EN 13483:2005
(Main)Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
This European Standard specifies the requirements for hoses and hose assemblies for measured fuel dispensing systems with an internal vapour recovery tubing or hose.
The assemblies are intended for use at ambient temperatures between -30 °C and +65 °C and at a working pressure up to and including 3,5 bar ).
NOTE 1 Other temperature limits may be agreed between the hose manufacturer and the purchaser.
NOTE 2 For general operational conditions see annex A (informative).
Gummi- und Kunststoffschläuche und -schlauchleitungen mit innenliegender Gasrückführung für Zapfsäulen an Tankstellen - Anforderungen
Dieses Dokument legt Anforderungen an Schlauchleitungen mit Gasruckfuhrung fur Zapfsaulen an Tank-
stellen fest.
Die Schlauchleitungen mit Gasruckfuhrung fur Zapfsaulen an Tankstellen mussen den zu erwartenden
mechanischen, thermischen und chemischen Beanspruchungen widerstehen konnen und gegen die bei
diesen Anwendungen auftretenden brennbaren Flussigkeiten sowie deren Gase und Gas-Luft-Gemische
bestandig sein. Die Schlauchleitungen mussen so gebaut sein, dass das Arbeiten wahrend des normalen
Betriebs keine gefahrlichen elektrostatischen Aufladungen erzeugen oder die Leistung der Gasruckfuhrung
verringern kann.
Die Leitungen sind fur den Einsatz bei Umgebungstemperaturen vorgesehen, die fur die
Normaltemperaturklasse zwischen . 30 ¡ÆC und + 55 ¡ÆC und fur die Tieftemperaturklasse zwischen . 40 ¡ÆC
und + 55 ¡ÆC bei einem Betriebsdruck ¡Â 16 bar 1) liegen.
Die Schlauche durfen aus Gummi oder einem thermoplastischen Elastomer (TPE) hergestellt werden, und in
dem vorliegenden Dokument werden Anforderungen an drei Schlauchtypen festgelegt und zwar fur zwei
Kategorien und zwei Klassen von Schlauchleitungen fur Zapfsaulen einschlie©¬lich von Schlauchen mit
innenliegender Gasruckfuhrung, ohne oder mit Einlage, die fur mit sauerstoffhaltigen Verbindungen
angereicherte Kraftstoffe vorgesehen sind (bis zu einem maximalen Anteil von 15 % sauerstoffhaltigen
Verbindungen).
Tuyaux et flexibles en caoutchouc et en plastique à récupération interne de vapeur pour un système de distribution mesurée de carburants - Spécifications
La présente norme européenne spécifie les exigences relatives aux tuyaux et flexibles des systèmes de distribution mesurée de carburant comportant un tube ou un tuyau de récupération interne de vapeur.
Les flexibles sont destinés à être utilisés à des températures ambiantes comprises entre -30 °C et +65 °C et à une pression en service inférieure ou égale à 3,5 bar ) .
NOTE 1 Le fabricant des tuyaux et l'acheteur peuvent convenir d'autres limites de température.
NOTE 2 Pour les conditions générales de fonctionnement, voir l'annexe A (informative).
Gumene in polimerne cevi ter cevni priključki z notranjim sistemom za rekuperiranje hlapov za sisteme za merjeno točenje goriva na bencinskih črpalkah - Specifikacija
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gummi- und Kunststoffschläuche und -schlauchleitungen mit innenliegender Gasrückführung für Zapfsäulen an Tankstellen - AnforderungenTuyaux et flexibles en caoutchouc et en plastique a récupération interne de vapeur pour un systeme de distribution mesurée de carburants - SpécificationsRubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification83.140.40Gumene ceviHoses75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 13483:2005SIST EN 13483:2005en01-julij-2005SIST EN 13483:2005SLOVENSKI
STANDARD
SIST EN 13483:2005
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13483May 2005ICS 23.040.70; 75.200English versionRubber and plastic hoses and hose assemblies with internalvapour recovery for measured fuel dispensing systems -SpecificationTuyaux et flexibles à récupération interne de vapeur pourun système de livraison mesurée carburant - SpécificationGummi- und Kunststoffschläuche und -schlauchleitungenmit innenliegender Gasrückführung für Zapfsäulen anTankstellen - AnforderungenThis European Standard was approved by CEN on 21 March 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13483:2005: ESIST EN 13483:2005
EN 13483:2005 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.5 4 Classification.5 5 Materials and construction.5 6 Pressure requirements.6 7 Dimensions and tolerances.6 8 Physical properties.7 9 End fittings.10 10 Type tests.12 11 Frequency of testing.12 12 Marking.12 Annex A (normative)
Test method for determination of low temperature class resistance at –30 ºC and –40 °C.13 Annex B (normative)
Test method for pressure requirements of vapour recovery hoses and tubes.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.