EN 15435:2008
(Main)Precast concrete products - Normal weight and lightweight concrete shuttering blocks - Product properties and performance
Precast concrete products - Normal weight and lightweight concrete shuttering blocks - Product properties and performance
This European Standard specifies the properties, performance and test methods of factory made, non-load bearing hollow concrete shuttering blocks made from normal weight or lightweight aggregates or a combination of both. Shuttering blocks may include vertical or horizontal interlocking features and factory installed supplementary insulation. Shuttering blocks are intended to be used to form walls and partitions when filled with concrete or mortar. Concrete shuttering blocks rely on a concrete or mortar infill for their structural performance and are not intended to be used unfilled.
This standard does not cover masonry units covered in EN 771-3.
Betonfertigteile - Schalungssteine aus Normal- und Leichtbeton - Produkteigenschaften und Leistungsmerkmale
Dieser Teil von ISO 8835 legt Anforderungen für Anästhesie Atemsysteme fest, die entweder vom Hersteller montiert geliefert werden oder vom Betreiber nach den Herstelleranweisungen zusammen gebaut werden.
Er behandelt auch Absorber Baugruppen für ein Kreissystem, Abgasventile, Ein und Ausatemventile und für einige Konstruktionen diejenigen Teile eines Anästhesie Atemsystems, die in ein Anästhesiesystem eingebaut sind, einschließlich des Weges eines Anästhesie Beatmungsgeräts für ausgeatmetes Gas und der Teile eines nicht vom Anwender abnehmbaren Anästhesiegas Fortleitungssystems (AGFS).
Dieser Teil von ISO 8835 behandelt nicht die Leistung von Atemsystemen hinsichtlich der Beseitigung ausgeatmeten Kohlenstoffdioxids, da dies ein komplexer Vorgang ist und von der Wechselwirkung mit dem Patienten, dem Frischgasstrom, dem Absorptionsmittel für das Kohlenstoffdioxid und vom Atemsystem selbst abhängt.
Dieser Teil von ISO 8835 gilt nicht für Atemsysteme, die für die Verwendung mit brennbaren Anästhesiemitteln bzw. gasen vorgesehen sind.
Produits préfabriqués en béton - Blocs de coffrage en béton de granulats courants et légers - Propriétés et performances des produits
La présente Norme européenne spécifie les propriétés, les performances et les méthodes d’essais des blocs
de coffrage en béton non porteurs, fabriqués à partir de granulats courants ou légers ou une combinaison des
deux. Les blocs de coffrage peuvent comporter des dispositifs d'emboîtement ainsi qu'un isolant thermique
supplémentaire mis en oeuvre en usine. Les blocs de coffrage sont destinés à être utilisés pour la réalisation
de murs et de cloisons, une fois remplis de béton ou de mortier. Les blocs de coffrage en béton sont
dépendants du remplissage de béton ou de mortier pour leur performance structurale et ne sont pas destinés
à être utilisés non remplis.
La présente norme ne couvre pas les éléments de maçonnerie couverts par l'EN 771-3.
Montažni betonski izdelki - Normalni in lahki betonski bloki - Značilnosti in obnašanje izdelkov
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2008
Montažni betonski izdelki - Normalni in lahki betonski bloki - Značilnosti in
obnašanje izdelkov
Precast concrete products - Normal weight and lightweight concrete shuttering blocks -
Product properties and performance
Betonfertigteile - Schalungssteine aus Normal- und Leichtbeton - Produkteigenschaften
und Leistungsmerkmale
Produits préfabriqués en béton - Blocs de coffrage en béton de granulats courants et
légers - Exigences et méthode d'essai
Ta slovenski standard je istoveten z: EN 15435:2008
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 15435
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 91.100.30
English Version
Precast concrete products - Normal weight and lightweight
concrete shuttering blocks - Product properties and performance
Produits préfabriqués en béton - Blocs de coffrage en Betonfertigteile - Schalungssteine aus Normal- und
béton de granulats courants et légers - Propriétés et Leichtbeton - Produkteigenschaften und
performances des produits Leistungsmerkmale
This European Standard was approved by CEN on 18 March 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15435:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.4
1 Scope.5
2 Normative references.5
3 Terms, definitions and symbols.6
3.1 Terms and definitions .6
3.2 Symbols.7
4 Requirements.8
4.1 General.8
4.2 Raw materials and concrete .9
4.3 Dangerous substances.9
4.4 Geometric properties.9
4.5 Density.10
4.6 Moisture movement.10
4.7 Reaction to fire.10
4.8 Water vapour permeability.10
4.9 Mechanical strength.10
4.10 Acoustic properties.11
4.11 Thermal properties.11
4.12 Water absorption by capillarity .11
4.13 Durability.11
5 Test methods.12
5.1 Geometric properties.12
5.2 Density.14
5.3 Mechanical strength.15
6 Classification.15
7 Marking.16
8 Evaluation of conformity.16
8.1 General.16
8.2 Initial type testing .16
8.3 Factory production control.17
Annex A (normative) Determination of web tensile strength .18
A.1 Principle.18
A.2 Apparatus.18
A.3 Procedure.19
A.4 Determining the tensile strength of webs .21
A.5 Test report.23
Annex B (normative) Determination of shell flexural strength.24
B.1 Principle.24
B.2 Apparatus.24
B.3 Procedure.24
B.4 Determining the flexural strength of the shells .24
B.5 Test report.28
Annex C (normative) Sampling for initial type testing .29
C.1 General.29
C.2 Sampling procedure.29
C.3 Place and dates of inspection and acceptance testing .31
Annex D (normative) Compliance criteria for initial type testing and for independent batch
acceptance testing .32
Annex E (informative) Example of inspection schemes .33
E.1 Equipment inspection.33
E.2 Materials inspection.34
E.3 Production process inspection.35
E.4 Product inspection.36
E.5 Switching rules.37
Annex F (informative) Filling pressure of concrete infill .38
Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU
Construction Products Directive .39
ZA.1 Scope and relevant characteristics.39
ZA.2 Procedure for attestation of conformity of concrete shuttering blocks.40
ZA.3 CE marking and labelling .42
Bibliography.44
Foreword
This document (EN 15435:2008) has been prepared by Technical Committee CEN/TC 229 “Precast concret
products”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at
the latest by January 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Construction Products Directive
(89/106/EC).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
It also takes into account the “Common rules for precast concrete products” in EN 13369.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
1 Scope
This European Standard specifies the properties, performance and test methods of factory made, non-load
bearing hollow concrete shuttering blocks made from normal weight or lightweight aggregates or a
combination of both. Shuttering blocks may include vertical or horizontal interlocking features and factory
installed supplementary insulation. Shuttering blocks are intended to be used to form walls and partitions
when filled with concrete or mortar. Concrete shuttering blocks rely on a concrete or mortar infill for their
structural performance and are not intended to be used unfilled.
This standard does not cover masonry units covered in EN 771-3.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 772-11, Methods of test for masonry units — Part 11: Determination of water absorption of aggregate
concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of
water absorption of clay masonry units
EN 772-14, Methods of test for maso
...
SLOVENSKI STANDARD
01-september-2008
0RQWDåQLEHWRQVNLL]GHONL1RUPDOQLLQODKNLEHWRQVNLEORNL=QDþLOQRVWLLQ
REQDãDQMHL]GHONRY
Precast concrete products - Normal weight and lightweight concrete shuttering blocks -
Product properties and performance
Betonfertigteile - Schalungssteine aus Normal- und Leichtbeton - Produkteigenschaften
und Leistungsmerkmale
Produits préfabriqués en béton - Blocs de coffrage en béton de granulats courants et
légers - Exigences et méthode d'essai
Ta slovenski standard je istoveten z: EN 15435:2008
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 15435
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 91.100.30
English Version
Precast concrete products - Normal weight and lightweight
concrete shuttering blocks - Product properties and performance
Produits préfabriqués en béton - Blocs de coffrage en Betonfertigteile - Schalungssteine aus Normal- und
béton de granulats courants et légers - Propriétés et Leichtbeton - Produkteigenschaften und
performances des produits Leistungsmerkmale
This European Standard was approved by CEN on 18 March 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15435:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.4
1 Scope.5
2 Normative references.5
3 Terms, definitions and symbols.6
3.1 Terms and definitions .6
3.2 Symbols.7
4 Requirements.8
4.1 General.8
4.2 Raw materials and concrete .9
4.3 Dangerous substances.9
4.4 Geometric properties.9
4.5 Density.10
4.6 Moisture movement.10
4.7 Reaction to fire.10
4.8 Water vapour permeability.10
4.9 Mechanical strength.10
4.10 Acoustic properties.11
4.11 Thermal properties.11
4.12 Water absorption by capillarity .11
4.13 Durability.11
5 Test methods.12
5.1 Geometric properties.12
5.2 Density.14
5.3 Mechanical strength.15
6 Classification.15
7 Marking.16
8 Evaluation of conformity.16
8.1 General.16
8.2 Initial type testing .16
8.3 Factory production control.17
Annex A (normative) Determination of web tensile strength .18
A.1 Principle.18
A.2 Apparatus.18
A.3 Procedure.19
A.4 Determining the tensile strength of webs .21
A.5 Test report.23
Annex B (normative) Determination of shell flexural strength.24
B.1 Principle.24
B.2 Apparatus.24
B.3 Procedure.24
B.4 Determining the flexural strength of the shells .24
B.5 Test report.28
Annex C (normative) Sampling for initial type testing .29
C.1 General.29
C.2 Sampling procedure.29
C.3 Place and dates of inspection and acceptance testing .31
Annex D (normative) Compliance criteria for initial type testing and for independent batch
acceptance testing .32
Annex E (informative) Example of inspection schemes .33
E.1 Equipment inspection.33
E.2 Materials inspection.34
E.3 Production process inspection.35
E.4 Product inspection.36
E.5 Switching rules.37
Annex F (informative) Filling pressure of concrete infill .38
Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU
Construction Products Directive .39
ZA.1 Scope and relevant characteristics.39
ZA.2 Procedure for attestation of conformity of concrete shuttering blocks.40
ZA.3 CE marking and labelling .42
Bibliography.44
Foreword
This document (EN 15435:2008) has been prepared by Technical Committee CEN/TC 229 “Precast concret
products”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at
the latest by January 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Construction Products Directive
(89/106/EC).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
It also takes into account the “Common rules for precast concrete products” in EN 13369.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
1 Scope
This European Standard specifies the properties, performance and test methods of factory made, non-load
bearing hollow concrete shuttering blocks made from normal weight or lightweight aggregates or a
combination of both. Shuttering blocks may include vertical or horizontal interlocking features and factory
installed supplementary insulation. Shuttering blocks are intended to be used to form walls and partitions
when filled with concrete or mortar. Concrete shuttering blocks rely on a concrete or mortar infill for their
structural performance and are not intended to be used unfilled.
This standard does not cover masonry units covered in EN 771-3.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 772-11, Methods of test for masonry units — Part 11: Determination of water absorption of aggregate
concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of
water absorption of clay masonry units
EN 772-14, Methods of tes
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.