iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13146-1:2002

(Main)

Railway applications - Track - Test methods for fastening systems - Part 1: Determination of longitudinal rail restraint

Railway applications - Track - Test methods for fastening systems - Part 1: Determination of longitudinal rail restraint

This part of EN 13146 specifies a laboratory test procedure to determine the maximum axial load that can be applied to a rail, secured to a sleeper by a railfastening assembly, without non-elastic displacement of the rail occurring. Performance requirements based on this test method are included in EN 13481-2.

Bahnanwendungen - Oberbau - Prüfverfahren für Schienenbefestigungssysteme - Teil 1: Ermittlung des Durchschubwiderstandes in Längsrichtung

Dieser Teil der Normenreihe EN 13146 legt ein Laborprüfverfahren zur Bestimmung der maximalen Längs-kraft fest, die auf eine Schiene, die mittels eines Schienenbefestigungssystems auf einer Schwelle, auf einem Lager oder auf einer Betonplatte befestigt ist, aufgebracht werden kann, bevor eine bleibende Verschiebung der Schiene eintritt.
Dieses Prüfverfahren gilt für ein komplettes Schienenbefestigungssystem.

Applications ferroviaires - Voie - Méthodes d'essai pour les systèmes de fixation - Partie 1: Détermination de la résistance longitudinale au glissement

La présente partie de la présente Norme européenne prescrit une méthode d'essai en laboratoire permettant de déterminer la charge axiale maximale pouvant être appliquée à un rail fixé à une traverse, un support ou un élément de voie sur dalle au moyen d'un système de fixation, sans qu'il se produise un déplacement irréversible du rail.
Cette méthode d'essai s'applique à un ensemble de fixation complet.

Železniške naprave – Zgornji ustroj – Preskušanje pritrdilnih sistemov – 1. del: Ugotavljanje vzdolžnega odpora

General Information

Status
Withdrawn
Publication Date
19-Nov-2002
Withdrawal Date
03-Apr-2012
ICS
93.100 - Construction of railways
Technical Committee
CEN/TC 256 - Railway applications
Drafting Committee
CEN/TC 256/SC 1/WG 17 - Fastening systems
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
04-Apr-2012
Completion Date
04-Apr-2012
Directive
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
96/48/EC - Interoperability of the trans-European high-speed rail system
Mandate
M/024 - Mandate to CEN/CENELEC/ETSI for programming and standardization in the field of railway equipment
M/275 - Mandate to CEN/CENELEC/ETSI for standardization in the field of railway equipment on the interoperability of the Trans-European high-speed rail system
Ref Project
SIST EN 13146-1:2004 - Railway applications - Track - Test methods for fastening systems - Part 1: Determination of longitudinal rail restraint

Relations

Replaced By
EN 13146-1:2012 - Railway applications - Track - Test methods for fastening systems - Part 1: Determination of longitudinal rail restraint
Effective Date
06-Jun-2009

Buy Standard

EN 13146-1:2004EN 13146-1:2004
PreviousNext
Standard
EN 13146-1:2004
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13146-1:2004
01-marec-2004
Železniške naprave – Zgornji ustroj – Preskušanje pritrdilnih sistemov – 1. del:
Ugotavljanje vzdolžnega odpora
Railway applications - Track - Test methods for fastening systems - Part 1:
Determination of longitudinal rail restraint
Bahnanwendungen - Oberbau - Prüfverfahren für Schienenbefestigungssysteme - Teil 1:
Ermittlung des Durchschubwiderstandes in Längsrichtung
Applications ferroviaires - Voie - Méthodes d'essai pour les systemes de fixation - Partie
1: Détermination de la résistance longitudinale au glissement
Ta slovenski standard je istoveten z: EN 13146-1:2002
ICS:
93.100 Gradnja železnic Construction of railways
SIST EN 13146-1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13146-1:2004

---------------------- Page: 2 ----------------------

SIST EN 13146-1:2004
EUROPEAN STANDARD
EN 13146-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2002
ICS 93.100
English version
Railway applications - Track - Test methods for fastening
systems - Part 1: Determination of longitudinal rail restraint
Applications ferroviaires - Voie - Méthodes d'essai pour les Bahnanwendungen - Oberbau - Prüfverfahren für
systèmes de fixation - Partie 1: Détermination de la Schienenbefestigungssysteme - Teil 1: Ermittlung des
résistance longitudinale au glissement Durchschubwiderstandes in Längsrichtung
This European Standard was approved by CEN on 2 October 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13146-1:2002 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13146-1:2004
EN 13146-1:2002 (E)
Contents
page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions, symbols and abbreviations.4
3.1 Terms and definitions.4
3.2 Symbols and abbreviations .4
4 Principle.4
5 Apparatus .4
5.1 Rail.4
5.2 Loading equipment.5
5.3 Load-displacement measuring and recording instruments .5
5.3.1 General.5
5.3.2 Verification of calibration.5
6 Test specimens .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 16843:2024(Main)
Railway applications - Infrastructure - Mechanical requirements for joints in running rails
SIST EN 16843:2024

This European Standard deals with mechanical rail joints for flat bottom rails 46 kg/m and over. The scope of this standard is: to
establish requirements for insulated and non-insulated rail joints, for stressed rail (continuous welded rail, CWR) and unstressed rail (jointed track); to define mechanical and electrical requirements for type approval and for acceptance of insulated rail joints which are manufactured in a factory (prefab construction) as well as assembled onsite (site construction). This standard specifies the minimum requirements. Special applications as for instance tram systems may require different demands in certain paragraphs and should be agreed between customer and supplier. The scope also excludes expansion joints (it is covered in EN 13232-8), and special joints in switch constructions.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-2:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 2: Intrinsic characteristics - Airborne sound insulation under diffuse sound field conditions
SIST EN 16272-2:2024

This document specifies the laboratory method for measuring the airborne sound insulation performance of railway noise barriers in reverberant conditions. It covers the assessment of the intrinsic performance of noise barriers and related devices acting on airborne sound propagation that can reasonably be assembled inside the testing facility described in EN ISO 10140 2 and EN ISO 10140 4.
This method is not intended for the determination of the intrinsic characteristics of airborne sound insulation of noise barriers to be installed on railway in non-reverberant conditions.
All noise reducing devices different from noise barriers and related devices acting on airborne sound propagation, e.g. devices for attenuation of ground borne vibration and on board devices, are out of the scope of this document.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-5:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 5: Intrinsic characteristics - Sound absorption under direct sound field conditions
SIST EN 16272-5:2024

This document describes a test method for measuring a quantity representative of the intrinsic characteristics of sound absorption from railway noise barriers and related devices acting on airborne sound propagation, the sound reflection index RI, and then calculate a single-number rating for sound absorption from it.
The test method is intended for the following applications:
-   determination of the intrinsic characteristics of sound absorption of noise barriers and related devices acting on airborne sound propagation to be installed along railways, to be measured either on typical installations alongside railways or on a relevant sample section;
-   determination of the intrinsic characteristics of sound absorption of noise barriers and related devices acting on airborne sound propagation in actual use under direct sound field conditions;
-   comparison of design specifications with actual performance data after the completion of the construction work;
-   verification of the long-term performance of noise barriers and related devices acting on airborne sound propagation (with a repeated application of the method).
The test method is not intended for the following applications:
-   determination of the intrinsic characteristics of sound absorption of noise barriers and related devices acting on airborne sound propagation to be installed in reverberant conditions, e.g. inside tunnels or deep trenches.
Results for the sound reflection index are expressed as a function of frequency, in one-third octave bands, where possible, between 100 Hz and 5 kHz. If it is not possible to get valid measurements results over the whole frequency range indicated, the results are given in a restricted frequency range and the reasons of the restriction(s) are clearly reported.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-1:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 1: Intrinsic characteristics - Sound absorption under diffuse sound field conditions
SIST EN 16272-1:2024

This European Standard specifies the laboratory method for measuring the sound absorption performance of railway noise barriers and related devices acting on airborne sound propagation in reverberant conditions. It covers the assessment of the intrinsic sound absorption performance of devices that can reasonably be assembled inside the testing facility described in EN ISO 354.
This method is not intended for the determination of the intrinsic characteristics of sound absorption of noise barriers and related devices acting on airborne sound propagation to be installed on railways in non-reverberant conditions.
The test method in EN ISO 354 referred to in this European Standard excludes devices that act as weakly damped resonators. Some devices will depart significantly from these requirements and in these cases, care is needed in interpreting the results.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-6:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 6: Intrinsic characteristics - Airborne sound insulation under direct sound field conditions
SIST EN 16272-6:2024

This document describes a test method for measuring a quantity representative of the intrinsic characteristics of airborne sound insulation for rail noise barriers and related devices: the sound insulation index.
The test method is intended for the following applications:
-   determination of the intrinsic characteristics of airborne sound insulation of noise barriers and related devices to be installed along railways, to be measured either on typical installations alongside railways or in laboratory conditions;
-   determination of the intrinsic characteristics of airborne sound insulation of noise barriers and related devices in actual use;
-   comparison of design specifications with actual performance data after the completion of the construction work;
-   verification of the long-term performance of noise barriers and related devices (with a repeated application of the method);
-   interactive design process of new products, including the formulation of installation manuals.
The test method is not intended for the determination of the intrinsic characteristics of airborne sound insulation of noise barriers and related devices to be installed in reverberant conditions, e.g. inside tunnels or deep trenches or under covers.
Results are expressed as a function of frequency in one-third octave bands, where possible, between 100 Hz and 5 kHz. If it is not possible to get valid measurement results over the whole frequency range indicated, the results need to be given in a restricted frequency range and the reasons for the restriction(s) need to be clearly reported.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13231-1:2023(Main)
Railway applications - Track - Acceptance of works - Part 1: Works on ballasted track - Plain line, switches and crossings
SIST EN 13231-1:2024

This document specifies technical requirements and tolerances for the acceptance of works on ballasted track situated on:
-   plain line;
-   switches and crossings; and
-   rail expansion devices as part of the track
for 1 435 mm and wider track gauge railways.
The works on ballasted track, hereafter referred to as track works, concern construction of new track, track renewal and track maintenance.
This document specifies the requirements for substructure works, track geometry, absolute track position, working parameters of on track machines, track components, ballast cross section, structure gauge, stressing works, specific measurements and quality checks for switches and crossings and rail expansion devices, and for the measuring systems used to perform measurements, verifications and checks for the scope of acceptance. Requirements for responsibilities and documentation necessary for the acceptance of track works are specified.
This document also requires compliance of all track materials with the customer’s relevant acceptance criteria and specifications provided by the supplier.
This document does not cover works related to reprofiling the railhead or the associated measurements, except for some measurements related to safety, as these works are covered by other parts of EN 13231 series.
Platform reconstruction works and level crossing works are not covered by this document.
This document does not apply to urban rail systems or ballastless track.

  • Standard
    90 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-3-2:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 3-2: Normalized railway noise spectrum and single number ratings for direct sound field applications
SIST EN 16272-3-2:2023

This document specifies a normalized railway noise spectrum for the evaluation and assessment of the acoustic performance of devices designed to reduce airborne railway noise near railways.
All noise reducing devices different from noise barriers and related devices acting on airborne sound propagation, e.g. devices for attenuation of ground borne vibration and on board devices are outside of the scope of this document.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16272-3-1:2023(Main)
Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 3-1: Normalized railway noise spectrum and single number ratings for diffuse sound field applications
SIST EN 16272-3-1:2023

This document specifies a normalized railway noise spectrum for the evaluation and assessment of the acoustic performance of devices designed to reduce airborne railway noise near railways.
All noise reducing devices different from noise barriers and related devices acting on airborne sound propagation, e.g. devices for attenuation of ground borne vibration and on board devices are outside of the scope of this document.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13232-1:2023(Main)
Railway applications - Track - Switches and crossings for Vignole rails - Part 1: Definitions
SIST EN 13232-1:2023

This European Standard provides an accepted "terminology" for switch and crossing work. With the assistance of diagrams, the various components are given definitions, and these specific names are regarded as obligatory.
The definitions cover the constituent parts and design geometry of switch and crossing work, and include the movement of switches. Additional terminology of a more specific nature will be defined in the relevant part of the series.
The present definitions set out the terms most generally used for the geometrical form and the construction of switches and crossings, omitting those of too special a nature.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13232-6:2023(Main)
Railway applications - Track - Switches and crossings for Vignole rails - Part 6: Fixed common and obtuse crossings
SIST EN 13232-6:2023

This document:
—   Establish a working terminology for fixed crossings and their constituent parts, and identifies the main types;
—   specifies the different and varying ways by which crossings can be described using the following parameters:
—   geometry of the crossing;
—   types of construction;
—   design criteria;
—   manufacturing processes;
—   tolerances and inspection.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day