EN ISO 11469:2000

Plastics - Generic identification and marking of plastics products (ISO 11469:2000)

Migrated from Progress Sheet (TC Comment) (2000-07-10): Changing of track further to TA (MG) requests - BP (970404): ++ From PQ/FV to VA/ISO ENQ+FV

Kunststoffe - Sortenspezifische Identifizierung und Kennzeichnung von Kunststoff-Formteilen (ISO 11469:2000)

Diese Internationale Norm legt ein System zur einheitlichen Kennzeichnung von Formteilen fest, die aus Kunststoffen hergestellt wurden. Maßnahmen bei der Durchführung des Kennzeichnungsvorgangs sind nicht Gegenstand dieser Norm. Anmerkung 1: Genaue Einzelheiten der Kennzeichnung, z.B. Mindestgröße des zu kennzeichnenden Gegenstandes, Größe der Beschriftung, die geeignete Anbringung der Kennzeichnung, dürfen durch Vereinbarung zwischen Hersteller und Verwender festgelegt werden.

Plastiques - Identification générique et marquage des produits en matière plastique (ISO 11469:2000)

La présente Norme internationale prescrit un système de marquage uniforme des produits en matière plastique. Elle exclut le (ou les) procédé(s) de marquage.NOTE : Les caractéristiques précises du marquage, telles que les dimensions minimales de l'article devant faire l'objet du marquage, les dimensions du lettrage et l'emplacement approprié auquel apposer le marquage, font l'objet d'un accord entre le fabricant et l'utilisateur.Le système de marquage est destiné à faciliter l'identification des produits en matière plastique dans l'optique de décisions à prendre ultérieurement en ce qui concerne leur manutention, leur valorisation en tant que déchets ou leur élimination.L'identification générique des plastiques est constituée par les symboles et abréviations donnés dans l'ISO 1043, parties 1 à 4.NOTE : Si l'on a besoin d'informations plus détaillées pour l'identification de la matière, on peut appliquer un marquage complémentaire sur le produit en matière plastique, conformément aux normes de produit pertinentes.La présente Norme internationale n'a pas pour objectif d'éliminer, de remplacer, ou d'interférer, de quelque manière que ce soit, avec les exigences relatives à l'étiquetage qui figurent dans les législations.

Polimerni materiali - Splošna identifikacija in označevanje polimernih proizvodov (ISO 11469:2000)

General Information

• Status: Withdrawn
• Publication Date: 14-May-2000
• Withdrawal Date: 18-Oct-2016
• ICS: 83.080.01 - Plastics in general
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 19-Oct-2016
• Ref Project: SIST EN ISO 11469:2001 - Plastics - Generic identification and marking of plastics products (ISO 11469:2000)

Relations

• Replaced By: EN ISO 11469:2016 - Plastics - Generic identification and marking of plastics products (ISO 11469:2016)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2001
3ROLPHUQLPDWHULDOL6SORãQDLGHQWLILNDFLMDLQR]QDþHYDQMHSROLPHUQLKSURL]YRGRY
,62
Plastics - Generic identification and marking of plastics products (ISO 11469:2000)
Kunststoffe - Sortenspezifische Identifizierung und Kennzeichnung von Kunststoff-
Formteilen (ISO 11469:2000)
Plastiques - Identification générique et marquage des produits en matiere plastique (ISO
11469:2000)
Ta slovenski standard je istoveten z: EN ISO 11469:2000
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 11469
Second edition
2000-05-15
Plastics — Generic identification and
marking of plastics products
Plastiques — Identification générique et marquage des produits en matière
plastique
Reference number
ISO 11469:2000(E)
©
ISO 2000
ISO 11469:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

ISO 11469:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 11469 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 1,
Terminology.
This second edition cancels and replaces the first edition (ISO 11469:1993). It includes additional generic
identification and marking requirements for plasticizers and flame retardants.
INTERNATIONAL STANDARD ISO 11469:2000(E)
Plastics — Generic identification and marking of plastics products
1 Scope
1.1 This International Standard specifies a system of uniform marking of products that have been fabricated from
plastics materials. Provision for the process or processes to be used for marking is outside the scope of this
standard.
NOTE Precise details of the marking, e.g. the minimum size of the item to be marked, the size of the lettering, the
appropriate location of the marking, are subject to agreement between the manufacturer and the user.
1.2 The marking system is intended to help identify plastics products for subsequent decisions concerning
handling, waste recovery or disposal.
1.3 Generic identification of the plastics is provided by the symbols and abbreviated terms given in ISO 1043,
parts 1 to 4.
NOTE If more detailed information for material identification is needed, additional marking of plastics products can be
applied as defined in the appropriate product standard.
1.4 This International Standard is not intended to supplant, replace or in any way interfere with requirements for
labelling found in legislation.
2 Normative references
The following normative documents contain provisions wh
...