EN ISO 377:2013
(Main)Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2013, Corrected version 2015-06-01)
Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2013, Corrected version 2015-06-01)
ISO 377:2013 specifies requirements for the identification, location and preparation of samples and test pieces intended for mechanical tests on steel sections, bars, rod, flat products and tubular products as defined in ISO 6929. If agreed in the order, ISO 377:2013 can also apply to other metallic products. These samples and test pieces are for use in tests that are carried out in conformity with the methods specified in the product or material standard or, in the absence of this, in the standard for the test method.
Where the requirements of the order or product standard differ from those given in ISO 377:2013, then the requirements of the order or product standard apply.
Stahl und Stahlerzeugnisse - Lage und Vorbereitung von Probenabschnitten und Proben für mechanische Prüfungen (ISO 377:2013, korrigierte Fassung 2015-06-01)
Diese Internationale Norm legt Anforderungen an die Kennzeichnung, Lage und Vorbereitung von Probenabschnitten und Proben für mechanische Prüfungen an den in ISO 6929 definierten Profilen, Stäben, Walzdraht, Flacherzeugnissen und rohrförmigen Erzeugnissen aus Stahl fest. Falls bei der Bestellung vereinbart, kann diese Internationale Norm auch für andere metallische Erzeugnisse gelten. Sie gilt nicht für zerstörungsfreie Prüfungen.
Die Probenabschnitte und Proben sind für Prüfungen bestimmt, die nach den in der Erzeugnis- oder Werkstoffnorm festgelegten Verfahren oder, falls in diesen nichts angegeben ist, nach dem in der Prüfnorm angegebenen Verfahren durchgeführt werden.
Wenn die Anforderungen in der Bestellung oder der Erzeugnisnorm von den Anforderungen nach dieser Internationalen Norm abweichen, so gelten die Anforderungen entsprechend der Bestellung oder der Erzeugnisnorm.
Acier et produits en acier - Position et préparation des échantillons et éprouvettes pour essais mécaniques (ISO 377:2013, Version corrigée 2015-06-01)
L'ISO 377:2013 définit les exigences relatives à l'identification, à la position et à la préparation des échantillons et éprouvettes destinés aux essais mécaniques des profilés, barres, fils machine, et produits plats et tubulaires en acier, tels que définis dans l'ISO 6929. Par accord à la commande, l'ISO 377:2013 peut également s'appliquer à d'autres produits métalliques. Elle n'est pas applicable aux essais non destructifs. Ces échantillons et éprouvettes sont à utiliser dans les essais effectués conformément aux méthodes spécifiées dans la norme de produit ou, en absence de celle-ci, dans la norme d'essai.
Lorsque les exigences de la commande ou de la norme de produit diffèrent de celles données dans l'ISO 377:2013, les exigences définies à la commande ou spécifiées dans la norme de produit s'appliquent.
Jeklo in jekleni izdelki - Mesto jemanja in priprava vzorcev ter preskušanci za mehansko preskušanje (ISO 377:2013)
Ta mednarodni standard določa zahteve za prepoznavanje, lokacijo in pripravo vzorcev in preskusnih delov za mehanske preskuse na jeklenih delih, palicah, drogovih, ploščatih izdelkih in cevastih izdelkih, kot določa standard ISO 6929. Če je to sprejeto v sklepu, se lahko ta standard uporablja tudi za druge kovinske izdelke. Ti vzorci in preskusni deli se uporabljajo v preskusih, ki se opravljajo skladno z metodami, določenimi v standardu izdelka ali materiala oziroma, če ta ne obstaja, v preskusnem standardu. Kadar se zahteve sklepa ali standarda izdelka razlikujejo od zahtev iz tega mednarodnega standarda, se uporabljajo zahteve sklepa ali standarda izdelka.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2013
1DGRPHãþD
SIST EN ISO 377:1998
Jeklo in jekleni izdelki - Mesto jemanja in priprava vzorcev ter preskušanci za
mehansko preskušanje (ISO 377:2013)
Steel and steel products - Location and preparation of samples and test pieces for
mechanical testing (ISO 377:2013)
Stahl und Stahlerzeugnisse - Lage und Vorbereitung von Probenabschnitten und Proben
für mechanische Prüfungen (ISO 377:2013)
Acier et produits en acier - Position et préparation des échantillons et éprouvettes pour
essais mécaniques (ISO 377:2013)
Ta slovenski standard je istoveten z: EN ISO 377:2013
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
77.140.01 Železni in jekleni izdelki na Iron and steel products in
splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 377
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2013
ICS 77.040.10 Supersedes EN ISO 377:1997
English Version
Steel and steel products - Location and preparation of samples
and test pieces for mechanical testing (ISO 377:2013)
Acier et produits en acier - Position et préparation des Stahl und Stahlerzeugnisse - Lage und Vorbereitung von
échantillons et éprouvettes pour essais mécaniques (ISO Probenabschnitten und Proben für mechanische Prüfungen
377:2013) (ISO 377:2013)
This European Standard was approved by CEN on 29 June 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 377:2013: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 377:2013) has been prepared by Technical Committee ISO/TC 17 “Steel” in
collaboration with Technical Committee ECISS/TC 100 “General issues” the secretariat of which is held by
BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2014, and conflicting national standards shall be withdrawn at
the latest by January 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 377:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 377:2013 has been approved by CEN as EN ISO 377:2013 without any modification.
INTERNATIONAL ISO
STANDARD 377
Third edition
2013-07-01
Steel and steel products — Location
and preparation of samples and test
pieces for mechanical testing
Acier et produits en acier — Position et préparation des échantillons
et éprouvettes pour essais mécaniques
Reference number
ISO 377:2013(E)
©
ISO 2013
ISO 377:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
ISO 377:2013(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
4.1 Representative testing . 2
4.2 Identification of sample products, samples, rough specimens and test pieces . 2
5 Preparation of samples and selection of test pieces . 3
5.1 Selection and dimensions of samples and location of test pieces. 3
5.2 Direction of axis of test pieces . 3
5.3 Condition and separation of samples . 4
6 Preparation of test pieces . 4
6.1 Cutting and machining . 4
6.2 Reference heat treatment . 5
Annex A (normative) Location of samples and test pieces . 6
ISO 377:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 17, Steel, Subcommittee SC 20, General technical
delivery conditions, sampling and mechanical testing methods.
This third edition cancels and replaces the second edition (ISO 377:1997), which has been technically
revised and includes ISO 377:1997/Cor.1:1997.
iv © ISO 2013 – All rights reserved
INTERNATIONAL STANDARD ISO 377:2013(E)
Steel and steel products — Location and preparation of
samples and test pieces for mechanical testing
1 Scope
This International Standard specifies requirements for the identification, location and preparation of
samples and test pieces intended for mechanical tests on steel sections, bars, rod, flat products and
tubular products as defined in ISO 6929. If agreed in the order, this International Standard can also
apply to other metallic products. These samples and test pieces are for use in tests that are carried out
in conformity with the methods specified in the product or material standard or, in the absence of this,
in the standard for the test method.
Where the requirements of the order or product standard differ from those given in this International
Standard, then the requirements of the order or product standard apply.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the editions cited applies. For undated references, the latest edition of the referenced
document, (including any amendments) apply.
ISO 3785, Metallic materials — Designation of test specimen axes in relation to product texture
ISO 6929, Steel products — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6929 and the following apply.
3.1
test unit
number of pieces or the tonnage of products to accept or reject together, on the basis of the verification
tests carried out on sample products in accordance with the requirements of the product standard or order
Note 1 to entry: See Figure 1.
3.2
sample product
item (e.g. bar, sheet, coil) selected for inspection or testing
Note 1 to entry: See Figure 1.
3.3
sample
sufficient quantity of material taken from the sample product for the purpose of producing one or
more test pieces
Note 1 to entry: See Figure 1.
Note 2 to entry: In certain cases, the sample can be the sample product.
ISO 377:2013(E)
3.4
rough specimen
part of a sample having undergone mechanical treatment, for the purpose of producing a test piece
Note 1 to entry: See Figure 1.
3.5
test piece
part of a sample or rough specimen, with specified dimensions, machined or unmachined, brought to a
required condition for submission to a given verification test
Note 1 to entry: See Figure 1.
Note 2 to entry: In certain cases, the test piece can be the sample or the rough specimen.
3.6
reference condition
condition of a sample, rough specimen or test piece having undergone a heat treatment to represent the
intended final condition of the product
Note 1 to entry: In such cases, the sample, rough specimen or test piece is called the reference sample, reference
rough specimen or reference test piece.
4 General requirements
4.1 Representative testing
Sample, rough specimens and test pieces selected in accordance with Annex A shall be considered to be
representative of the product.
NOTE As a result of their production sequence, e.g. melting, casting hot or cold forming or both, heat
treatment etc., steel products are not homogeneous. The mechanical properties of samples taken from other
locations can be different.
4.2 Identification of sample products, samples, rough specimens and test pieces
Sample products, samples, rough specimens and test pieces shall be marked to ensure traceability to
the original product and their location and orientation in that product. For this purpose, if, during the
preparation of any one or more of the samples, rough specimens or test pieces, removal of the marks
cannot be avoided, transfer of these marks shall be carried out before the existing marks are removed
or in the case of automatic preparation equipment before the test p
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.