Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications

This document specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensils applications.
This standard is applicable to:
-   Circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including 12 mm and with a diameter from 100 mm up to and including 1 600 mm.
NOTE   Circles with a diameter up to 1 000 mm can be produced by blanking.
-   Hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a width up to 1 600 mm.
This document is not applicable to slugs for impact extrusions which are dealt with in other European Standards.

Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung von Küchengeschirr - Spezifikationen

Dieses Dokument legt die besonderen Anforderungen für Ronden und Rondenvormaterial aus Aluminium-Knetlegierung und Aluminiumlegierungen fest, die zur Herstellung von Küchengeschirr eingesetzt werden.
Diese Norm gilt für:
-   Ronden, die aus kalt- bzw. warmgewalztem Rondenvormaterial mit einer Dicke von 0,2 mm bis 12 mm und einem Durchmesser von 100 mm bis 1 600 mm hergestellt werden;
ANMERKUNG   Ronden mit einem Durchmesser von 1 000 mm können durch Stanzen (geschlossener Schnitt) hergestellt werden.
-   kalt- bzw. warmgewalztes Rondenvormaterial mit einer Dicke von 0,2 mm bis 12 mm und einer Breite bis 1 600 mm.
Dieses Dokument gilt nicht für Butzen zum Fließpressen, die in anderen Europäischen Normen behandelt werden.

Aluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications culinaires - Spécifications

Le présent document spécifie les exigences particulières applicables à l'aluminium et aux alliages d'aluminium corroyés sous forme de disques ou d'ébauches pour disques destinés à la fabrication d’ustensiles culinaires.
Il s'applique aux :
-   Disques fabriqués à partir d'ébauches pour disques laminées à chaud ou à froid, d'épaisseur comprise entre 0,2 mm et 12 mm inclus, et de diamètre compris entre 100 mm et 1 600 mm inclus.
NOTE   Les disques dont le diamètre n'excède pas 1 000 mm peuvent être fabriqués par poinçonnage.
-   Ébauches pour disques laminées à chaud ou à froid, d'épaisseur comprise entre 0,2 mm et 12 mm inclus et de largeur inférieure ou égale à 1 600 mm.
Il ne s'applique pas aux pions de filage par choc qui sont traités dans d'autres Normes européennes.

Aluminij in aluminijeve zlitine - Rondele in polizdelki za izdelavo jedilnih pripomočkov in posode - Specifikacije

Ta dokument določa posamezne zahteve za gneteni aluminij in aluminijeve zlitine v obliki rondel ali polizdelkov za uporabo pri izdelavi jedilnih pripomočkov in posode.
Ta standard se uporablja za:
–   rondele, izdelane iz vroče ali hladno valjanih polizdelkov z debelino od 0,2 mm do vključno 12 mm in s premerom od 100 mm do vključno 1600 mm.
OPOMBA:   Rondele s premerom do 1000 mm je mogoče izdelati s finim rezanjem.
–   vroče ali hladno valjane polizdelke z debelino od 0,2 mm do vključno 12 mm in s premerom do 1600 mm.
Ta dokument se ne uporablja za kovinske palice za udarno iztiskanje, ki so obravnavane v drugih evropskih standardih.

General Information

Status
Published
Public Enquiry End Date
14-Mar-2021
Publication Date
30-Mar-2022
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
30-Mar-2022
Due Date
04-Jun-2022
Completion Date
31-Mar-2022

RELATIONS

Buy Standard

Standard
SIST EN 851:2022
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
oSIST prEN 851:2021
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 851:2022
01-maj-2022
Nadomešča:
SIST EN 851:2014
Aluminij in aluminijeve zlitine - Rondele in polizdelki za izdelavo jedilnih
pripomočkov in posode - Specifikacije

Aluminium and aluminium alloys - Circle and circle stock for the production of culinary

utensils - Specifications

Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung

von Küchengeschirr - Spezifikationen

Aluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications

culinaires - Spécifications
Ta slovenski standard je istoveten z: EN 851:2022
ICS:
77.150.10 Aluminijski izdelki Aluminium products
97.040.60 Kuhinjska posoda, jedilni Cookware, cutlery and
servisi in jedilni pribor flatware
SIST EN 851:2022 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 851:2022
---------------------- Page: 2 ----------------------
SIST EN 851:2022
EN 851
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 77.150.10 Supersedes EN 851:2014
English Version
Aluminium and aluminium alloys - Circle and circle stock
for the production of culinary utensils - Specifications

Aluminium et alliages d'aluminium - Disques et Aluminium und Aluminiumlegierungen - Ronden und

ébauches pour disques pour applications culinaires - Rondenvormaterial zur Herstellung von

Spécifications Küchengeschirr - Spezifikationen
This European Standard was approved by CEN on 14 February 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 851:2022 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 851:2022
EN 851:2021 (E)
Contents Page

European foreword ...................................................................................................................................................... 3

1 Scope .................................................................................................................................................................... 4

2 Normative references .................................................................................................................................... 4

3 Terms and definitions ................................................................................................................................... 4

4 Technical conditions for inspection and delivery ............................................................................... 5

4.1 General................................................................................................................................................................ 5

4.2 Orders or tenders ........................................................................................................................................... 5

5 Mechanical properties .................................................................................................................................. 6

5.1 General................................................................................................................................................................ 6

5.2 Earing .................................................................................................................................................................. 6

6 Tolerances on dimensions and form ....................................................................................................... 6

6.1 General................................................................................................................................................................ 6

6.2 Diameter ............................................................................................................................................................ 6

6.3 Thickness ........................................................................................................................................................... 7

6.4 Tolerances on flatness for circle ............................................................................................................... 7

6.5 Edge burr tolerances for circle .................................................................................................................. 7

7 Other requirements ....................................................................................................................................... 7

Bibliography ................................................................................................................................................................. 12

---------------------- Page: 4 ----------------------
SIST EN 851:2022
EN 851:2022 (E)
European foreword

This document (EN 851:2022) has been prepared by Technical Committee CEN/TC 132 “Aluminium

and aluminium alloys”, the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by September 2022, and conflicting national standards

shall be withdrawn at the latest by September 2022.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 851:2014.
In comparison with to the previous edition, Clause 6.4 was modified.

Any feedback and questions on this document should be directed to the users’ national standards body.

A complete listing of these bodies can be found on the CEN website.

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
---------------------- Page: 5 ----------------------
SIST EN 851:2022
EN 851:2022 (E)
1 Scope

This document specifies the particular requirements for wrought aluminium and aluminium alloys in

the form of circle or circle stock for culinary utensils applications.
This document is applicable to:

— circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and

including 12 mm and with a diameter from 100 mm up to and including 1 600 mm;
NOTE Circles with a diameter up to 1 000 mm can be produced by blanking.

— hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a

width up to 1 600 mm.

This document is not applicable to slugs for impact extrusions which are dealt with in other European

Standards.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

EN 485-1:2016, Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for

inspection and delivery

EN 485-2, Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties

EN 485-3, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and

form for hot-rolled products

EN 485-4, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and

dimensions for cold-rolled products
EN 515, Aluminium and aluminium alloys - Wrought products - Temper designations

EN 602, Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-finished

products used for the fabrication of articles for use in contact with foodstuff
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
circle
circular flat product obtained by circular sawing or shearing, or by
...

SLOVENSKI STANDARD
oSIST prEN 851:2021
01-marec-2021
Aluminij in aluminijeve zlitine - Rondele in polizdelki za izdelavo jedilnih
pripomočkov in posode - Specifikacije

Aluminium and aluminium alloys - Circle and circle stock for the production of culinary

utensils - Specifications

Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung

von Küchengeschirr - Spezifikationen

Aluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications

culinaires - Spécifications
Ta slovenski standard je istoveten z: prEN 851
ICS:
77.150.10 Aluminijski izdelki Aluminium products
97.040.60 Kuhinjska posoda, jedilni Cookware, cutlery and
servisi in jedilni pribor flatware
oSIST prEN 851:2021 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 851:2021
---------------------- Page: 2 ----------------------
oSIST prEN 851:2021
DRAFT
EUROPEAN STANDARD
prEN 851
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2021
ICS 77.150.10 Will supersede EN 851:2014
English Version
Aluminium and aluminium alloys - Circle and circle stock
for the production of culinary utensils - Specifications

Aluminium et alliages d'aluminium - Disques et Aluminium und Aluminiumlegierungen - Ronden und

ébauches pour disques pour applications culinaires - Rondenvormaterial zur Herstellung von

Spécifications Küchengeschirr - Spezifikationen

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee

CEN/TC 132.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 851:2021 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 851:2021
prEN 851:2021 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

1 Scope .................................................................................................................................................................... 4

2 Normative references .................................................................................................................................... 4

3 Terms and definitions ................................................................................................................................... 5

4 Technical conditions for inspection and delivery ............................................................................... 5

4.1 General ................................................................................................................................................................ 5

4.2 Orders or tenders ............................................................................................................................................ 5

5 Mechanical properties ................................................................................................................................... 6

5.1 General ................................................................................................................................................................ 6

5.2 Earing .................................................................................................................................................................. 6

6 Tolerances on dimensions and form ........................................................................................................ 7

6.1 General ................................................................................................................................................................ 7

6.2 Diameter ............................................................................................................................................................. 7

6.3 Thickness ........................................................................................................................................................... 7

6.4 Tolerances on flatness for circle ................................................................................................................ 7

6.5 Edge burr tolerances for circle ................................................................................................................... 7

7 Other requirements ....................................................................................................................................... 7

Bibliography ................................................................................................................................................................. 12

---------------------- Page: 4 ----------------------
oSIST prEN 851:2021
prEN 851:2021 (E)
European foreword

This document (prEN 851:2021) has been prepared by Technical Committee CEN/TC 132 “Aluminium and

aluminium alloys”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 851:2014.
Compared to the previous edition, 6.4 was modified.
---------------------- Page: 5 ----------------------
oSIST prEN 851:2021
prEN 851:2021 (E)
1 Scope

This document specifies the particular requirements for wrought aluminium and aluminium alloys in the form

of circle or circle stock for culinary utensils applications.
This standard is applicable to:

— Circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including

12 mm and with a diameter from 100 mm up to and including 1 600 mm.
NOTE Circles with a diameter up to 1 000 mm can be produced by blanking.

— Hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a width

up to 1 600 mm.

This document is not applicable to slugs for impact extrusions which are dealt with in other European

Standards.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content constitutes

requirements of this document. For dated references, only the edition cited applies. For undated references,

the latest edition of the referenced document (including any amendments) applies.

EN 485-1:2016, Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for

inspection and delivery

EN 485-2, Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties

EN 485-3, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form

for hot-rolled products

EN 485-4, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions

for cold-rolled products
EN 515, Aluminium and aluminium alloys - Wrought products - Temper designations

EN 602, Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-finished products

used for the fabrication of articles for use in contact with foodstuff
---------------------- Page: 6 ----------------------
oSIST prEN 851:2021
prEN 851:2021 (E)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
3.1
circle

circular flat product obtained by circular sawing or shearing, or by blanking of a flat rolled product with a

uniform thickness over 0,20 mm
3.2
circle stock

flat rolled product of rectangular cross-section with uniform thickness over 0,20 mm, supplied in coils, sheets,

or plates, usually with sheared or sawn edges, and intended to be sawn, sheared or blanked into f

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.