EN 10210-1:2006
(Main)Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
This part of this European Standard specifies technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product.
Requirements for tolerances, dimensions and sectional properties are contained in EN 10210-2.
NOTE A range of material grades is specified in this standard and the user should select the grade appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are compatible with those in EN 10025-2 and EN 10025-3.
Warmgefertigte Hohlprofile für den Stahlbau aus unlegierten Baustählen und aus Feinkornbaustählen - Teil 1: Technische Lieferbedingungen
Dieser Teil dieser Europäischen Norm legt die technischen Lieferbedingungen für warmgefertigte Hohlprofile
mit kreisförmigem, quadratischem, rechteckigem oder elliptischem Querschnitt fest und gilt für warmgefertigte
Hohlprofile mit oder ohne nachfolgende Wärmebehandlung sowie für kaltgefertigte Hohlprofile, die
anschließend wärmebehandelt wurden, um eine gleichwertige metallurgische Beschaffenheit wie bei den
warmgefertigten Erzeugnissen zu erzielen.
Anforderungen an Grenzabmaße, Maße und statische Werte sind in EN 10210-2 enthalten.
ANMERKUNG In dieser Norm ist eine Reihe von Stahlsorten festgelegt, und der Anwender sollte die der vorgesehenen
Verwendung und den Betriebsbedingungen angemessene Sorte auswählen. Die Stahlsorten und mechanischen
Eigenschaften entsprechen weitgehend den Festlegungen in EN 10025-2 und EN 10025-3.
Profils creux de construction finis à chaud en aciers non alliés et à grains fins - Partie 1 : Conditions techniques de livraison
La présente partie de cette Norme européenne spécifie les conditions techniques de livraison des profils creux finis à chaud, de forme circulaire, carrée, rectangulaire ou elliptique et s'applique aux profils creux formés à chaud avec ou sans traitement thermique ou formés à froid avec traitement thermique ultérieur afin d'obtenir un état métallurgique équivalent à celui des produits formés à chaud.
Les prescriptions relatives aux tolérances, dimensions et caractéristiques de profil figurent dans l’EN 10210-2.
NOTE Dans cette norme, est spécifiée une gamme de nuances de matériau et il convient que l'utilisateur choisisse la nuance appropriée à l'utilisation prévue et aux conditions de service. Les nuances et les caractéristiques mécaniques des profils creux finis sont compatibles avec celles figurant dans l’EN 10025-2 et l’EN 10025-3.
Vroče izdelani votli profili iz nelegiranih in drobnozrnatih konstrukcijskih jekel - 1. del: Tehnični dobavni pogoji
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgefertigte Hohlprofile für den Stahlbau aus unlegierten Baustählen und aus Feinkornbaustählen - Teil 1: Technische LieferbedingungenProfils creux de construction finis a chaud en aciers non alliés et a grains fins - Partie 1 : Conditions techniques de livraisonHot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions77.140.70Jekleni profiliSteel profiles77.140.45Nelegirana jeklaNon-alloyed steelsICS:Ta slovenski standard je istoveten z:EN 10210-1:2006SIST EN 10210-1:2006en01-julij-2006SIST EN 10210-1:2006SLOVENSKI
STANDARDSIST EN 10210-1:19971DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10210-1April 2006ICS 77.140.75Supersedes EN 10210-1:1994
English VersionHot finished structural hollow sections of non-alloy and fine grainsteels - Part 1: Technical delivery conditionsProfils creux pour la construction finis à chaud en aciersnon alliés et à grains fins - Partie 1 : Conditions techniquesde livraisonWarmgefertigte Hohlprofile für den Stahlbau ausunlegierten Baustählen und aus Feinkornbaustählen - Teil1: Technische LieferbedingungenThis European Standard was approved by CEN on 16 March 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10210-1:2006: ESIST EN 10210-1:2006
Structural hollow sections of non-alloy quality steels — Chemical composition and mechanical properties.21 Annex B (normative)
Structural hollow sections of fine grain steels — Chemical composition and mechanical properties.23 Annex C (normative)
Location of samples and test pieces.26 Annex D (normative)
Evaluation of conformity.28 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Directive.33 Bibliography.38 SIST EN 10210-1:2006
1 Scope This part of this European Standard specifies technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product.
Requirements for tolerances, dimensions and sectional properties are contained in EN 10210-2. NOTE A range of material grades is specified in this standard and the user should select the grade appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are compatible with those in EN 10025-2 and EN 10025-3. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 287-1, Qualification test of welders - Fusion welding - Part 1: Steels EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test at ambient temperature EN 10020:2000, Definition and classification of grades of steel EN 10021:1993, General technical delivery requirements for steel and iron products EN 10027-1, Designation systems for steels
— Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10045-1, Metallic materials — Charpy impact test — Part 1: Test method
EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10168, Steel products - Inspection documents - List of information and description EN 10204, Metallic products — Types of inspection documents EN 10210-2:2006, Hot finished structural hollow sections of non-alloy and fine grain steels - Part 2: Tolerances, dimensions and sectional properties EN 10246-3, Non-destructive testing of steel tubes — Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections EN 10246-5, Non-destructive testing of steel tubes — Part 5: Automatic full peripheral magnetic transducer/flux leakage testing of seamless and welded (except submerged arc welded) ferromagnetic steel tubes for the detection of longitudinal imperfections EN 10246-8, Non-destructive testing of steel tubes — Part 8: Automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections SIST EN 10210-1:2006
EN 10246-10, Non-destructive testing of steel tubes — Part 10: Radiographic testing of the weld seam of automatic fusion arc welded steel tubes for the detection of imperfections EN 10256, Non-destructive testing of steel tubes - Qualification and competence of level 1 and 2 non-destructive testing personnel CR 10261, ECISS Information Circular 11 — Iron and steel — Review of available methods of chemical analysis EN 10266:2003, Steel tubes, fittings and structural hollow sections - Symbols and definitions of terms for use in product standards EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 643, Steels - Micrographic determination of the apparent grain size (ISO 643:2003) EN ISO 2566-1, Steel — Conversion of elongation values — Part 1: Carbon and low alloy steels (ISO 2566-1:1984) EN ISO 9001:2000, Quality management systems — Requirements (ISO 9001:2000) EN ISO 14284, Steel and iron - Sampling and preparation of samples for the determination of chemical com
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.