EN ISO 14113:2008

Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2007)

ISO 14113:2007 specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied and dissolved gases up to a maximum working pressure of 45 MPa (450 bar), within the ambient temperature range of - 20 °C to + 60 °C.
ISO 14113:2007 applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage.
ISO 14113:2007 does not cover rubber or thermoplastic hoses for welding, cutting and allied processes (see ISO 3821 and ISO 12170).
ISO 14113:2007 does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG).

Gasschweißgeräte - Gummi- und Kunststoffschläuche und Schlauchleitungen für Industriegase bis zu einem Druck von 450 bar (45 MPa) (ISO 14113:2007)

In dieser Norm sind Anforderungen für Gummi  und Kunststoffschläuche und Schlau¬chleitungen für Druck  oder Flüssiggase bis zu einem maximalen Betriebsdruck von 450 bar (45 MPa) im Bereich der Umgebungstemperatur zwischen 20 C bis 60 °C festgelegt.
Diese Norm ist anwendbar für Hochdruckschlauchleitungen, welche verwendet werden, um industrielle Gas-flaschen oder Bündel ohne Hauptstellendruckregler zu Batterien zusammenzuschließen.
Diese Norm gilt nicht für thermoplastische Schläuche für Schweißen, Schneiden und verwandte Prozesse (siehe ISO 3821 und ISO 12170).
Diese Norm gilt nicht für tiefkalte ver¬flüssigte Gase oder LPG (Flüssiggas).

Matériel de soudage aux gaz - Tuyaux souples et flexibles en caoutchouc et en plastique pour des gaz industriels jusqu'à 450 bar (45 MPa) (ISO 14113:2007)

L'ISO 14113:2007 spécifie les exigences relatives aux tuyaux souples et flexibles en caoutchouc et en plastique devant être utilisés avec des gaz comprimés, liquéfiés ou dissous jusqu'à une pression maximale de service de 450 bar (45 MPa) à des températures ambiantes comprises entre ‑20 °C et  60 °C.
Elle s'applique aux flexibles utilisés pour relier les bouteilles de gaz industriels aux collecteurs et aux cadres de bouteilles avant toute opération de détente.
Elle ne couvre pas les tuyaux souples en caoutchouc et en matière thermoplastique pour le soudage, le coupage et les techniques connexes (voir l'ISO 3821 et l'ISO 12170).
Elle ne s'applique pas aux gaz liquides cryogéniques ou aux gaz de pétrole liquéfiés (GPL).

Oprema za plamensko varjenje - Cevi in napeljave iz gume in umetnih snovi za tehnične pline do tlaka 450 bar (45 MPa) (ISO 14113:2007)

General Information

• Status: Withdrawn
• Publication Date: 14-Oct-2008
• Withdrawal Date: 01-Oct-2013
• ICS: 23.040.70 - Hoses and hose assemblies
• ICS: 25.160.30 - Welding equipment
• ICS: 83.140.40 - Hoses
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/SC 7 - Equipment for gas welding, cutting and allied processes
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 02-Oct-2013
• Completion Date: 02-Oct-2013
• Ref Project: SIST EN ISO 14113:2009 - Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2007)

Relations

• Replaces: EN ISO 14113:1997 - Gas welding equipment - Rubber and plastic hoses assembled for compressed or liquefied gases up to a maximum design pressure of 450 bar (ISO 14113:1997)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 14113:2013 - Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2013)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 14113:2009
01-april-2009
2SUHPD]DSODPHQVNRYDUMHQMH&HYLLQQDSHOMDYHL]JXPHLQXPHWQLKVQRYL]D
WHKQLþQHSOLQHGRWODNDEDU03D,62
Gas welding equipment - Rubber and plastics hose and hose assemblies for use with
industrial gases up to 450 bar (45 MPa) (ISO 14113:2007)
Gasschweißgeräte - Gummi- und Kunststoffschläuche und Schlauchleitungen für
Industriegase bis zu einem Druck von 450 bar (45 MPa) (ISO 14113:2007)
Matériel de soudage aux gaz - Tuyaux souples et flexibles en caoutchouc et en plastique
pour des gaz industriels jusqu'à 450 bar (45 MPa) (ISO 14113:2007)
Ta slovenski standard je istoveten z: EN ISO 14113:2008
ICS:
25.160.30 Varilna oprema Welding equipment
83.140.40 Gumene cevi Hoses
SIST EN ISO 14113:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 14113:2009

---------------------- Page: 2 ----------------------

SIST EN ISO 14113:2009
EUROPEAN STANDARD
EN ISO 14113
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2008
ICS 83.140.40; 25.160.30 Supersedes EN ISO 14113:1997
English Version
Gas welding equipment - Rubber and plastics hose and hose
assemblies for use with industrial gases up to 450 bar (45 MPa)
(ISO 14113:2007)
Matériel de soudage aux gaz - Tuyaux souples et flexibles Gasschweißgeräte - Gummi- und Kunststoffschläuche und
en caoutchouc et en plastique pour des gaz industriels Schlauchleitungen für Industriegase bis zu einem Druck
jusqu'à 450 bar (45 MPa) (ISO 14113:2007) von 450 bar (45 MPa) (ISO 14113:2007)
This European Standard was approved by CEN on 9 August 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14113:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 14113:2009
EN ISO 14113:2008 (E)
Contents Page
Foreword.3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 14113:2009
EN ISO 14113:2008 (E)
Foreword
The text of ISO 14113:2007 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
14113:2008 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the
latest by April 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14113:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 14113:2007 has been approved by CEN as a EN ISO 14113:2008 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 14113:2009

---------------------- Page: 6 ----------------------

SIST EN ISO 14113:2
...