Curtain walling - Product standard

This European Standard specifies requirements of curtain walling kit intended to be used as a building envelope to provide weather resistance, safety in use and energy economy and heat retention and provides test/assessments/calculation methods and compliance criteria of the related performances.
The curtain walling kit covered by this standard should fulfil its own integrity and mechanical stability but does not contribute to the load bearing or stability of the main building structure, and could be replaced independently of it.
This standard applies to curtain walling kit ranging from a vertical position to ± 15° from the vertical. Any sloping parts should be contained within the curtain walling kit.
This standard is applicable to the whole of the curtain walling kits, including the fixings.
Curtain walling according to this standard is intended to be used as part of the building envelope.
This European Standard does not include:
—   “Patent glazing” (glazed sloping roofs) kits;
—   Roof glazing constructions;
—   Façades made of precast concrete panels as part of the wall (see EN 14992).
NOTE 1   Precast concrete panels may be used in curtain walling kits as infill panels.
NOTE 2   Durability of structural sealed glazing infills is not covered by this standard.

Vorhangfassaden - Produktnorm

Diese Europäische Norm legt die Anforderungen an Vorhangfassadenbausätze fest, die zur Verwendung als Gebäude¬hülle vorgesehen sind, um Witterungsbeständigkeit, Nutzungssicherheit, Energieeinsparung und Wärmeschutz zu ermöglichen, und enthält Prüf /Bewertungs /Berechnungsverfahren und Konformitäts¬kriterien für die entsprechenden Leistungen.
Eine Vorhangfassade nach dieser Norm verfügt über ihre eigene mechanische Stabilität und Standsicherheit, sie trägt aber nicht zur Lastabtragung oder Stabilität des Hauptbaukörpers bei und kann unabhängig von diesem ersetzt werden.
Diese Norm gilt für Vorhangfassadenbausätze, die von einer vertikalen Konstruktion bis hin zu Konstruktionen mit einer Neigung von bis zu ±15° von der Vertikalen reichen. Jegliche geneigten Teile sollten im Vorhangfassadenbausatz eingeschlossen sein.
Diese Norm gilt für den gesamten Vorhangfassadenbausatz einschließlich der Befestigungsmittel.
Vorhangfassaden nach dieser Norm sind zur Verwendung als Teil der Gebäudehülle vorgesehen.
Diese Europäische Norm gilt nicht für:
- Bausätze für „Patentverglasungen“ (Schrägdachverglasungen);
- Konstruktionen von Dachverglasungen;
- Fassaden aus Fertigbetonelementen als Teil der Wand (siehe EN 14992).
ANMERKUNG 1 Fertigbetonelemente dürfen in Vorhangfassadenbausätzen als Ausfachungspaneele verwendet werden.
ANMERKUNG 2 Die Dauerhaftigkeit von Ausfachungen aus geklebten Glaskonstruktionen ist nicht Gegenstand dieser Norm.

Façades rideaux - Norme de produit

La présente Norme européenne spécifie les exigences applicables au kit de façades-rideaux destiné à être utilisé comme une enveloppe du bâtiment afin de fournir une résistance aux sollicitations climatiques, une sécurité d'utilisation, de l'économie d'énergie et d’isolation thermique et fournit également des méthodes d’essai/d’évaluation/de calcul et des critères de conformité des performances associées.  
Le kit de façade rideau couvert par la présente norme doit contribuer à sa propre intégrité et stabilité, mais sans contribuer à la résistance ou à la stabilité de la structure du bâtiment et pourrait être remplacé de manière indépendante.
La présente norme s’applique au kit de façade rideau variant de la position verticale à une position inclinée de ± 15° par rapport à la verticale. Il convient que toutes pièces inclinées soient contenues dans le kit de façade rideau.
La présente norme s'applique à l'intégralité des kits de façades rideaux, y compris les points d'attache.
Conformément à la présente norme, une façade rideau est conçue pour être utilisée comme une partie de l’enveloppe du bâtiment.
La présente Norme européenne n’inclut pas :
   des kits de systèmes de vitrages auto-drainant à joint secs (toits inclinés vitrés) ;
   des verrières ;
   façades constituées de panneaux en béton préfabriqués faisant partie du mur (voir l'EN 14992).
NOTE 1   Les panneaux de béton préfabriqués peuvent être utilisés dans les kits de façades rideaux comme panneaux de remplissage.
NOTE 2   Durabilité des remplissages de vitrage collés (VEC) ne sont pas couverts par cette norme.

Obešene fasade - Standard za proizvod

General Information

Status
Published
Publication Date
26-May-2020
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
06-Dec-2021

Relations

Effective Date
18-Jan-2023

Buy Standard

Standard
EN 13830:2015+A1:2020
English language
90 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2020
Nadomešča:
SIST EN 13830:2015
Obešene fasade - Standard za proizvod
Curtain walling - Product standard
Vorhangfassaden - Produktnorm
Façades rideaux - Norme de produit
Ta slovenski standard je istoveten z: EN 13830:2015+A1:2020
ICS:
91.060.10 Stene. Predelne stene. Walls. Partitions. Facades
Fasade
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13830:2015+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2020
EUROPÄISCHE NORM
ICS 91.060.10 Supersedes EN 13830:2015
English Version
Curtain walling - Product standard
Façades rideaux - Norme de produit Vorhangfassaden - Produktnorm
This European Standard was approved by CEN on 7 February 2015 and includes Amendment 1 approved by CEN on 7 October
2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13830:2015+A1:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 6
Introduction . 7
1 Scope . 8
2 Normative references . 8
3 Terms, definitions and abbreviated terms . 12
3.1 Definitions . 12
3.2 Abbreviations used in this standard . 14
4 Product characteristics . 14
4.1 Reaction to fire (of components, when relevant) . 14
4.2 Fire resistance . 15
4.3 Fire propagation (to upper levels) . 15
4.4 Watertightness . 15
4.5 Resistance to its own dead load . 15
4.6 Wind load resistance . 15
4.7 Resistance to snow load (only for elements subjected to snow load). 16
4.8 Impact resistance . 16
4.8.1 General . 16
4.8.2 Internal . 16
4.8.3 External . 16
4.9 Resistance to live horizontal loads at sill level . 16
4.10 Seismic resistance . 16
4.10.1 General . 16
4.10.2 Safety in use. 17
4.10.3 Serviceability (where specially required) . 17
4.11 Thermal shock resistance . 17
4.12 Direct airborne sound insulation . 17
4.13 Flanking sound transmission . 17
4.14 Thermal transmittance . 17
4.15 Air permeability . 17
4.16 Water vapour permeability . 17
4.17 Radiation properties . 18
4.18 Durability . 18
4.18.1 General . 18
4.18.2 Durability of watertightness . 18
4.18.3 Durability of thermal transmittance . 18
4.18.4 Durability of air permeability . 18
5 Testing, assessment and sampling methods . 19
5.1 Sampling . 19
5.1.1 General . 19
5.1.2 Sequence of testing . 19
5.2 Reaction to fire (of components, when relevant) . 20
5.3 Fire resistance . 20
5.4 Fire propagation (to upper levels) . 20
5.5 Watertightness . 20
5.6 Resistance to its own dead load . 20
5.7 Wind load resistance . 21
5.8 Resistance to snow load (only for elements subject to snow load) . 21
5.9 Impact resistance. 21
5.10 Resistance to live horizontal loads at sill level . 22
5.11 Seismic resistance . 22
5.11.1 Safety in use . 22
5.11.2 Serviceability (where specially required) . 22
5.12 Direct airborne sound insulation . 22
5.13 Flanking sound transmission . 22
5.14 Thermal transmittance. 22
5.15 Air permeability . 23
5.16 Radiation properties . 23
5.17 Durability. 23
5.17.1 General . 23
5.17.2 Durability of watertightness . 23
5.17.3 Durability of thermal transmittance . 24
5.17.4 Durability of air permeability . 24
6 Assessment and verification of constancy of performance (AVCP) . 25
6.1 General . 25
6.2 Type testing . 25
6.2.1 General . 25
6.2.2 Test samples, testing and compliance criteria . 26
6.2.3 Test reports . 27
6.2.4 Cascading determination of the product type results . 27
6.3 Factory production control (FPC) . 28
6.3.1 General . 28
6.3.2 Requirements . 29
6.3.3 Product specific requirements . 32
6.3.4 Initial inspection of factory and of FPC . 32
6.3.5 Continuous surveillance of FPC (only for curtain walling kits covered by AVCP
system 1) . 33
6.3.6 Procedure for modifications . 33
6.3.7 One-off products, pre-production products (e.g. prototypes) and products produced
in very low quantity .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.