacket and a pressure sensitive adhesive
tape for use over thermal insulation on pipes, duct, and equipment operating at both above and below ambient temperatures and
installed outdoors, above ground. It does not include the following: protective metal jacket, homogenous plastic film jacket
materials, modified asphalt jacket materials, and butyl rubber membranes.
1.2 This type of material shall consist of multiple layers of polymer film and aluminum foil laminated to one another with layer(s)
of reinforcement as an option.
1.3 Jacket and tape materials covered by this specification shall have low water vapor permeance values; however, they are not
necessarily always used as vapor retarders. The water vapor transmission tests address the jacket and tape materials only and do
not address overlaps or taped joints. All materials shall be weather resistant and intended to have sufficient strength to provide
protection for mechanical insulation.
1.4 Materials covered under this specification shall have a high, medium, or low surface emittance.
1.5 The top layer shall be on of the following: aluminum foil, a polymer film, or a polymer coating.
1.6 This specification includes jacket materials both with and without factory applied, pressure sensitive adhesives. The tape
materials covered by this specification always have a factory applied, pressure sensitive adhesive.
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1
This specification is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on Insulation
Systems.
Current edition approved Oct. 15, 2014March 1, 2022. Published November 2014March 2022. Originally approved in 2013. Last previous edition approved in 20132014
as C1775 – 13.14. DOI: 10.1520/C1775-14.10.1520/C1775-22.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1775 − 22
2. Referenced Documents
2
2.1 ASTM Standards:
C168 Terminology Relating to Thermal Insulation
C1136 Specification for Flexible, Low Permeance Vapor Retarders for Thermal Insulation
C1263 Test Method for Thermal Integrity of Flexible Water Vapor Retarders
C1338 Test Method for Determining Fungi Resistance of Insulation Materials and Facings
C1371 Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
D774 Test Method for Bursting Strength of Paper
D882 Test Method for Tensile Properties of Thin Plastic Sheeting
D1000 Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications
D1204 Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
D3330 Test Method for Peel Adhesion of Pressure-Sensitive Tape
D3759 Test Method for Breaking Strength and Elongation of Pressure-Sensitive Tape
E96 Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
F1249 Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Inf
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.