Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized

This European Standard specifies requirements for flat products for pressure equipment made of weldable fine
grain steels as specified in Table 1.
NOTE 1 Fine grain steels are understood as steels with a ferritic grain size of 6 or finer when tested in accordance with
EN ISO 643.
The requirements and definitions of EN 10028-1 also apply.
NOTE 2 Once this European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC, presumption of
conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this
European Standard (Part 1 and this Part 3 of the series) and does not presume adequacy of the material to a specific item of
equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements
of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied, needs to be done.

Flacherzeugnisse aus Druckbehälterstählen - Teil 3: Schweißgeeignete Feinkornbaustähle, normalgeglüht

In dieser Europäischen Norm sind die Anforderungen an Flacherzeugnisse für Druckbehälter aus den
schweißgeeigneten Feinkornbaustählen nach Tabelle 1 festgelegt.
ANMERKUNG 1 Unter Feinkornbaustählen werden Stähle verstanden, die bei Prüfung nach EN ISO 643 eine
Ferritkorngröße von 6 oder feiner aufweisen.
Zusätzlich gelten die Anforderungen und Begriffe in EN 10028-1:2007+A1:2009.
ANMERKUNG 2 Nach Veröffentlichung dieser Europäischen Norm im EU-Amtsblatt (OJEU) unter der Richtlinie
97/23/EC ist die Annahme ihrer Konformität mit den grundlegenden Anforderungen (ESR) der Richtlinie 97/23/EC auf
die technischen Daten von Werkstoffen in dieser Europäischen Norm (Teil 1 und dieser Teil 3 der Normenreihe)
beschränkt, und es darf nicht angenommen werden, dass damit die Eignung des Werkstoffs für ein bestimmtes
Ausrüstungsteil festgestellt ist. Folglich müssen die in dieser Werkstoffnorm angegebenen technischen Parameter im
Hinblick auf die konstruktiven Anforderungen dieses bestimmten Ausrüstungsteils ermittelt werden, um damit zu
verifizieren, dass den ESR der Richtlinie 97/23/EC entsprochen wird.
ESR der Richtlinie 97/23/EG entsprochen wird.

Produits plats en aciers pour appareils à pression - Partie 3: Aciers soudables à grains fins, normalisés

La présente Norme européenne spécifie les prescriptions relatives aux produits plats pour appareils à pression en
aciers à grains fins aptes au soudage, telles que spécifiées dans le Tableau 1.
NOTE 1 Par «aciers à grains fins», on entend les aciers ayant une grosseur de grain ferritique 6 ou plus fin, déterminée
conformément à l'EN ISO 643.
Les prescriptions et définitions de l’EN 10028-1 s’appliquent également.
NOTE 2 Après publication de la présente Norme européenne dans le Journal Officiel de l'UE (OJEU) sous la Directive
97/23/EC, la présomption de conformité aux Exigences Essentielles de Sécurité (ESRs) de la Directive 97/23/EC se limite aux
données techniques des matériaux de la présente Norme européenne (Partie 1 et la présente Partie 3 de la série) et ne
suppose pas l'adéquation du matériau à un élément ou à un équipement spécifique. En conséquence, l'évaluation des données
techniques énoncées dans la présente norme de matériau en fonction des exigences de conception de cet élément spécifique
d'équipement pour vérifier que les ESR de la Directive 97/23/EC sont respectées, doit être effectuée.

Ploščati jekleni izdelki za tlačne posode - 3. del: Variva drobnozrnata jekla, normalizirana

General Information

Status
Withdrawn
Publication Date
16-Jun-2009
Withdrawal Date
25-Jul-2017
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
26-Jul-2017

Relations

Buy Standard

Standard
EN 10028-3:2009
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.QRUPDOL]LUDQDFlacherzeugnisse aus Druckbehälterstählen - Teil 3: Schweißgeeignete Feinkornbaustähle, normalgeglühtProduits plats en aciers pour appareils à pression - Partie 3: Aciers soudables à grains fins, normalisésFlat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized77.140.50SROL]GHONLFlat steel products and semi-products77.140.30Jekla za uporabo pod tlakomSteels for pressure purposesICS:Ta slovenski standard je istoveten z:EN 10028-3:2009SIST EN 10028-3:2009en,fr,de01-september-2009SIST EN 10028-3:2009SLOVENSKI
STANDARDSIST EN 10028-3:20031DGRPHãþD



SIST EN 10028-3:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10028-3June 2009ICS 77.140.30; 77.140.50Supersedes EN 10028-3:2003
English VersionFlat products made of steels for pressure purposes - Part 3:Weldable fine grain steels, normalizedProduits plats en aciers pour appareils à pression - Partie3: Aciers soudables à grains fins, normalisésFlacherzeugnisse aus Druckbehälterstählen - Teil 3:Schweißgeeignete Feinkornbaustähle, normalgeglühtThis European Standard was approved by CEN on 14 May 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10028-3:2009: ESIST EN 10028-3:2009



EN 10028-3:2009 (E) 2 Contents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Dimensions and tolerances on dimensions . 4 5 Calculation of mass . 4 6 Classification and designation . 4 6.1 Classification . 4 6.2 Designation . 5 7 Information to be supplied by the purchaser . 5 7.1 Mandatory information . 5 7.2 Options . 5 7.3 Example for ordering . 5 8 Requirements . 6 8.1 Steelmaking process . 6 8.2 Delivery condition .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.