iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1366-4:2006+A1:2010

(Main)

Fire resistance tests for service installations - Part 4: Linear joint seals

Fire resistance tests for service installations - Part 4: Linear joint seals

This European Standard specifies a method for determining the fire resistance of linear joint seals based on their intended end use. This European Standard is used in conjunction with EN 1363-1.
The following tests are included in this European Standard:
-   no mechanically induced movement;
-   mechanically induced movement, either prior to or during fire exposure.
This European Standard does not provide quantitative information on the rate of leakage of smoke and/or hot gases, or on the transmission or generation of fumes.
The load-bearing capacity of a linear joint seal is not addressed in this European Standard.

Feuerwiderstandsprüfungen für Installationen - Teil 4: Abdichtungssysteme für Bauteilfugen

Diese Europäische Norm legt ein Verfahren zur Bestimmung der Feuerwiderstandsdauer von Fugenabdichtungen
in Abhängigkeit vom beabsichtigten Verwendungszweck fest. Diese Norm gilt zusammen mit
EN 1363-1.
Diese Europäische Norm enthält folgende Prüfungen:
⎯ keine mechanisch induzierte Bewegung;
⎯ mechanisch induzierte Bewegung, entweder vor oder während der Brandeinwirkung.
Eine Prüfung nach dieser Europäischen Norm ergibt keine quantitativen Aussagen zur Leckrate von Rauch
und/oder heißen Gasen oder zur Übertragung bzw. Entwicklung von Rauch.
Die Tragfähigkeit einer Fugenabdichtung ist nicht Gegenstand dieser Europäischen Norm.

Essai de résistance au feu des installations de service - Partie 4: Calfeutrements de joints linéaires

La présente Norme européenne prescrit une méthode pour déterminer la résistance des calfeutrements de joints linéaires en fonction de l’utilisation finale pour laquelle ils sont prévus. La Norme européenne est utilisée conjointement avec l’EN 1363-1.
Les essais suivants sont inclus dans la présente Norme européenne :
—   sans déplacement induit par des actions mécaniques ;
—   avec déplacement induit par des actions mécaniques, avant ou pendant l'exposition au feu.
La présente Norme européenne ne fournit pas d'informations quantitatives relatives au taux de fuite de fumées et/ou de gaz chauds ou à l'émission ou la génération de fumées.
Elle n'aborde pas non plus la capacité portante des calfeutrements de joints linéaires.

Preskusi požarne odpornosti servisnih inštalacij - 4. del: Tesnilna sredstva za ravne stike

Ta evropski standard določa metodo za določanje požarne odpornosti tesnilnih sredstev za ravne stike glede na njihovo končno uporabo. Ta evropski standard se uporablja skupaj z EN 1363-1. Ta evropski standard vključuje naslednje preskuse: - brez mehanično izzvanega premika; - mehanično izzvan premik bodisi pred bodisi med izpostavljenostjo ognju. Ta evropski standard ne zagotavlja kvantitativnih informacij na stopnji puščanja dima in/ali vročih plinov oziroma na prenosu ali sproščanju hlapov. Nosilna zmogljivost tesnilnih sredstev za ravne stike ni obravnavana v tem evropskem standardu.

General Information

Status
Withdrawn
Publication Date
13-Apr-2010
Withdrawal Date
09-Feb-2021
ICS
13.220.50 - Fire-resistance of building materials and elements
Technical Committee
CEN/TC 127 - Fire safety in buildings
Drafting Committee
CEN/TC 127/WG 2 - Services
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
10-Feb-2021
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/BC/CEN/91/9 - CPD: Fire resistance
Ref Project
SIST EN 1366-4:2006+A1:2010 - Fire resistance tests for service installations - Part 4: Linear joint seals

Relations

Merged From
EN 1366-4:2006 - Fire resistance tests for service installations - Part 4: Linear joint seals
Effective Date
19-Jan-2023
Merged From
EN 1366-4:2006/FprA1 - Fire resistance tests for service installations - Part 4: Linear joint seals
Effective Date
18-Jan-2023
Replaced By
EN 1366-4:2021 - Fire resistance tests for service installations - Part 4: Linear joint seals
Effective Date
08-Jun-2022

Buy Standard

EN 1366-4:2006+A1:2010EN 1366-4:2006+A1:2010
PreviousNext
Standard
EN 1366-4:2006+A1:2010
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Preskusi požarne odpornosti servisnih inštalacij - 4. del: Tesnilna sredstva za ravne stikeFeuerwiderstandsprüfungen für Installationen - Teil 4: Abdichtungssysteme für BauteilfugenEssai de résistance au feu des installations de service - Partie 4: Calfeutrements de joints linéairesFire resistance tests for service installations - Part 4: Linear joint seals13.220.50Požarna odpornost gradbenih materialov in elementovFire-resistance of building materials and elementsICS:Ta slovenski standard je istoveten z:EN 1366-4:2006+A1:2010SIST EN 1366-4:2006+A1:2010en,fr01-junij-2010SIST EN 1366-4:2006+A1:2010SLOVENSKI
STANDARD



SIST EN 1366-4:2006+A1:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1366-4:2006+A1
April 2010 ICS 13.220.50 Supersedes EN 1336-4:2006English Version
Fire resistance tests for service installations - Part 4: Linear joint seals
Essai de résistance au feu des installations de service - Partie 4: Calfeutrements de joints linéaires
Feuerwiderstandsprüfungen für Installationen - Teil 4: Abdichtungssysteme für Bauteilfugen This European Standard was approved by CEN on 17 April 2006 and includes Amendment 1 approved by CEN on 4 March 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1366-4:2006+A1:2010: ESIST EN 1366-4:2006+A1:2010



EN 1366-4:2006+A1:2010 (E) 2 Contents Page Foreword .4Introduction .61Scope .72Normative references .73Terms and definitions .74Test equipment .85Test conditions .85.1Heating conditions.85.2Pressure conditions .86Test specimen .86.1General .86.2Size .96.3Number of test specimens .97Installation of test specimen .97.1General .97.2Supporting constr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13501-2:2023(Main)
Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance and/or smoke control tests, excluding ventilation services
SIST EN 13501-2:2023

This document specifies the procedure for classification of construction products and building elements using data from fire resistance and/or smoke leakage/control tests and/or mechanical tests which are within the direct field of application of the relevant test method. Classification on the basis of extended application of test results is also included in the scope of this document.
This document deals with:
a)   loadbearing elements without a fire separating function:
-   walls;
-   floors;
-   roofs;
-   beams;
-   columns;
-   balconies;
-   walkways;
-   stairs.
b)   loadbearing elements with a fire separating function, with or without glazing, services and fixtures:
-   walls;
-   floors;
-   roofs;
-   raised floors.
c)   products and systems for protecting elements or parts of the works:
-   ceilings with no independent fire resistance;
-   fire protective coatings, claddings and screens;
d)   non-loadbearing elements or parts of works, with or without glazing, services and fixtures:
-   partitions;
-   facades (curtain walls) and external walls;
-   ceilings with independent fire resistance;
-   raised floors;
-   fire resisting doorsets, shutter assemblies and openable windows and their closing devices;
-   smoke control doorsets and shutter assemblies and their closing devices;
-   conveyor systems and their closures;
-   penetration seals;
-   linear joint seals;
-   combined penetration seals;
-   service ducts and shafts;
-   air transfer grilles.
-   chimneys.
e)   wall and ceiling coverings with fire protection ability.
f)   lift landing doors which are tested according to EN 81-58 are excluded from this document. Lift landing doors which are tested in accordance with EN 1634-1 are classified in accordance with 7.5.5.
Relevant test methods which have been prepared for these construction products are listed in Clauses 2 and 7.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15725:2023(Main)
Extended application on the fire performance of construction products and building elements: Principle of EXAP standards and EXAP reports
SIST EN 15725:2023

This document gives the procedures for preparing standards and reports following the extended application (EXAP) process using the results of reaction to fire tests, fire resistance tests (including other performance characteristics e.g. smoke leakage/control and/or durability of self-closing), and external fire exposure to roof tests undertaken for fire classification of products and product families in accordance with the various parts of EN 13501. EXAP rules limit the number of tests required by implementing methods to determine the fire classification of a range of products (e.g. range of product, larger dimensions etc.) and EXAP rules form a standardized technical agreement on the parameter changes.
The fundamental concept of EXAP is the development of safe methods that provide extensions to the scope of the tested product while maintaining the required classification for the product. Test reports constitute the basis of an EXAP report.
This document makes reference to ‘extended application standards’ throughout; wherever this term is used it refers to either a standard prepared by CEN/TC 127 ‘Fire safety in buildings’ or the relevant product standard which includes information on extended application.
The European system currently permits extended application rules to be included in technical specifications. CEN Technical Committees and EOTA Working groups producing these rules are asked to seek the guidance of CEN/TC 127 to ensure that their rules comply with standards prepared by CEN/TC 127. In cases where extended application rules in harmonized EN product standards and ETAs do not comply with standards prepared by CEN/TC 127 the CEN BT are informed.
This document does not cover the incorporation of the product into the construction works that is justified by national rules.
Expert judgements (i.e. an opinion that is not considered/covered by an EXAP standard and only based on the experience of one individual) do not form part of this process.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17020-5:2023(Main)
Extended application of test results on durability of self-closing for fire resistance and/or smoke control doorsets and openable windows - Part 5: Durability of self-closing of hinged and pivoted timber doorsets
SIST EN 17020-5:2023

This document is applicable to single and double leaf, hinged and pivoted doorsets with timber-based leaves or timber framed glazed door leaves, covered by EN 15269-3 and / or EN 15269-20.
This document prescribes the methodology for extending the application of test results obtained from durability of self-closing test(s) conducted in accordance with EN 1191 and or EN 12605:2000, as appropriate.
Subject to the completion of the appropriate self-closing test(s), the extended application can cover all or some of the following examples:
-   door leaf; pass doors;
-   glazed doorsets including vision panels and framed glazed doorsets;
-   side, transom and/or overpanels;
-   ventilation grilles and/or louvres;
-   wall or ceiling fixed elements (door frame/suspension system);
-   glazing for door leaf, side, transom and flush over panels;
-   items of building hardware;
-   decorative finishes;
-   intumescent, strips, smoke, draught or acoustic seals;
-   alternative supporting construction(s).

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17020-2:2022(Main)
Extended application of test results on durability of self-closing for fire resistance and/or smoke control doorsets and openable windows - Part 2: Durability of self-closing of steel rolling shutters
SIST EN 17020-2:2023

This document covers steel rolling shutters as covered by EN 15269 10 or EN 15269 20.
This document prescribes the methodology for extending the application of test results obtained from durability self-closing test(s) conducted in accordance with EN 16034.
Subject to the completion of the appropriate self-closing test or tests, the extended application could cover all or some of the following non-exhaustive list:
—   shutter curtain;
—   wall/ceiling fixed elements (frame/suspension system);
—   decorative finishes;
—   intumescent, smoke, draught or acoustic seals;
—   alternative supporting construction(s).

  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13501-6:2018+A1:2022(Main)
Fire classification of construction products and building elements - Part 6: Classification using data from reaction to fire tests on power, control and communication cables
SIST EN 13501-6:2019+A1:2023

This document provides the reaction to fire classification procedure for electric cables.
NOTE   For the purpose of this document, the term "electric cables" covers all power, control and communication cables, including optical fibre cables.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17020-3:2022(Main)
Extended application of test results on durability of self-closing for fire resistance and/or smoke control doorsets and openable windows - Part 3: Durability of self-closing of steel sliding doorsets
SIST EN 17020-3:2023

This document is applicable to the following types of steel based doorsets: horizontally sliding single and double leaf doorsets, horizontally sliding single and double leaf telescopic doorsets, vertically sliding single leaf doorsets and vertically sliding single leaf telescopic doorsets as covered by EN 15269-7 or EN 15269-20.
This document prescribes the methodology for extending the application of test results obtained from durability of self-closing test(s) conducted in accordance with EN 12605:2000 and/or EN 1191.
Subject to the completion of the appropriate durability of self-closing test or tests, the extended application can cover all or some of the following non-exhaustive list:
- door leaf (of the sliding doorset and its pass door);
- integrated pass doors;
- wall or ceiling fixed parts or items of the doorset, e.g. frame or suspension systems;
- ventilation grilles and/or louvres;
- glazing for door leaf;
- items of building hardware;
- decorative finishes;
- intumescent, smoke, draught or acoustic seals;
- alternative supporting construction(s).

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17020-1:2022(Main)
Extended application of test results on durability of self-closing for fire resistance and/or smoke control doorsets and openable windows - Part 1: Durability of self-closing of hinged and pivoted steel doorsets
SIST EN 17020-1:2023

This document covers single and double leaf, hinged and pivoted, steel based doorsets as covered by EN 15269-2 and/or EN 15269-20.
This document prescribes the methodology for extending the application of test results obtained from durability of self-closing test(s) conducted in accordance with EN 1191 and or EN 12605:2000, as appropriate.
Subject to the completion of the appropriate durability of self-closing test(s), the extended application can cover all or some of the following non-exhaustive list:
- door leaf;
- side, transom and/or overpanels;
- ventilation grilles and/or louvres;
- wall or ceiling fixed parts or items of the doorset, e.g. frame or suspensions systems;
- glazing for door leaf, side, transom and flush over panels;
- items of building hardware;
- decorative finishes;
- intumescent strips, smoke, draught or acoustic seals;
- alternative supporting construction(s).

  • Standard
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15269-3:2022(Main)
Extended application of test results for fire resistance and/or smoke control for doorsets, shutter and openable window assemblies, including their elements of building hardware - Part 3: Fire resistance of hinged and pivoted timber doorsets and openable timber framed windows
SIST EN 15269-3:2023

This document covers hinged or pivoted doorsets and door assemblies with wood-based door leaves and/or timber framed glazed door leaves and openable timber framed windows. Throughout this document, the term “doorset” will be used to cover doorsets, door assemblies and openable windows. It prescribes the rules for extending the application of test results obtained from fire resistance test(s) conducted in accordance with EN 1634-1.
This document covers only doorsets with wood-based or metal frames. The door leaves are comprised of wood-based perimeter framing and wood-based structural facings.
Subject to the completion of the appropriate test or tests, the extended application can cover all or some of the following examples:
-   integrity (E), integrity & radiation (EW) or integrity & insulation (EI1 or EI2) classifications;
-   glazing within the doorset, e.g. side and over panels, vision panels and framed glazed doorsets;
-   air transfer grilles (e.g. ventilation grilles/louvres);
-   side, transom or over panels;
-   items of building hardware;
-   decorative and protective finishes;
-   intumescent strips and non-intumescent seals (e.g. smoke, draught or acoustic seals);
-   alternative supporting construction(s).
This document covers only the effect on the fire resistance classifications E, EW, EI1 and EI2.
This document does not cover horizontal doorsets.

  • Standard
    198 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15269-20:2020/AC:2022(Corrigendum)
Extended application of test results for fire resistance and/or smoke control for door, shutter and openable window assemblies, including their elements of building hardware - Part 20: Smoke control for doors, shutters, operable fabric curtains and openable windows
SIST EN 15269-20:2020/AC:2022

This document, which is intended to be read in conjunction with EN 15269 1, covers doors, shutters, openable windows and fabric curtains of any material and of the following types:
-   hinged and pivoted (e.g. metal, timber, framed glazed) doors and openable windows of single or double leaf (Table A.1);
-   horizontally and vertically moving steel sliding doors of single or double leaf with and without pass doors, including telescopic doorsets (Table A.2);
-   metal rolling shutters and operable fabric curtains (excluding overlapping systems) (Table A.3).
The following construction products are not covered by this standard:
-   unframed glass doors and openable windows;
-   sectional doors (including stacking doors);
-   vertically and horizontally folding doors;
-   horizontally and vertically moving timber sliding doors;
-   horizontally and vertically moving framed sliding doors (metal or timber).
In this document, whenever doors are mentioned, the whole range of doors, shutters, openable windows and operable fabric curtains is included or otherwise mentioned.
This document prescribes the methodology for extending the application of test results obtained from test(s) conducted in accordance with EN 1634 3.
Subject to the completion of the appropriate test or tests, the extended application can cover all or some of the following examples:
-   Ambient Temperature Smoke Control (Sa) and Medium Temperature Smoke Control (S200) classifications;
-   leaf/leaves;
-   wall/ceiling fixed elements;
-   glazed elements, louvres and/or vents;
-   side, transom or overpanels;
-   items of building hardware;
-   decorative finishes;
-   intumescent, smoke, draught or acoustic seals;
-   alternative supporting construction(s).

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1366-10:2022(Main)
Fire resistance tests for service installations - Part 10: Smoke control dampers
SIST EN 1366-10:2022

This document specifies test methods for smoke control dampers to assess their performance under elevated temperature or fire conditions, as well as at ambient temperatures.
Smoke control damper tests are used to confirm that the furnace testing requirements of EN 12101-8 are met and EN 12101-8 is for consideration before carrying out these tests.
Smoke control dampers tested to this document are expected to be classified using EN 13501-4 and this document is expected to be considered before carrying out these tests.
NOTE   Some smoke control dampers to be tested might require testing following the information given in EN 1366-2 and this needs consideration before carrying out testing.
This document is expected to be read in conjunction with EN 12101-8, EN 13501-4, EN 1366-2 and EN 1363-1, the latter giving further details for fire resistance testing.
For installation details, the requirements for smoke extraction ducts are for consideration and these are defined in EN 1366-8 and EN 1366-9.

  • Standard
    100 pages
    English language
    sale 10% off
    e-Library read for
    1 day