prEN 13523-1
(Main)Coil coated metals - Test methods - Part 1: Film thickness
Coil coated metals - Test methods - Part 1: Film thickness
This document specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Five appropriate methods are given in this document:
a) magnetic induction;
b) eddy current;
c) micrometer;
d) optical;
e) ruggedized optical interference.
The methods are applicable only to products with smooth and flat substrates, but the coating itself can be textured. In that case, for methods a) and b), the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness, method d) can provide the minimum, maximum and average thickness, and e) will give the total thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness are only applicable on method a).
Bandbeschichtete Metalle - Prüfverfahren - Teil 1: Schichtdicke
Dieses Dokument legt die Verfahren zum Bestimmen der Trockenschichtdicke einer organischen Beschichtung auf einem metallischen Substrat (Bandbeschichtung) fest.
Fünf geeignete Verfahren werden in diesem Dokument angegeben:
a) Magnetoinduktion;
b) Wirbelstrom;
c) Messschraube;
d) optisch;
e) robuste optische Interferenz.
Die Verfahren sind nur auf Produkte mit glatten und ebenen Substraten anwendbar, die Beschichtung selbst kann aber strukturiert sein. In diesem Fall stellt bei den Verfahren a) und b) der Mittelwert einer Reihe von Messungen einen Durchschnittswert der Dicke der organischen Beschichtung dar, während Verfahren c) die größte Schichtdicke ergibt, mit Verfahren d) die kleinste, größte und durchschnittliche Schichtdicke ermittelt werden kann und Verfahren e) die Gesamtdicke ergibt.
Nicht zerstörende Verfahren zum Messen der Trockenschichtdicke für Endlosbahnen sind nur bei Verfahren a) anwendbar.
Tôles prélaquées - Méthodes d’essai - Partie 1 : Épaisseur du feuil
Le présent document spécifie les méthodes de détermination de l’épaisseur de feuil sec d’un revêtement organique sur un subjectile métallique (prélaquage en bandes continues).
Cinq méthodes adaptées sont décrites dans le présent document :
a) induction magnétique ;
b) courants de Foucault ;
c) micromètre ;
d) optique ;
e) interférences optiques renforcées (ROI).
Ces méthodes s’appliquent seulement aux produits qui comprennent des subjectiles lisses et plats, le revêtement lui même pouvant être texturé. Dans ce cas, pour les méthodes a) et b), la moyenne d’une série de lectures représentera une moyenne de l’épaisseur du revêtement organique, tandis que la méthode c) donnera l’épaisseur maximale, que la méthode d) peut fournir les épaisseurs minimales, maximales et moyennes, et que la technique e) fournira l’épaisseur totale.
Les méthodes non destructives sur toiles continues visant à déterminer l’épaisseur de feuil sec s’appliquent uniquement à la méthode a).
Prevlečene kovine, ki se navijajo - Preskusne metode - 1. del: Debelina premaza
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 13523-1:2023
01-september-2023
Prevlečene kovine, ki se navijajo - Preskusne metode - 1. del: Debelina premaza
Coil coated metals - Test methods - Part 1: Film thickness
Bandbeschichtete Metalle - Prüfverfahren - Teil 1: Schichtdicke
Tôles prélaquées - Méthodes d'essai - Partie 1 : Épaisseur du revêtement
Ta slovenski standard je istoveten z: prEN 13523-1
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13523-1:2023
---------------------- Page: 2 ----------------------
oSIST prEN 13523-1:2023
DRAFT
EUROPEAN STANDARD
prEN 13523-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2023
ICS 25.220.60; 17.040.20 Will supersede EN 13523-1:2017
English Version
Coil coated metals - Test methods - Part 1: Film thickness
Tôles prélaquées - Méthodes d'essai - Partie 1 : Bandbeschichtete Metalle - Prüfverfahren - Teil 1:
Épaisseur du revêtement Schichtdicke
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-1:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13523-1:2023
prEN 13523-1:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
4.1 Method A: Measurement on magnetic substrate – magnetic induction . 6
4.2 Method B: Measurement on a non-magnetic substrate – eddy current . 6
4.3 Method C: Measurement on all substrates – micrometer method . 6
4.4 Method D: Measurement on all substrates – optical method . 6
4.5 Method E: Measurement on all substrates – ruggedized optical interference (ROI) . 6
5 Apparatus and materials . 6
6 Sampling . 6
7 Test panels . 7
8 Procedure .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.