Bituminous mixtures - Test methods - Part 34: Marshall test

This document specifies a test method for determining the stability, flow and the Marshall quotient values of specimens of bituminous mixtures mixed according to EN 12697-35 and prepared using the impact compactor method of test EN 12697-30. It is limited to dense graded asphalt concrete and hot rolled asphalt.

Asphalt - Prüfverfahren - Teil 34: Marshall-Prüfung

Diese Europäische Norm legt ein Prüfverfahren zur Bestimmung von Stabilität, Fließwert und Marshall-Quotient von Probekörpern aus nach EN 12697 35 gemischtem Asphalt, die mit einem Marshall-Verdichtungsgerät nach EN 12697 30 hergestellt wurden, fest. Das Prüfverfahren gilt nur für dichten Asphaltbeton und Hot-Rolled-Asphalt.

Mélanges bitumineux - Méthodes d'essai - Partie 34 : Essai Marshall

La présente Norme européenne spécifie une méthode d'essai pour déterminer la stabilité, le fluage et les valeurs du quotient Marshall des éprouvettes de mélanges bitumineux malaxés selon l'EN 12697-35 et compactés à l'aide d'un compacteur à impact selon l'EN 12697-30. Elle est limitée aux bétons bitumineux denses et aux « hot rolled asphalt ».

Bitumenske zmesi - Preskusne metode za vroče asfaltne zmesi - 34. del: Preskus po Marshallu

Ta evropski standard določa preskusno metodo za ugotavljanje stabilnosti, toka in vrednosti Marshallovega količnika preskušancev bitumenskih zmesi, pripravljenih v skladu s standardom EN 12697-35 in z uporabo metode udarnega zgoščevalnika pri preskusu iz standarda EN 12697-30. Omejen je na gosto penetrirani liti asfalt in vroče valjani asfalt.

General Information

Status
Withdrawn
Publication Date
08-May-2012
Withdrawal Date
25-Feb-2020
Current Stage
9960 - Withdrawal effective - Withdrawal
Due Date
09-May-2012
Completion Date
26-Feb-2020

Relations

Buy Standard

Standard
EN 12697-34:2012
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Asphalt - Prüfverfahren für Heißasphalt - Teil 34: Marshall-PrüfungMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 34 : Essai MarshallBituminous mixtures - Test methods for hot mix asphalt - Part 34: Marshall test93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12697-34:2012SIST EN 12697-34:2012en,fr,de01-september-2012SIST EN 12697-34:2012SLOVENSKI

STANDARDSIST EN 12697-34:2004+A1:20071DGRPHãþD
SIST EN 12697-34:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12697-34
May 2012 ICS 93.080.20 Supersedes EN 12697-34:2004+A1:2007English Version
Bituminous mixtures - Test methods for hot mix asphalt - Part 34: Marshall test

Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 34 : Essai Marshall

Asphalt - Prüfverfahren für Heißasphalt - Teil 34: Marshall-Prüfung This European Standard was approved by CEN on 30 March 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,

B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12697-34:2012: ESIST EN 12697-34:2012

EN 12697-34:2012 (E) 2 Contents Page Foreword ..............................................................................................................................................................31 Scope ......................................................................................................................................................72 Normative references ............................................................................................................................73 Terms and definitions ...........................................................................................................................74 Principle ..................................................................................................................................................85 Apparatus ...............................................................................................................................................86 Procedure ...............................................................................................................................................86.1 Specimen preparation ...........................................................................................................................86.2 Test procedure .......................................................................................................................................97 Expression of results ............................................................................................................................98 Test report ........................................................................................................................................... 109 Precision .............................................................................................................................................. 10Annex A (normative)

Marshall stability and flow values .............................................................................. 11Annex B (normative)

Testing head ................................................................................................................. 12Bibliography ..................................................................................................................................................... 13 SIST EN 12697-34:2012

EN 12697-34:2012 (E) 3 Foreword This document (EN 12697-34:2012) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the latest by May 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12697-34:2004+A1:2007. The significant changes with respect to the previous edition are: a) definition of stability revised; b) definition of total flow added; c) note added on need for graphical plotter; d) note added allowing alternative number of votes; e) staking of specimens not permitted; f) note added about rapid cooling of rolled asphalt specimens; g) requirements for measurement of flow revised; h) equation for calculating the corrected stability revised with units in cubic millimetres rather than millilitres; i) calculation of flow clarified; j) Annex A revised. Annexes A and B are normative. This document is one of a series of European Standards which specify various test methods for bituminous mixtures. It includes the following parts:

 EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content  EN 12697-2, Bituminous mixtures — Test method for hot mix asphalt — Part 2: Determination of particle size distribution  EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotary evaporator  EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery: Fractionating column  EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density SIST EN 12697-34:2012

EN 12697-34:2012 (E) 4  EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density of bituminous specimens  EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays  EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of void characteristics of bituminous specimens  EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactability  EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of the affinity between aggregate and bitumen  EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the water sensitivity of bituminous specimens  EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement  EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content  EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity  EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres  EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Particle loss of porous asphalt specimen  EN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage  EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen  EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or cylindrical specimens  EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate specimens  EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking  EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of the indirect tensile strength of bituminous specimens  EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue  EN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test  EN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness  EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling  EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading SIST EN 12697-34:2012

EN 12697-34:2012 (E) 5  EN 12697-29, Bituminous mixtures — Test methods for hot mix asphalt — Part 29: Determination of the dimensions of a bituminous specimen  EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor  EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor  EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of bituminous mixtures by vibratory compactor  EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared by roller compactor  EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test  EN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing  EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of the thickness of a bituminous pavement  EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for the adhesivity of binder on precoated chippings for HRA  EN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Common equipment and calibration  EN 12697-39, Bituminous mixtures — Test methods for hot mix asphalt — Part 39: Binder content by ignition  EN 12697-40, Bituminous mixtures — Test methods for hot mix asphalt — Part 40: In situ drainability  EN 12697-41, Bituminous mixtures — Test methods for hot mix asphalt — Part 41: Resistance to de-icing fluids  EN 12697-42, Bituminous mixtures — Test methods for hot mix asphalt — Part 42: Amount of coarse foreign matter in reclaimed asphalt  EN 12697-43, Bituminous mixtures — Test methods for hot mix asphalt — Part 43: Resistance to fuel  EN 12697-44, Bituminous mixtures — Test methods for hot mix asphalt — Part 44: Crack propagation by semi-circular bending test  EN 12697-45, Bituminous mixtures — Test methods for hot mix asphalt — Part 45: Saturation Ageing Tensile Stiffness (SATS) conditioning test  EN 12697-46, Bituminous mixtures — Test methods for hot mix asphalt — Part 46: Low temperature cracking and properties by uniaxial tension tests  EN 12697-47, Bituminous mixtures — Test methods for hot mix asphalt — Part 47: Determination of the ash content of natural asphalts  prEN 12697-48, Bituminous mixtures — Test methods for hot mix asphalt — Part 48: Interlayer bond strength1)

1) In preparation. SIST EN 12697-34:2012

EN 12697-34:2012 (E) 6  prEN 12697-49, Bituminous mixtures — Test methods for hot mix asphalt — Part 49: Skid resistance of

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.