EN ISO 15083:2003
(Main)Small craft - Bilge-pumping systems (ISO 15083:2003)
Small craft - Bilge-pumping systems (ISO 15083:2003)
ISO 15083:2003 specifies requirements for pumping or alternative means designed to remove normal accumulations of bilge water for small craft with a hull length up to 24 m according to ISO 8666.
ISO 15083:2003 does not set requirements for bilge pumps or bilge-pumping systems designed for damage control.
Kleine Wasserfahrzeuge - Lenzeinrichtungen (ISO 15083:2003)
Diese Internationale Norm legt Anforderungen für das Abpumpen oder alternative Möglichkeiten zum Entfernen von üblichen Mengen von Wasser fest, das sich üblicherweise in der Bilge ansammelt. Sie gilt für kleine Wasserfahrzeuge mit einer Rumpflänge LH bis 24 m nach ISO 8666.
Diese Internationale Norm legt keine Anforderungen für Lenzpumpen oder Lenzeinrichtungen zum Zwecke der Leckbegrenzung fest.
Navires de plaisance - Systèmes de pompage de cale (ISO 15083:2003)
L'ISO 15083:2003 spécifie les exigences relatives au pompage ou aux autres moyens utilisés pour lutter contre l'accumulation normale d'eau dans la cale des petits navires d'une longueur de coque inférieure ou égale à 24 m, mesurée conformément à l'ISO 8666.
L'ISO 15083:2003 n'établit pas d'exigences pour les pompes de cale ou les systèmes de pompes de cale destinés à contrôler l'eau provenant d'une avarie.
Mala plovila - Kalužni sistemi (na čolnih) (ISO 15083:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2004
0DODSORYLOD.DOXåQLVLVWHPLQDþROQLK,62
Small craft - Bilge-pumping systems (ISO 15083:2003)
Kleine Wasserfahrzeuge - Lenzeinrichtungen (ISO 15083:2003)
Navires de plaisance - Systemes de pompage de cale (ISO 15083:2003)
Ta slovenski standard je istoveten z: EN ISO 15083:2003
ICS:
47.080
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 15083
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2003
ICS 47.080
English version
Small craft - Bilge-pumping systems (ISO 15083:2003)
Navires de plaisance - Systèmes de pompage de cale (ISO Kleine Wasserfahrzeuge - Lenzeinrichtungen (ISO
15083:2003) 15083:2003)
This European Standard was approved by CEN on 11 December 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15083:2003 E
worldwide for CEN national Members.
CORRECTED 2003-03-26
Foreword
This document (EN ISO 15083:2003) has been prepared by Technical Committee ISO/TC 188 "Small craft", the
secretariat of which is held by CMC.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by August 2003, and conflicting national standards shall be withdrawn at the latest by
August 2003.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,
Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15083:2003 has been approved by CEN as EN ISO 15083:2003 without any modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated
references, subsequent amendments to or revisions of any of these publications apply to this European Standard only
when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred
to applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated by (mod.), the
relevant EN/HD applies.
Publication Year Title EN Year
ISO 8666 2002 Small craft - Principal data EN ISO 8666 2002
ISO 8849 1990 Small craft — Electrically operated bilge-pumps EN 28849 1993
ISO 9093-1 1994 Small craft — Seacocks and through-hull fittings EN ISO 9093-1 1997
— Part 1: Metallic
ISO 9093-2 2002 Small craft - Seacocks and through-hull fittings - EN ISO 9093-2 2002
Part 2: Non-metallic
ISO 11812 2001 Small craft — Watertight cockpits and quick- EN ISO 11812 2001
draining cockpits
ISO 12216 2002 Small craft — Windows, portlights, hatches, EN ISO 12216 2002
deadlights and doors — Strength and
watertightness requirements
Annex ZB
(informative)
Clauses of this European Standard addressing essential requirements or other
provisions of EU Directives
This European Standard has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association and supports essential requirements of EU Directive 94/25/EC.
WARNING: Other requirements and other EU Directive may be applicable to the product(s) falling within the
scope of this standard.
The following clauses of this standard, as detailed in Table ZB.1, are likely to support requirements of Directive
94/25/EC.
Compliance with the clauses of this standard provides one means of conforming with the specific essential
requirements of the Directive concerned and associated EFTA regulations.
Table ZB.1: Correspondence between this European Standard and EU Directives
Clauses/sub-clauses of this Corresponding annexes/paragraphs Comments
European Standard of Directive 94/25/EC
All Clauses Annex I, Clause 3.5
Clause 8, Annex A Annex I, Clause 2.5
INTERNATIONAL ISO
STANDARD 15083
First edition
2003-02-01
Small craft — Bilge-pumping systems
Petits navires — Systèmes de pompes de cale
Reference number
ISO 15083:2003(E)
©
ISO 2003
ISO 15083:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved
ISO 15083:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Symbols. 3
5 Requirements. 4
5.1 Type, number and location . 4
5.2 Summary of requirements. 5
5.3 Capacity. 5
6 Design and construction. 6
6.1 General. 6
6.2 Electrically operated pumps . 6
7 Installation. 6
8 Owner’s manual. 7
Annex A (normative) Information to be provided in the owner’s manual . 8
ISO 15083:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15083 was prepared by Technical Committee ISO/TC 188, Small craft.
iv © ISO 2003 — All rights reserved
ISO 15083:2003(E)
Introduction
Bilge-pumping systems as specified in this International Standard are limited to normal amounts of water in an
intact boat due to spray, rain, seepage, spillage, and occasional small amounts of water shipped from boat
movements in heavy weather.
This International Standard is not intended to enable flooding resulting from hull damage, to be dealt with.
INTERNATIONAL STANDARD ISO 15083:2003(E)
Small craft — Bilge-pumping systems
1 Scope
This International Standard specifies requirements for pumping or alternative means designed to remove
normal accumulations of bilge water for small craft with a hull length, L , up to 24 m according to ISO 8666.
H
This International Standard does not set requirements for bilge pumps or bilge-pumping systems designed for
damage control.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 8666:2002, Small craft — Principal data
1)
ISO 8849:— , Small craft — Electrically operated bilge-pumps
ISO 9093 (all parts), Small craft — Seacocks and through-hull fittings
ISO 11812:2001, Small craft — Watertight cockpits and quick-draining cockpits
ISO 12216:2002, Small craft — Windows, portlights, hatches, deadlights and doors — Strength and
watertightness requirements
IEC 60529: 2001, Degrees of protection provided by enclosures (IP Code)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply. The meanings of symbols used
in the definitions are given in Clause 4.
3.1
design category
description of the sea and wind conditions for which a boat is assessed to be suitable
3.1.1
design category A
category for “ocean” sailing
boat designed for extended voyages where conditions experienced may exceed wind force 8 (Beaufort Scale)
and significant wave heights of 4 m and above, but excluding abnormal conditions (e.g. hurricanes)
1) To be published. (Revision of ISO 8849:1990)
ISO 15083:2003(E)
3.1.2
design category B
category for “offshore” sailing
boat designed for offshore voyages where conditions up to and including wind force 8 (Beaufort Scale) and
significant wave heights up to and including 4 m may be experienced
3.1.3
design category C
category for “inshore” sailing
boat designed for voyages in coastal waters, large bays, estuaries, lakes and rivers, where conditions up to
and including wind force 6 (Beaufort Scale) and significant wave heights up to and including 2 m may be
experienced
3.1.4
design category D
category for sailing in “sheltered waters”
boat design
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.