EN 14121:2009

Aluminium and aluminium alloys - Sheet, strip and plate for electrotechnical applications

This European Standard specifies the technical conditions for inspection and delivery, the mechanical properties and
electrical conductivity of wrought aluminium sheet, strip and plate for electrotechnical applications such as bus bars
and other conductors, products requiring a certain minimum electrical conductivity.
It applies to products with a thickness over 0,20 mm up to and including 150 mm.

Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten für elektrotechnische Anwendungen

Diese Europäische Norm legt die technischen Lieferbedingungen, die mechanischen Eigenschaften und die
elektrische Leitfähigkeit für Bänder, Bleche und Platten aus Aluminium und Aluminiumlegierungen für elektrotechnische Anwendungen fest, wie z. B. Stromschienen und andere Leiter, d. h. Erzeugnisse, die eine elektrische Mindestleitfähigkeit aufweisen müssen.
Sie gilt für Erzeugnisse mit einer Dicke von 0,20 mm bis 150 mm.

Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses pour applications électrotechniques

La présente Norme européenne spécifie les conditions techniques de contrôle et de livraison, les caractéristiques mécaniques et la conductivité électrique des tôles, bandes et tôles épaisses en aluminium et alliages d’aluminium corroyés pour applications électrotechniques telles que barres omnibus et autres conducteurs, produits exigeant une conductivité électrique minimale.
Elle s’applique aux produits d’une épaisseur supérieure à 0,20 mm, jusqu’à 150 mm inclus.

Aluminij in aluminijeve zlitine - Debela in tanka aluminijska pločevina ter trakovi za elektrotehniko

General Information

• Status: Published
• Publication Date: 26-May-2009
• Withdrawal Date: 29-Nov-2009
• ICS: 77.150.10 - Aluminium products
• Technical Committee: CEN/TC 132 - Aluminium and aluminium alloys
• Drafting Committee: CEN/TC 132/WG 7 - Sheets, strips and plates
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 20-May-2021
• Ref Project: SIST EN 14121:2009 - Aluminium and aluminium alloys - Aluminium sheet, strip and plate for electrotechnical applications

Relations

• Replaces: EN 14121:2003 - Aluminium and aluminium alloys - Aluminium sheet, strip and plate for electrotechnical applications
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.HOHNWURWHKQLNRAluminium und Aluminiumlegierungen - Bänder, Bleche und Platten aus Aluminium für elektrotechnische AnwendungenAluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses en aluminium pour applications électrotechniquesAluminium and aluminium alloys - Aluminium sheet, strip and plate for electrotechnical applications77.150.10Aluminijski izdelkiAluminium productsICS:Ta slovenski standard je istoveten z:EN 14121:2009SIST EN 14121:2009en,fr,de01-september-2009SIST EN 14121:2009SLOVENSKI
STANDARDSIST EN 14121:20041DGRPHãþD



SIST EN 14121:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14121May 2009ICS 77.150.10Supersedes EN 14121:2003
English VersionAluminium and aluminium alloys - Sheet, strip and plate forelectrotechnical applicationsAluminium et alliages d'aluminium - Tôles, bandes et tôlesépaisses pour applications électrotechniquesAluminium und Aluminiumlegierungen - Bänder, Blecheund Platten für elektrotechnische AnwendungenThis European Standard was approved by CEN on 24 April 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14121:2009: ESIST EN 14121:2009



EN 14121:2009 (E)
2 Contents Foreword . 31Scope . 42Normative references . 43Terms and definitions . 44Ordering information . 45Requirements . 55.1Production and manufacturing processes . 55.2Quality control . 55.3Chemical composition . 55.4Mechanical properties and electrical conductivity . 65.5Freedom from defects . 75.6Tolerances on dimensions and form . 75.7Other properties . 76Test methods . 76.1Chemical composition . 76.2Tensile test . 76.3Electrica
...