EN 14125:2004
(Main)Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
This document specifies requirements for underground pipework systems used to transfer liquid fuels and their vapours at petrol filling stations. Minimum performance requirements covering fitness for purpose, safety and environmental protection are given.
This document applies to pipework made from thermoplastics, which may include some degree of reinforcement, and to flexible metal pipework. It does not apply to fibre reinforced thermosets, commonly referred to as glass fibre reinforced plastic (GRP), nor to rigid metals.
This document applies to:
- delivery pipes from tanks to dispensers, including positive pressure, vacuum suction and siphon modes;
- fill pipes from road tankers to tanks;
- vapour recovery and vent pipework;
- pipework for secondary containment;
- connectors.
It does not apply to pipework for use with liquefied petroleum gas.
Thermoplastische und flexible metallene Rohrleitungen für erdverlegte Installationen für Tankstelle
Tuyauteries enterrées thermoplastiques et tuyauteries métalliques flexibles pour stations-service
Le présent document spécifie les exigences relatives aux installations de tuyauteries enterrées utilisées pour le transfert des carburants liquides et de leurs vapeurs dans les stations-service. Il donne les exigences relatives aux performances minimales couvrant l'aptitude à l'emploi, la sécurité et la protection de l'environnement.
Le présent document s'applique aux tuyauteries en matériaux thermoplastiques pouvant comporter certains renforts, ainsi qu'aux tuyauteries métalliques flexibles. Elle ne s'applique ni aux matériaux thermodurcissables renforcés par des fibres, généralement désignés par plastique renforcé à la fibre de verre (GRP), ni aux métaux rigides.
Le présent document s'applique :
- aux conduites d'alimentation des installations de distribution à partir des réservoirs, y compris les modes de pression positive, l'aspiration et de siphonnage à dépression ;
- aux tubes de remplissage des réservoirs à partir des camions-citernes ;
- à la récupération des vapeurs et aux tuyauteries d'aération (évent) ;
- aux tuyauteries destinées au confinement secondaire ;
- aux raccords.
Elle ne s'applique pas aux tuyauteries réservées au gaz de pétrole liquéfié (GPL).
Cevovodi iz kovinskih gibljivih cevi in cevi iz plastomerov za podzemne napeljave za bencinske servise
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevovodi iz kovinskih gibljivih cevi in cevi iz plastomerov za podzemne napeljave za bencinske serviseThermoplastische und flexible metallene Rohrleitungen für erdverlegte Installationen für TankstelleTuyauteries enterrées thermoplastiques et tuyauteries métalliques flexibles pour stations-serviceThermoplastic and flexible metal pipework for underground installation at petrol filling stations83.140.30Cevi, fitingi in ventili iz polimernih materialovPlastics pipes, fittings and valves75.200Petroleum products and natural gas handling equipment23.040.10Železne in jeklene ceviIron and steel pipesICS:Ta slovenski standard je istoveten z:EN 14125:2004SIST EN 14125:2005en,fr,de01-marec-2005SIST EN 14125:2005SLOVENSKI
STANDARD
SIST EN 14125:2005
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14125December 2004ICS 75.200English versionThermoplastic and flexible metal pipework for undergroundinstallation at petrol filling stationsTuyauteries enterrées thermoplastiques et en métauxflexibles pour stations-serviceThermoplastische und flexible metallene Rohrleitungen fürerdverlegte Installationen für TankstelleThis European Standard was approved by CEN on 15 November 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14125:2004: ESIST EN 14125:2005
EN 14125:2004 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.6 4 Classes and dimensions.7 5 Physical properties.8 6 Production control.13 7 Testing.13 8 Markings on pipe and connectors.20 9 Manuals.21 10 Records.22 Annex A (informative)
System of evaluation of conformity.23 Annex B (informative)
A–deviations.27 Bibliography.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.