EN 15347:2007

Plastics - Recycled Plastics - Characterisation of plastics wastes

This European Standard provides a scheme for the characterisation of plastics wastes, laying out those properties for which the supplier of the waste shall make information available to the purchaser, and identifying test methods where applicable. The scheme provides for a division of information between "Required Data", where a statement is required, even if it is "unclassified", and additional "Optional Data" which the supplier may choose to provide if it adds value to the waste.
This standard is applicable without prejudice to any existing legislation.
NOTE   This standard does not cover the characterisation of plastics recyclates.

Kunststoffe - Kunststoff-Rezyklate - Charakterisierung von Kunststoffabfällen

Diese Europäische Norm liefert ein Schema für die Charakterisierung von Kunststoffabfällen, wonach jene Eigenschaften umrissen werden, für die der Lieferant des Abfalls dem Käufer Informationen zugänglich machen und, falls anwendbar, Prüfverfahren für deren Identifizierung angeben muss. Das Schema sorgt für eine Unter¬scheidung der Informationen zwischen „Geforderten Daten“, für die eine Angabe gefordert wird, auch wenn sie „nicht klassifiziert“ lautet, und zusätzlichen „Freiwilligen Daten“, die der Lieferant wahlweise bereitstellen kann, wenn das den Wert des Abfalls erhöht.
Diese Norm beeinträchtigt bei ihrer Anwendung keinerlei geltende Vorschriften.
ANMERKUNG      Die vorliegende Norm befasst sich nicht mit der Charakterisierung von Kunststoff-Rezyklaten.

Plastiques - Plastiques recyclés - Caractérisation des déchets de plastiques

La présente Norme européenne donne un cadre relatif la caractérisation des déchets de plastiques,
présentant des propriétés pour lesquelles le fournisseur de ces déchets doit mettre des informations à la
disposition de l'acheteur, et le cas échéant, identifier des méthodes d'essai. Le cadre scinde les informations
en « Données requises », pour lesquelles un état est demandé, même s'il est « non classé », et en
« Données optionnelles » supplémentaires, que le fournisseur peut choisir de fournir, s'il elles valorisent les
déchets.
La présente norme est applicable sans préjudice de toute réglementation existante.
NOTE La présente norme ne couvre pas la caractérisation des recyclats de plastiques.

Polimerni materiali - Reciklirani polimerni materiali - Karakterizacija odpadkov polimernih materialov

General Information

• Status: Published
• Publication Date: 04-Dec-2007
• Withdrawal Date: 29-Jun-2008
• ICS: 13.030.50 - Recycling
• ICS: 83.080.01 - Plastics in general
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249/WG 11 - Plastics recycling
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 21-Dec-2017
• Ref Project: SIST EN 15347:2008 - Plastics - Recycled Plastics - Characterisation of plastics wastes

Relations

• Revised: FprEN 15347-1 - Plastics - Sorted plastics wastes - Part 1: General characterisation
• Effective Date: 16-Jun-2021

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Plastics - Recycled Plastics - Characterisation of plastics wastesPolimerni materiali - Reciklirani polimerni materiali - Karakterizacija odpadkov polimernih materialovPlastiques - Plastiques recyclés - Caractérisation des déchets de plastiquesKunststoffe - Kunststoff-Rezyklate - Charakterisierung von KunststoffabfällenTa slovenski standard je istoveten z:EN 15347:2007SIST EN 15347:2008en,fr,de83.080.0113.030.50ICS:SLOVENSKI
STANDARDSIST EN 15347:200801-februar-2008







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15347December 2007ICS 13.030.50; 83.080.01 English VersionPlastics - Recycled Plastics - Characterisation of plastics wastesPlastiques - Plastiques recyclés - Caractérisation desdéchets de plastiquesKunststoffe - Kunststoff-Rezyklate - Charakterisierung vonKunststoffabfällenThis European Standard was approved by CEN on 25 October 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15347:2007: E



EN 15347:2007 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms, definitions and abbreviated terms.6 4 Requirements.6 4.1 General.6 4.2 Classification scheme.6 5 Quality Assurance.8 Bibliography.9



EN 15347:2007 (E) 3 Foreword This document (EN 15347:2007) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by June 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This standard is one part of a series of CEN publications on Plastics Recycling which is structured as follows:
 EN 15342 Plastics—Recycled Plastics—Characterization of polystyrene (PS) recyclates  EN 15343 Plastics—Recycled Plastics—Plastics recycling traceability and assessment of conformity and recycled content  EN 15344 Plastics—Recycled Plastics—Characterisation of Polyethylene (PE) recyclates  EN 15345 Plastics—Recycled Plastics—Characterisation of Polypropylene (PP) recyclates  EN 15346 Plastics—Recycled plastics—Cha
...