EN 13880-4:2024

Hot applied joint sealants - Part 4: Test method for the characterization of heat resistance - Change in penetration value

This document specifies a method to characterize the heat resistance on samples of hot applied joint sealants according to EN 14188 1 by comparing the cone penetration and resilience values before and after exposure.

Heiß verarbeitbare Fugenmassen - Teil 4: Prüfverfahren zur Bestimmung der Wärmebeständigkeit - Änderung der Konus-Penetration

Dieses Dokument legt ein Verfahren zur Charakterisierung der Wärmebeständigkeit von Proben von heiß verarbeitbaren Fugenmassen nach EN 14188 1 durch Vergleich der Werte von Konus-Penetration und Rückstellvermögen vor und nach der Exposition fest.

Produits de scellement de joints appliqués à chaud - Partie 4 : Méthode d'essai pour la détermination de la résistance à la chaleur - Variation de la pénétrabilité

Ce document spécifie une méthode pour caractériser la résistance à la chaleur sur des échantillons de mastics de joints appliqués à chaud selon l’EN 14188 1 en comparant les valeurs de pénétration du cône et de résilience avant et après exposition.

Tesnilne mase za stike, ki se vgrajujejo po vročem postopku - 4. del: Preskusna metoda za karakterizacijo odpornosti proti toploti - Sprememba penetracije

Ta dokument opisuje metodo za karakterizacijo odpornosti proti povišani temperaturi vzorcev tesnilnih mas za stike, ki se vgrajujejo po vročem postopku, v skladu s standardom EN 14188-1 s primerjavo penetracije s stožcem in vrednosti odpornosti pred izpostavljanjem in po njem.

General Information

• Status: Published
• Publication Date: 20-Aug-2024
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CEN/TC 227 - Road materials
• Drafting Committee: CEN/TC 227/WG 3 - Materials for concrete roads including joint fillers and sealants
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 21-Aug-2024
• Due Date: 15-Aug-2024
• Completion Date: 21-Aug-2024
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Mandate: M/124 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on road construction products
• Ref Project: SIST EN 13880-4:2024 - Hot applied joint sealants - Part 4: Test method for the characterization of heat resistance - Change in penetration value

Relations

• Replaces: EN 13880-4:2003 - Hot applied joint sealants - Part 4: Test method for the determination of heat resistance - Change in penetration value
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2024
Nadomešča:
SIST EN 13880-4:2004
Tesnilne mase za stike, ki se vgrajujejo po vročem postopku - 4. del: Preskusna
metoda za karakterizacijo odpornosti proti toploti - Sprememba penetracije
Hot applied joint sealants - Part 4: Test method for the characterization of heat
resistance - Change in penetration value
Heiß verarbeitbare Fugenmassen - Teil 4: Prüfverfahren zur Bestimmung der
Wärmebeständigkeit - Änderung der Konus-Penetration
Produits de scellement de joints appliqués à chaud - Partie 4 : Méthode d'essai pour la
détermination de la résistance à la chaleur - Variation de la pénétrabilité
Ta slovenski standard je istoveten z: EN 13880-4:2024
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13880-4
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2024
EUROPÄISCHE NORM
ICS 93.080.20 Supersedes EN 13880-4:2003
English Version
Hot applied joint sealants - Part 4: Test method for the
characterization of heat resistance - Change in penetration
value
Produits de scellement de joints appliqués à chaud - Heiß verarbeitbare Fugenmassen - Teil 4:
Partie 4 : Méthode d'essai pour la détermination de la Prüfverfahren zur Bestimmung der
résistance à la chaleur - Variation de la pénétrabilité Wärmebeständigkeit - Änderung der Konus-
Penetration
This European Standard was approved by CEN on 24 June 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13880-4:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 6
6 Procedure . 6
6.1 General. 6
6.2 Exposure at elevated temperature . 6
6.3 Cone penetration. 6
6.4 Penetration and recovery (resilience) . 6
6.5 Test conditions for storage at elevated temperature . 6
6.6 Conditioning after storage at elevated temperature . 6
7 Expression of results . 6
8 Precision . 7
9 Test report . 7
Bibliography . 8
European foreword
This document (EN 13880-4:2024) has been prepared by Technical Committee CEN/TC 227 “Road
materials”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2025, and conflicting national standards shall
be withdrawn at the latest by February 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13880-4:2003.
— clarification of the test to improve the performance of the test method.
This document is one part of the EN 13880 series of standards, Hot applied joint sealants, which consists
of the following parts:
— Part 1: Test method for the determination of density at 25 °C.
— Part 2: Test method for the determination of cone penetration at 25 °C.
— Part 3: Test method for the determination of penetration and recovery (resilience).
— Part 4: Test method for the determination of heat resistance — Change in penetration value.
— Part 5: Test method for the determination of flow resistance.
— Part 6: Method for the preparation of samples for testing.
— Part 7: Function testing of joint sealants.
— Part 8: Test method for the determination of the change in weight of fuel resistance joint sealants after
fuel immersion.
— Part 9: Test method for the determination
...