EN ISO 7823-3:2007
(Main)Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 3: Continuous cast sheets (ISO 7823-3:2007)
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 3: Continuous cast sheets (ISO 7823-3:2007)
ISO 7823-3:2007 specifies requirements for non-modified flat poly(methyl methacrylate) (PMMA) continuous cast sheets for general-purpose use. The sheets may be colourless or coloured, and may be transparent, translucent or opaque.
The thickness range of the sheets covered by this part of ISO 7823 is 1 mm to 10 mm.
Kunststoffe - Tafeln aus Polymethylmethacrylat - Typen, Maße und Eigenschaften - Teil 3: Endlosprodukte (ISO 7823-3:2007)
Dieser Teil von ISO 7823 legt die Anforderungen an flache (durch Stranggießen hergestellte) Endlosprodukte (Platten) aus unmodifiziertem Polymethylmethacrylat (PMMA) für allgemeine Zwecke fest. Die Tafeln dürfen farblos oder gefärbt und durchsichtig, durchscheinend oder undurchsichtig sein.
Der Dickenbereich der in diesem Teil der ISO 7823 behandelten Tafeln beträgt 1 mm bis 10 mm.
Plastiques - Plaques en poly(méthacrylate de méthyle) - Types, dimensions et caractéristiques - Partie 3: Plaques coulées continues (ISO 7823-3:2007)
L'ISO 7823-3:2007 spécifie des exigences relatives aux plaques coulées continues en poly(méthacrylate de méthyle) (PMMA), planes et non modifiées, pour usage général. Ces plaques peuvent être incolores ou colorées, et transparentes, translucides ou opaques.
La plage de l'épaisseur des plaques relevant de l'ISO 7823-3:2007 est comprise entre et 1 mm et 10 mm.
Polimerni materiali - Plošče iz polimetilmetakrilata - Vrste, mere in značilnosti - 3. del: Kontinuirno lite plošče (ISO 7823-3:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2007
1DGRPHãþD
SIST EN ISO 7823-3:2004
3ROLPHUQLPDWHULDOL3ORãþHL]SROLPHWLOPHWDNULODWD9UVWHPHUHLQ]QDþLOQRVWL
GHO .RQWLQXLUQROLWHSORãþH ,62
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics -
Part 3: Continuous cast sheets (ISO 7823-3:2007)
Kunststoffe - Tafeln aus Polymethylmethacrylat - Typen, Maße und Eigenschaften - Teil
3: Endlosprodukte (ISO 7823-3:2007)
Plastiques - Plaques en poly(méthacrylate de méthyle) - Types, dimensions et
caractéristiques - Partie 3: Plaques coulées continues (ISO 7823-3:2007)
Ta slovenski standard je istoveten z: EN ISO 7823-3:2007
ICS:
83.140.10 Filmi in folije Films and sheets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 7823-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2007
ICS 83.140.10 Supersedes EN ISO 7823-3:2004
English Version
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions
and characteristics - Part 3: Continuous cast sheets (ISO 7823-
3:2007)
Plastiques - Plaques en poly(méthacrylate de méthyle) - Kunststoffe - Tafeln aus Polymethylmethacrylat - Typen,
Types, dimensions et caractéristiques - Partie 3: Plaques Maße und Eigenschaften - Teil 3: Endlosprodukte (ISO
coulées continues (ISO 7823-3:2007) 7823-3:2007)
This European Standard was approved by CEN on 23 April 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7823-3:2007: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 7823-3:2007) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by November 2007, and conflicting national
standards shall be withdrawn at the latest by November 2007.
This document supersedes EN ISO 7823-3:2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
Endorsement notice
The text of ISO 7823-3:2007 has been approved by CEN as EN ISO 7823-3:2007 without any
modifications.
INTERNATIONAL ISO
STANDARD 7823-3
Second edition
2007-05-15
Plastics — Poly(methyl methacrylate)
sheets — Types, dimensions and
characteristics —
Part 3:
Continuous cast sheets
Plastiques — Plaques en poly(méthacrylate de méthyle) — Types,
dimensions et caractéristiques —
Partie 3: Plaques coulées continues
Reference number
ISO 7823-3:2007(E)
©
ISO 2007
ISO 7823-3:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 7823-3:2007(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Composition . 2
5 General requirements. 2
6 Test methods. 6
7 Retest and rejection. 7
Annex A (normative) Determination of dimensional change on heating (shrinkage). 8
ISO 7823-3:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7823-3 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This second edition cancels and replaces the first edition (ISO 7823-3:2003), which has been technically
revised.
ISO 7823 consists of the following parts, under the general title Plastics — Poly(methyl methacrylate)
sheets — Types, dimensions and characteristics:
⎯ Part 1: Cast sheets
⎯ Part 2: Extruded sheets
⎯ Part 3: Continuous cast sheets
iv © ISO 2007 – All rights reserved
INTERNATIONAL STANDARD ISO 7823-3:2007(E)
Plastics — Poly(methyl methacrylate) sheets — Types,
dimensions and characteristics —
Part 3:
Continuous cast sheets
1 Scope
This part of ISO 7823 specifies requirements for non-modified flat poly(methyl methacrylate) (PMMA)
continuous cast sheets for general-purpose use. The sheets may be colourless or coloured, and may be
transparent, translucent or opaque.
The thickness range of the sheets covered by this part of ISO 7823 is 1 mm to 10 mm.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 62:1999, Plastics — Determination of water absorption
ISO 75-2:2004, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and
ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 306:2004, Plastics — Thermoplastics materials — Determination of Vicat softening temperature (VST)
ISO 489:1999, Plastics — Determination of refractive index
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 877, Plastics — Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and
to intensified weathering by daylight using Fresnel mirrors
ISO 1183-1:2004, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient
column method
ISO 2039-2, Plastics — Determination of hardness — Part 2: Rockwell hardness
ISO 7823-3:2007(E)
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection
ISO 4582, Plastics — Determination of changes in colour and variations in properties after exposure to
daylight under glass, natural weathering or laboratory light sources
ISO 4892-2:2006, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ISO 4892-4, Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc
lamps
ISO 11359-2, Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear
thermal expansion and glass transition temperature
ISO 13468-1, Plastics — Determination of the total luminous transmittance of transparent materials — Part 1:
Single-beam instrument
ISO 13468-2, Plastics — Determination of the total luminous transmittance of transparent materials — Part 2:
Double-beam instrument
ISO 14782, Plastics — Determination of haze for transparent materials
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
non-modified cast PMMA sheets
sheets based on homopolymers of MMA, or copolymers of MMA with acrylic or methacrylic monomers,
produced by bulk polymerization in the presence of suitable initiators
3.2
flat PMMA sheets
sheets with two plane, substantially parallel surfaces
4 Composition
The amounts of plasticizing ingredients (materials that do not undergo chemical reaction to become a part of
the polymer), other monomers and crosslinking agents (materials that produce the links between the chains of
polymers) present shall be such that the basic properties are not changed from the values given in Table 3.
These amounts are in most cases less than a mass fraction of 5 %.
Other additives, e.g. colorants, UV absorbers and pigments, may be included to give specific properties.
National environmental legislation and regulations shall be followed regarding additives.
5 General requirements
5.1 Protective coverings
Unless otherwise agreed upon by the interested parties, the surfaces of the sheet, as delivered, shall be
protected by suitable materials, for example kraft paper secured with a water-soluble or pressure-sensitive
adhesive, or a polyethylene film, which are readily removable without causing surface contamination or
damage.
2 © ISO 2007 – All rights reserved
ISO 7823-3:2007(E)
5.2 Appearance
5.2.1 Surface defects
The sheet shall have a smooth surface. There shall be no scratches, marks or other surface defects larger
than 3 mm each anywhere in the sheet.
5.2.2 Inclusion defects
There shall be no bubbles, inclusions, cracks or other defects that could adversely affect the performance of
the sheet in its intended application which are larger than 3 mm each anywhere in the sheet.
5.2.3 Classification of defects
The area of any defect found in the sheets shall be classified as specified in Table 1. Each defect shall be
considered separately.
Table 1 — Classification of defects
Classification Area of surface defect Area of inclusion defect
2 2
Less than 1 mm Less than 1 mm
Negligible
2 2 2 2
Acceptable 1 mm to 3 mm 1 mm to 3 mm
5.2.4 Distribution of defect
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.