EN 14399-6:2005

High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers

This part of this European Standard specifies, together with prEN 14399-1, hardened and tempered plain washers with chamfer intended for assembly with large series hexagon high-strength structural bolts and nuts with thread sizes from M12 to M36 inclusive.
NOTE   Attention is drawn to the importance of ensuring that the washers are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to ENV 1090-1 is made.

Hochfeste planmäßig vorspannbare Schraubenverbindungen für den Metallbau - Teil 6: Flache Scheiben mit Fase

Dieser Teil der europäischen Norm beschreibt, zusammen mit prEN 14399-1, vergütete flache Scheiben mit Fase, welche für die Verwendung mit hochfesten vorspannbaren Sechskantschrauben und -muttern mit großer Schlüsselweite für den Metallbau mit Gewindegrößen von M12 bis M36, vorgesehen sind.
ANMERKUNG   Damit zufriedenstellende Ergebnisse erreicht werden können, ist auf die korrekte Anwendung der Scheiben besondere Aufmerksamkeit zu richten. Für Empfehlungen zur korrekten Anwendung wird auf ENV 1090-1 hingewiesen.

Boulonnerie de construction métallique à haute résistance apte à la précontrainte - Partie 6 : Rondelles plates chanfreinées

La présente partie de cette Norme européenne, avec le prEN 14399-1, spécifie les exigences applicables aux rondelles plates chanfreinées, trempées et revenues, destinées à être assemblées avec des vis et écrous hexagonaux de construction à haute résistance des systèmes HR ou HV, à surplat de série large et de diamètre de filetage de M12 à M36 inclus.
NOTE   Il est important de s'assurer que les rondelles soient utilisées de façon correcte afin d'obtenir un résultat satisfaisant. Pour les recommandations relatives à la bonne utilisation, se référer à l'ENV 1090-1.

Visokotrdnostne strukturne vijačne zveze za prednapetje - 6. del: Ploščate posnete podložke

General Information

• Status: Withdrawn
• Publication Date: 15-Mar-2005
• Withdrawal Date: 17-Feb-2015
• ICS: 21.060.30 - Washers, locking elements
• Technical Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Drafting Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 18-Feb-2015
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Mandate: M/120 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on structural metallic products and ancillaries
• Ref Project: SIST EN 14399-6:2005 - High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers

Relations

• Replaced By: EN 14399-6:2015 - High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
• Effective Date: 25-Feb-2015
• Corrected By: EN 14399-6:2005/AC:2006 - High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 14399-6:2005
01-maj-2005
9LVRNRWUGQRVWQHVWUXNWXUQHYLMDþQH]YH]H]DSUHGQDSHWMHGHO3ORãþDWHSRVQHWH
SRGORåNH
High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered
washers
Hochfeste planmäßig vorspannbare Schraubenverbindungen für den Metallbau - Teil 6:
Flache Scheiben mit Fase
Boulonnerie de construction métallique a haute résistance apte a la précontrainte - Partie
6 : Rondelles plates chanfreinées
Ta slovenski standard je istoveten z: EN 14399-6:2005
ICS:
21.060.30 Podložke, varovalni elementi Washers, locking elements
SIST EN 14399-6:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 14399-6:2005

---------------------- Page: 2 ----------------------

SIST EN 14399-6:2005
EUROPEAN STANDARD
EN 14399-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2005
ICS 21.060.30
English version
High-strength structural bolting assemblies for preloading - Part
6: Plain chamfered washers
Boulonnerie de construction métallique à haute résistance Hochfeste planmäßig vorspannbare
apte à la précontrainte - Partie 6 : Rondelles plates Schraubenverbindungen für den Metallbau - Teil 6: Flache
chanfreinées Scheiben mit Fase
This European Standard was approved by CEN on 30 April 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14399-6:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 14399-6:2005
EN 14399-6:2005 (E)
Contents page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Dimensions.6
4 Specification and reference standards .7
5 Designation .7
6 Marking .7
Bibliography .8


2

---------------------- Page: 4 ----------------------

SIST EN 14399-6:2005
EN 14399-6:2005 (E)
Foreword
This document (EN 14399-6:2005) has been prepared by Technical Committee CEN /TC 185 "Threaded and
non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by September 2005, and conflicting national standards shall be withdrawn at the
latest by September 2005.
This document includes a Bibliography.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are b
...