EN 13353:2008
(Main)Solid wood panels (SWP) - Requirements
Solid wood panels (SWP) - Requirements
This European Standard specifies requirements for solid wood panels as defined in EN 12775 for use in dry, humid and exterior conditions as defined in service classes 1, 2 and 3 of EN 1995-1-1.
Additional information on supplementary properties for certain applications is also given.
Massivholzplatten (SWP) - Anforderungen
Diese Europäische Norm legt Anforderungen an Massivholzplatten, definiert nach EN 12775, zur Verwendung
im Trocken-, Feucht- und Außenbereich, definiert nach den Nutzungsklassen 1, 2 und 3 nach EN 1995-1-1,
fest.
Es werden zusätzliche Informationen über weitere Eigenschaften für bestimmte Verwendungszwecke angegeben.
Bois panneautés (SWP) - Exigences
La présente Norme européenne prescrit les exigences des bois panneautés tels que définis dans l’EN 12775
pour utilisation en milieux sec, humide et extérieur comme définis dans les classes de service 1, 2 et 3 de
l’EN 1995-1-1.
Des informations supplémentaires sur des caractéristiques complémentaires pour certaines applications sont
également données.
Masivne lesne plošče (SWP) - Zahteve
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Massivholzplatten (SWP) - AnforderungenBois panneautés (SWP) - ExigencesSolid wood panels (SWP) - Requirements79.060.99Other wood-based panelsICS:Ta slovenski standard je istoveten z:EN 13353:2008SIST EN 13353:2009en,fr,de01-april-2009SIST EN 13353:2009SLOVENSKI
STANDARDSIST EN 13353:20041DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13353November 2008ICS 79.060.99Supersedes EN 13353:2003
English VersionSolid wood panels (SWP) - RequirementsBois panneautés (SWP) - ExigencesMassivholzplatten (SWP) - AnforderungenThis European Standard was approved by CEN on 18 October 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13353:2008: ESIST EN 13353:2009
Properties for structural and non-structural applications.12 Bibliography.13
3 Foreword This document (EN 13353:2008) has been prepared by Technical Committee CEN/TC 112 “Wood-based panels”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the latest by May 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13353:2003.
Compared to EN 13353:2003 the following changes have been made: a) classification introduced according to non-structural use, structural use and declared values; b) information on moisture content of chemically or thermally treated wood added in 4.2; c) relationship between shear strength and wood failure percentage in introduced in 4.3.3; d) provisions for adhesives other than thermosetting for structural applications added in 4.3.4; e) different requirements for single and multi layer solid wood panels for structural applications specified in 4.5.2; f) footnote regarding alternative test methods for the determination of the bonding quality added in Table 5. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Den-mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
5 EN 12775, Solid wood panels — Classification and terminology EN 12871, Wood-based panels — Performance specifications and requirements for load bearing boards for use in floors, walls and roofs EN 13017-1, Solid wood panels — Classification by surface appearance — Part 1: Softwood EN 13017-2, Solid wood panels — Classification by surface appearance — Part 2: Hardwood EN 13183-2, Moisture content of a piece of sawn timber — Part 2: Estimation by electrical resistance method EN 13354, Solid wood panels — Bonding quality — Test method EN 13446, Wood-based panels — Determination of withdrawal capacity of fasteners EN 13986, Wood-based panels for use in construction — Characteristics, evaluation of conformity and marking EN 15416-3, Adhesives for load bearing timber structures other than phenolic and aminoplastic — Test methods — Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in bending shear 3 Terms, definitions and classes 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12775 and the following apply. 3.1.1 solid wood panel for use in dry conditions panel intended for use in interior applications with no risk of wetting as defined in service class 1 of EN 1995-1-1 and use class 1 of EN 335-2 NOTE Service class 1 is characterised by a moisture content of the material corresponding to a temperature of 20 °C and a relative humidity of the surrounding air exceeding 65 % for only a few weeks per year. 3.1.2 solid wood panel for use in humid conditions panel intended for use in protected external applications as defined in service class 2 of EN 1995-1-1 (e. g. behind cladding or under roof coverings) and use class 2 of EN 335-2 NOTE 1 It is also capable of resisting weather exposure for short periods (e.g. when exposed during construction). NOTE 2 Service class 2 is characterised by a moisture content of the material corresponding to a temperature of 20 °C and a relative humidity of the surrounding air exceeding 85 % for only a few weeks per year. 3.1.3 solid wood panel for use in exterior conditions panel intended for use in unprotected external applications as defined in service class 3 of EN 1995-1-1 and use class 3 of EN 335-2 NOTE 1 It is also capable of withstanding exposure to weathering conditions and liquid water, or water vapour in a damp but ventilated location where it can frequently attain a moisture content above 20 %. NOTE 2 Service class 3 is characterised by a moisture content of the material higher than service class 2. 3.2 Classes for solid wood panels indicating their intended use 3.2.1 Technical classes for non-structural use SWP/1 NS: Solid wood panel for non-structural use in dry conditions according to 3.1.1 SIST EN 13353:2009
nominal thickness Edge straightness Squareness ± 2,0 mm 0,5 mm ± 1,0 mm 1,0 mm/m 1,0 mm/m a Determined in accordance with EN 324-1 b Determined in accordance with EN 324-2
4.2 Moisture content at despatch At time of despatch the moisture content according to EN 322 shall be (8 ± 2) % for use in dry conditions, (10 ± 3) % for use in humid conditions and (12 ± 3) % for use in exter
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.