EN ISO 5084:1996

Textiles - Determination of thickness of textiles and textile products (ISO 5084:1996)

Describes a method for the determination of the thickness of textiles and textile products under specified pressure. Not applicable to textile floor coverings, nonwovens, geotextiles and coated fabrics. replaces the first edition.

Textilien - Bestimmung der Dicke von Textilien und textilen Erzeugnissen (ISO 5084:1996)

Diese Internationale Norm legt ein Verfahren zur Bestimmung der Dicke von Textilien und Textilerzeugnissen unter festgelegtem Druck fest. Sie gilt nicht für textile Bodenbeläge, Vliesstoffe, Geotextilien und beschichtete Textilien, für die eigene Normen bestehen (siehe Anhang B).

Textiles - Détermination de l'épaisseur des textiles et produits textiles (ISO 5084:1996)

La présente Norme internationale prescrit une méthode pour la détermination de l'épaisseur, sous une pression définie, des textiles et produits textiles. Elle n'est pas applicable aux revêtements de sol textiles, aux nontissés, aux géotextiles et aux supports textiles revêtus pour lesquels il existe des normes spécifiques (voir annexe B).

Tekstilije - Ugotavljanje debeline tekstilij (ISO 5084:1996)

General Information

• Status: Published
• Publication Date: 31-Aug-1996
• Withdrawal Date: 30-Mar-1997
• ICS: 59.080 - Products of the textile industry
• Technical Committee: CEN/TC 248 - Textiles and textile products
• Drafting Committee: CEN/TC 248/SC 2 - Physical properties
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 14-Jun-2006
• Completion Date: 14-Jun-2006
• Ref Project: SIST EN ISO 5084:1999 - Textiles - Determination of thickness of textiles and textile products (ISO 5084:1996)

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-1999
Tekstilije - Ugotavljanje debeline tekstilij (ISO 5084:1996)
Textiles - Determination of thickness of textiles and textile products (ISO 5084:1996)
Textilien - Bestimmung der Dicke von Textilien und textilen Erzeugnissen (ISO
5084:1996)
Textiles - Détermination de l'épaisseur des textiles et produits textiles (ISO 5084:1996)
Ta slovenski standard je istoveten z: EN ISO 5084:1996
ICS:
59.080.30 Tkanine Textile fabrics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

IS0
INTERNATIONAL
STANDARD
Second edition
1996-09-o 1
- Determination of thickness of
Textiles
textiles and textile products
- Dktermination de I’6paisseur des textiles et prod&s textiles
Textiles
Reference number
IS0 50847 996(E)
IS0 5084: 1996(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 5084 was prepared by Technical Committee
I SO/TC 38, Textiles.
This second edition cancels and replaces the first edition
(IS0 5084:1977), which has been technically revised.
Annex A forms an integral part of this International Standard. Annex B is
for information only.
0 IS0 1996
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Org anization for Standardization
Case Postale 56 l CH-121 1 Geneve 20 l Switzerland
Printed in Switzerland
ii
IS0 5084: 1996(E)
INTERNATIONAL STANDARD 0 IS0
Textiles - Determination of thickness of textiles and
textile products
4 Principle
1 Scope
The thickness of a specimen is measured as the dis-
This International Standard specifies a method for the
tance between the reference plate on which the
determination of the thickness of textiles and textile
specimen rests and a parallel circular presser-foot that
products when under a specified pressure. It is not
exerts a specified pressure on the area of the textile
applicable to textile floor coverings, nonwovens,
under test.
geotextiles and coated fabrics for which specific
International Standards exist (see annex B).
A test specimen is placed between two reference
plates which exert a known pressure on the speci-
men. The perpendicular distance between the refer-
ence plates is measured and recorded after a
2 Normative references
specified time.
The following standards contain provisions which,
through reference in this text, constitute provisions 5 Apparatus
of this International Standard. At the time of publi-
cation, the editions indicated were valid. All standards
5.1 Thickness tester
are subject to revision, and parties to agreements
The confirmation system for the thickness tester shall
based on this International Standard are encouraged
to investigate the possibility of applying the most re- comply with IS0 IOOIZ-1. The thickness tester shall
cent editions of the standards indicated below. incorporate (or be equipped with) the following el-
ements.
Members of IEC and IS0 maintain registers of cur-
rently valid International Standards.
5.1.1 Interchangeable presser-feet, of area appro-
IS0 139: 1973, Textiles - Standard atmospheres for
priate to the type of fabric to be tested.
conditioning and testing.
The recommended pressure-foot area for the test is
IS0 10012-I : 1992, Quality assurance requirements (2 000 + 20) mm’, corresponding to a circular
for measuring equipment - Part I: Metrological presser-foot of diameter (50,5 + 0,2) mm (see also
-
confirmation system for measuring equlpmen t. annex A). If other test areas have to be used, this
shall be agreed by the interested parties and shall be
stated in the test report.
5.1.2 Reference plate, with a plane upper surface
3 Definition
of diameter at least 50 mm greater than that of the
For the purposes of this International Standard, the presser-foot (5.1.1).
following definition applies.
5.1.3 Means for moving
...