EN ISO 6721-1:2002
(Main)Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2001)
Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2001)
Revision instead of amendment in order to follow ISO + UAP instead of EN/ENQ+FV-VA/ISO (CC/000817)
Kunststoffe - Bestimmung dynamisch-mechanischer Eigenschaften - Teil 1: Allgemeine Grundlagen (ISO 6721-1:2001)
Diese Internationale Norm legt Verfahren zur Bestimmung der dynamisch-mechanischen Eigenschaften von steifen Kunststoffen im Bereich des linear-viskoelastischen Verhaltens fest. Dieser Teil von ISO 6721 ist ein Einführungsteil, der die Definitionen und alle Gesichtspunkte enthält, die für die einzelnen, in den folgenden Teilen beschriebenen Prüfverfahren gültig sind.
Unterschiedliche Deformationsarten können Ergebnisse hervorrufen, die nicht direkt vergleichbar sind. Zum Beispiel ergeben Zugschwingungen Spannungen, die über die gesamte Dicke des Probekörpers gleichförmig sind, während Biege-Messungen bevorzugt durch die Eigenschaften von Oberflächen-Gebieten beeinflusst sind.
Eigenschaftswerte aus Biegeprüfungen sind nur mit solchen aus Zugprüfungen vergleichbar in Spannungs-bereichen, in denen die Spannungs-Dehnungs-Beziehung linear ist, und für Probekörper mit homogener Struktur.
Plastiques - Détermination des propriétés mécaniques dynamiques - Partie 1: Principes généraux (ISO 6721-1:2001)
Polimerni materiali - Določanje dinamičnih mehanskih lastnosti - 1. del: Splošna načela (ISO 6721-1:2001)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2003
1DGRPHãþD
SIST EN ISO 6721-1:1999
SIST EN ISO 6721-1:1999
3ROLPHUQLPDWHULDOL'RORþDQMHGLQDPLþQLKPHKDQVNLKODVWQRVWLGHO 6SORãQD
QDþHOD ,62
Plastics - Determination of dynamic mechanical properties - Part 1: General principles
(ISO 6721-1:2001)
Kunststoffe - Bestimmung dynamisch-mechanischer Eigenschaften - Teil 1: Allgemeine
Grundlagen (ISO 6721-1:2001)
Plastiques - Détermination des propriétés mécaniques dynamiques - Partie 1: Principes
généraux (ISO 6721-1:2001)
Ta slovenski standard je istoveten z: EN ISO 6721-1:2002
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 6721-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2002
ICS 83.080.01 Supersedes EN ISO 6721-1:1996
English version
Plastics - Determination of dynamic mechanical properties - Part
1: General principles (ISO 6721-1:2001)
Plastiques - Détermination des propriétés mécaniques Kunststoffe - Bestimmung dynamisch-mechanischer
dynamiques - Partie 1: Principes généraux (ISO 6721- Eigenschaften - Teil 1: Allgemeine Grundlagen (ISO 6721-
1:2001) 1:2001)
This European Standard was approved by CEN on 19 August 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6721-1:2002 E
worldwide for CEN national Members.
Foreword
The text of ISO 6721-1:2001 has been prepared by Technical Committee ISO/TC 61 "Plastics"
of the International Organization for Standardization (ISO) and has been taken over as
held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2003, and conflicting national
standards shall be withdrawn at the latest by March 2003.
This document supersedes EN ISO 6721-1:1996.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 6721-1:2001 has been approved by CEN as a
European Standard without any modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated by (mod.),
the relevant EN/HD applies.
Publication Year Title EN/HD Year
ISO 291 1997 Plastics - Standard atmospheres for EN ISO 291 1997
conditioning and testing
ISO 294-1 1996 Plastics - Injection moulding of test EN ISO 294-1 1998
specimens of thermoplastic materials -
Part 1: General principles, and moulding
of multipurpose and bar test specimens
ISO 294-2 1996 Plastics - Injection moulding of test EN ISO 294-2 1998
specimens of thermoplastic materials -
Part 2: Small tensile bars
ISO 294-3 1996 Plastics - Injection moulding of test EN ISO 294-3 1998
specimens of thermoplastic materials -
Part 3: Small plates
ISO 294-4 1996 Plastics - Injection moulding of test EN ISO 294-4 1998
specimens of thermoplastic materials -
Part 4: Determination of moulding
shrinkage
ISO 295 1991 Plastics - Compression moulding of test EN ISO 295 1998
specimens of thermosetting materials
ISO 2818 1994 Plastics - Preparation of test specimens EN ISO 2818 1996
by machining
ISO 6721-2 1994 Plastics - Determination of dynamic EN ISO 6721-2 1996
mechanical properties - Part 2: Torsion-
pendulum method
ISO 6721-3 1994 Plastics - Determination of dynamic EN ISO 6721-3 1996
mechanical properties - Part 3: Flexural
vibration - Resonance-curve method
INTERNATIONAL ISO
STANDARD 6721-1
Second edition
2001-05-15
Plastics — Determination of dynamic
mechanical properties —
Part 1:
General principles
Plastiques — Détermination des propriétés mécaniques dynamiques —
Partie 1: Principes généraux
Reference number
ISO 6721-1:2001(E)
ISO 6721-1:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec-
tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's mem-
ber body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2001 – All rights reserved
ISO 6721-1:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 6721 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 6721-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2,
Mechanical properties.
This second edition cancels and replaces the first edition (ISO 6721-1:1994), of which it constitutes a minor revision
(two further references have been added to the bibliography).
ISO 6721 consists of the following parts, under the general title Plastics — Determination of dynamic mechanical
properties:
— Part 1: General principles
— Part 2: Torsion-pendulum method
— Part 3: Flexural vibration — Resonance-curve method
— Part 4: Tensile vibration — Non-resonance method
— Part 5: Flexural vibration — Non-resonance method
— Part 6: Shear vibration — Non-resonance method
— Part 7: Torsional vibration — Non-resonance method
— Part 8: Longitudinal and shear vibration — Wave-propagation method
— Part 9: Tensile vibration — Sonic-pulse propagation method
— Part 10: Complex shear viscosity using a parallel-plate oscillatory rheometer
Additional parts are planned.
Annexes A and B of this part of ISO 6721 are for information only.
©
ISO 2001 – All rights reserved iii
ISO 6721-1:2001(E)
Introduction
The methods specified in the first nine parts of ISO 6721 can be used for determining storage and loss moduli of
plastics over a range of temperatures or frequencies by varying the temperature of the specimen or the frequency of
oscillation. Plots of the storage or loss moduli, or both, are indicative of viscoelastic characteristics of the specimen.
Regions of rapid changes in viscoelastic properties at particular temperatures or frequencies are normally referred to
as transition regions. Furthermore, from the temperature and frequency dependencies of the loss moduli, the
damping of sound and vibration of polymer or metal-polymer systems can be estimated.
Apparent discrepancies may arise in results obtained under different experimental conditions. Without changing the
observed data, reporting in full (as described in the various parts of ISO 6721) the conditions under which the data
were obtained will enable apparent differences observed in different studies to be reconciled.
The definitions of complex moduli apply exactly only to sinusoidal oscillations with constant amplitude and constant
frequency during each measurement. On the other hand, measurements of small phase angles between stress and
strain involve some difficulties under these conditions. Because these difficulties are not involved in some methods
based on freely decaying vibrations and/or varying frequency near resonance, these methods are used frequently
(see ISO 6721-2 and ISO 6721-3). In these cases, some of the equations that define the viscoelastic properties are
only approximately valid.
©
iv ISO 2001 – All rights reserved
INTERNATIONAL STANDARD ISO 6721-1:2001(E)
Plastics — Determination of dynamic mechanical properties —
Part 1:
General principles
1 Scope
The various parts of ISO 6721 specify methods for the determination of the dynamic mechanical properties of rigid
plastics within the region of linear viscoelastic behaviour. This part of ISO 6721 is an introductory section which
includes the definitions and all aspects that are common to the individual test methods described in the subsequent
parts.
Different deformation modes may produce results that are not directly comparable. For example, tensile vibration
results in a stress which is uniform across the whole thickness of the specimen, whereas flexural measurements are
influenced preferentially by the properties of the surface regions of the specimen.
Values derived from flexural-test data will be comparable to those derived from tensile-test data only at strain levels
where the stress-strain relationship is linear and for specimens which have a homogeneous structure.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 6721. For dated references, subsequent amendments to, or revisions of, any of these publications do
not apply. However, parties to agreements based on this part of ISO 6721 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated references,
the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of
currently valid International Standards.
ISO 291:1997, Plastics — Standard atmospheres for conditioning and testing.
ISO 293:1986, Plastics — Compression moulding test specimens of thermoplastic materials.
ISO 294 (all parts), Plastics — Injection moulding of test specimens of thermoplastic materials.
ISO 295:1991, Plastics — Compression moulding of test specimens of thermosetting materials.
Plastics — Methods of producting test plates.
ISO 1268 (all parts),
ISO 2818:1994, Plastics — Preparation of test specimens by machining.
ISO 4593:1993, Plastics — Film and sheeting — Determination of thickness by mechanical scanning.
ISO 6721-2:1994, Plastics — Determination of dynamic mechanical properties — Part 2: Torsion-pendulum method.
ISO 6721-3:1994, Plastics — Determination of dynamic mechanical properties — Part 3: Flexural vibration —
Resonance-curve method.
©
ISO 2001 – All rights reserved 1
ISO 6721-1:2001(E)
3 Terms and definitions
For the purposes of this part of ISO 6721, the following terms and definitions apply.
N
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.