iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1594:2000

(Main)

Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements

Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements

This European Standard is applicable to pipelines with a maximum operating pressure (MOP) over 16 bar for the carriage of processed, non-toxic and non-corrosive natural gas according to ISO 13686 in onland gas supply systems, where: - the pipeline elements are made of unalloyed or low-alloyed carbon steel; - the pipeline elements are joined by welds, flanges or mechanical couplings;

Gasversorgungssysteme - Rohrleitungen für einen maximal zulässigen Betriebsdruck über 16 bar - Funktionale Anforderungen

Diese Europäische Norm gilt für Leitungen mit einem maximal zulässigen Betriebsdruck (MOP) im Bereich von über 16 bar, die für den Transport von aufbereitetem, nicht giftigem und nicht korrosivem Erdgas entsprechend ISO 13686 auf dem Festland bestimmt sind und bei denen: - die Leitungsbauteile aus nicht legiertem oder niedrig legiertem Kohlenstoffstahl bestehen; - die Leitungsbauteile durch Schweißnähte, Flansche oder mechanische Rohrverbindungen miteinander verbunden sind;...

Systèmes d'alimentation en gaz - Canalisations pour pression maximale de service supérieure à 16 bar - Prescriptions fonctionnelles

La présente norme s'applique aux canalisations utilisées sous une pression maximale de service (MOP) supérieure à 16 bar pour le transport de gaz naturel traité non toxique et non corrosif conformément à l'ISO 13686 dans des systèmes d'alimentation en gaz terrestres dont: - les éléments de canalisations sont en acier non ou faiblement allié; - les éléments de canalisations sont réunis par des soudures, des brides ou des assemblages mécaniques;

Sistemi oskrbe s plinom - Cevovodni sistemi za najvišji delovni tlak nad 16 bar - Funkcionalne zahteve

General Information

Status
Withdrawn
Publication Date
21-Mar-2000
Withdrawal Date
20-Jan-2009
ICS
23.040.01 - Pipeline components and pipelines in general
75.200 - Petroleum products and natural gas handling equipment
Technical Committee
CEN/TC 234 - Gas infrastructure
Drafting Committee
CEN/TC 234/WG 3 - Gas Transportation
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
21-Jan-2009
Completion Date
21-Jan-2009
Directive
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/017 - Standardization mandate to CEN in the field of equipment and installation for the transmission and distribution of gas
Ref Project
SIST EN 1594:2000 - Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements

Relations

Child
EN 12732:2000 - Gas supply systems - Welding steel pipework - Functional requirements
Effective Date
22-Dec-2008
Replaced By
EN 1594:2009 - Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements
Effective Date
28-Jan-2009

Buy Standard

EN 1594:2000EN 1594:2000
PreviousNext
Standard
EN 1594:2000
English language
97 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sistemi oskrbe s plinom - Cevovodni sistemi za najvišji delovni tlak nad 16 bar - Funkcionalne zahteveGasversorgungssysteme - Rohrleitungen für einen maximal zulässigen Betriebsdruck über 16 bar - Funktionale AnforderungenSystemes d'alimentation en gaz - Canalisations pour pression maximale de service supérieure a 16 bar - Prescriptions fonctionnellesGas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements91.140.40Sistemi za oskrbo s plinomGas supply systemsICS:Ta slovenski standard je istoveten z:EN 1594:2000SIST EN 1594:2000en01-julij-2000SIST EN 1594:2000SLOVENSKI
STANDARD



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN 1594:2000



SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17649:2022(Main)
Gas infrastructure - Safety Management System (SMS) and Pipeline Integrity Management System (PIMS) - Functional requirements
SIST EN 17649:2022

This document specifies requirements on the development and implementation of a Safety Management System (SMS) and a Pipeline Integrity Management System (PIMS). The SMS is applicable for system operators of a gas infrastructure. The PIMS is applicable for system operators of gas infrastructure with a maximum operating pressure (MOP) over 16 bar.
This document refers to all activities and processes related to safety aspects and performed by system operators of a gas infrastructure, including those activities entrusted to contractors. It includes safety-related provisions on operation of the gas infrastructure.
This document is applicable to infrastructure for the conveyance of processed, non-toxic and non-corrosive natural gas according to EN ISO 13686 and gases such as biomethane and hydrogen and to mixtures of these gases with natural gas.
This document covers also gases classified as group H, that are to be transmitted, injected into and from storages, distributed and utilized, as specified in EN 16726. For the requirements and test methods for biomethane at the point of entry into a natural gas network, reference is made to EN 16723-1.
This document can be applied for gas infrastructure conveying gases of the 3rd gas family as classified in EN 437 or for other gases such as carbon dioxide.
Specific requirements for occupational health and safety are excluded from this document. For these, other European and/or international standards, e.g. ISO 45001, apply.
This document specifies common basic principles for gas infrastructure. It is important that users of this document are expected to be aware that more detailed national standards and/or codes of practice exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this document, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).
NOTE CEN/TR 13737 (all parts) contains:
- clarification of relevant legislation/regulations applicable in a country;
- if appropriate, more restrictive national requirements;
- national contact points for the latest information.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1594:2013(Main)
Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements
SIST EN 1594:2013

This European Standard is applicable to pipelines with a maximum operating pressure (MOP) over 16 bar for the carriage of processed, non-toxic and non-corrosive natural gas according to EN ISO 13686 in onland gas infrastructure.
This European Standard is also applicable to pipelines with a maximum operating pressure (MOP) over 16 bar for the carriage of non-conventional gases such as injected biomethane, complying with EN ISO 13686 and for which a detailed technical evaluation of the functional requirements is performed ensuring there are no other constituents or properties of the gases that can affect the integrity of the pipeline.
Onland gas infrastructure is where:
-   pipeline elements are made of unalloyed or low-alloyed carbon steel;
-   pipeline elements are joined by welds, flanges or mechanical couplings;
-   the pipeline is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises;
-   the design temperature of the system is between −40 °C and 120 °C inclusive.
This European Standard applies to onshore pipeline systems from the point where the pipeline first crosses what is normally accepted as battery limit between on and offshore, e.g.:
-   first isolation valve;
-   the base of steep sea shelf;
-   above the high water/low water mark onto mainland;
-   an island.
This European Standard also applies to a pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes etc.
This European Standard does not apply to existing pipelines, in use prior to the publication of this European Standard, nor to modifications to existing pipelines.
Gas infrastructures covered by this European Standard begin after the gas producer's metering station. The functional demarcation of the pipeline system within a plant area will be determined from case to case. Generally speaking, this will be directly after the first isolating valve of the installation.
This European Standard also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar. Welding requirements are described in a special application standard on welding for gas infrastructures EN 12732. Functional requirements for stations are given in:
-   EN 1776, Gas supply systems — Natural gas measuring stations — Functional requirements
-   EN 1918 5, Gas supply systems — Underground gas storage — Part 5: Functional recommendations for surface facilities
-   EN 12186, Gas supply systems — Gas pressure regulating stations for transmission and distribution — Functional requirements
-   EN 12583, Gas supply systems — Compressor stations — Functional requirements
This European Standard specifies common basic principles for gas infrastructures. Users of this European Standard should be aware that there may exist more detailed national standards and codes of practice in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above mentioned principles.
In the event of conflicts in terms of more restrictive requirements in the national legislation/regulation with the requirements of this European Standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).
NOTE   CEN/TR 13737 (all parts) contains:
-   clarification of relevant legislation/regulations applicable in a country;
-   if appropriate, more restrictive national requirements;
-   national contact point for the latest information.
Reference is made in this European Standard to relevant European and other recognised standards for products used to construct and operate gas infrastructures.
A schematic representation of pipelines for gas transmission is given in Figure 1.

  • Standard
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 1594(Main)
Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements
kSIST FprEN 1594:2023

This document describes the functional requirements for pipelines for maximum operating pressure over 16 bar. This document also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar.
NOTE 1   Welding requirements are described in EN 12732. Functional requirements for stations are given in EN 1776, EN 1918-5, EN 12186, and EN 12583.
This document is applicable for transporting gas via onshore high-pressure steel pipeline infrastructures, where the following applies:
-   onshore:
-   from the point where the pipeline first crosses what is normally accepted as battery limit between onshore and offshore, and that is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises;
-   pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes, etc.
-   high pressure: gas with a maximum operating pressure over 16 bar and a design temperature between −40 °C and 120 °C.
-   steel pipeline infrastructure: infrastructure consisting of pipeline components, such as pipes, valves, couplings and other equipment, restricted to components made of unalloyed or low alloyed carbon steel and joined by welds, flanges or mechanical couplings.
-   gas: non-corrosive natural gas, biomethane gas, hydrogen gas and mixtures of these gases where technical evaluation has ensured that operating conditions or constituents or properties of the gas do not affect the safe operation of the pipeline.
Gas infrastructures covered by this document begin after the gas producer's metering station.
NOTE 2   The functional demarcation of the pipeline system is usually directly after an isolating valve of the installation, but can differ in particular situations. The functional demarcation of the pipeline system is usually located on an isolating valve of the installation, but can differ in particular situations.
A schematic representation of pipelines for gas infrastructure is given in Figure 1.
This document can also be applied to the repurposing of existing pipelines.
[Figure 1 - Schematic representation of pipelines for gas supply over 16 bar]
This document specifies common basic principles for gas infrastructure. Users of this standard are expected to be aware that more detailed national standards and/or code of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737.
CEN/TR 13737 gives:
-   clarification of all legislations/regulations applicable in a member state;
-   if appropriate, more restrictive national requirements;
-   a national contact point for the latest information.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17649:2022(Main)
Gas infrastructure - Safety Management System (SMS) and Pipeline Integrity Management System (PIMS) - Functional requirements
SIST EN 17649:2022

This document specifies requirements on the development and implementation of a Safety Management System (SMS) and a Pipeline Integrity Management System (PIMS). The SMS is applicable for system operators of a gas infrastructure. The PIMS is applicable for system operators of gas infrastructure with a maximum operating pressure (MOP) over 16 bar.
This document refers to all activities and processes related to safety aspects and performed by system operators of a gas infrastructure, including those activities entrusted to contractors. It includes safety-related provisions on operation of the gas infrastructure.
This document is applicable to infrastructure for the conveyance of processed, non-toxic and non-corrosive natural gas according to EN ISO 13686 and gases such as biomethane and hydrogen and to mixtures of these gases with natural gas.
This document covers also gases classified as group H, that are to be transmitted, injected into and from storages, distributed and utilized, as specified in EN 16726. For the requirements and test methods for biomethane at the point of entry into a natural gas network, reference is made to EN 16723-1.
This document can be applied for gas infrastructure conveying gases of the 3rd gas family as classified in EN 437 or for other gases such as carbon dioxide.
Specific requirements for occupational health and safety are excluded from this document. For these, other European and/or international standards, e.g. ISO 45001, apply.
This document specifies common basic principles for gas infrastructure. It is important that users of this document are expected to be aware that more detailed national standards and/or codes of practice exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this document, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).
NOTE CEN/TR 13737 (all parts) contains:
- clarification of relevant legislation/regulations applicable in a country;
- if appropriate, more restrictive national requirements;
- national contact points for the latest information.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14692-4:2017(Main)
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2017)
SIST EN ISO 14692-4:2017

ISO 14692-4:2017 gives requirements and recommendations for the fabrication, installation, inspection and maintenance of GRP piping systems for use in oil and natural gas industry processing and utility service applications. The recommendations apply to delivery, inspection, handling, storage, installation, system pressure testing, maintenance and repair.
It is intended to be read in conjunction with ISO 14692‑1.

  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14692-2:2017(Main)
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2017)
SIST EN ISO 14692-2:2017

ISO 14692-2:2017 gives requirements for the qualification and manufacture of GRP piping and fittings in order to enable the purchase of GRP components with known and consistent properties from any source.
It is applicable to qualification procedures, preferred dimensions, quality programmes, component marking and documentation.
ISO 14692-2:2017 is intended to be read in conjunction with ISO 14692‑1.

  • Standard
    89 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    91 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14692-3:2017(Main)
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2017)
SIST EN ISO 14692-3:2017

ISO 14692-3:2017 gives guidelines for the design of GRP piping systems. The requirements and recommendations apply to layout dimensions, hydraulic design, structural design, detailing, fire endurance, spread of fire and emissions and control of electrostatic discharge.
This document is intended to be read in conjunction with ISO 14692‑1.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14692-1:2017(Main)
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2017)
SIST EN ISO 14692-1:2017

ISO 14692-1:2017 defines the applications, pressure rating methodology, the classification of the products according to application, type of joint and resin matrix and the limitations to both the materials of construction and the dimensions. It also lists the terms, definitions and symbols used and provides guidance in the use and interpretation of ISO 14692-2, ISO 14692-3 and ISO 14692-4.
ISO 14692 (all parts) is applicable to GRP piping systems that 1) utilize joints that are capable of restraining axial thrust from internal pressure, temperature change and fluid hydrodynamic forces and 2) have a trapezoidal shape for its design envelope. It is primarily intended for offshore applications on both fixed and floating topsides facilities, but it can also be used for the specification, manufacture, testing and installation of GRP piping systems in other similar applications found onshore, e.g. produced-water, firewater systems and general industrial use.
For floating installations, reference is made to the design, construction and certification standards for the hull or vessel, since these can allow alternative codes and standards for GRP piping associated with marine and/or ballast systems. However, it is recommended that ISO 14692 (all parts) be used for such applications to the maximum degree attainable.
ISO 14692 (all parts) can also be used as the general basis for specification of pipe used for pump caissons, stilling tubes, I-tubes, seawater lift risers and other similar items.

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    75 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1594:2013(Main)
Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements
SIST EN 1594:2013

This European Standard is applicable to pipelines with a maximum operating pressure (MOP) over 16 bar for the carriage of processed, non-toxic and non-corrosive natural gas according to EN ISO 13686 in onland gas infrastructure.
This European Standard is also applicable to pipelines with a maximum operating pressure (MOP) over 16 bar for the carriage of non-conventional gases such as injected biomethane, complying with EN ISO 13686 and for which a detailed technical evaluation of the functional requirements is performed ensuring there are no other constituents or properties of the gases that can affect the integrity of the pipeline.
Onland gas infrastructure is where:
-   pipeline elements are made of unalloyed or low-alloyed carbon steel;
-   pipeline elements are joined by welds, flanges or mechanical couplings;
-   the pipeline is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises;
-   the design temperature of the system is between −40 °C and 120 °C inclusive.
This European Standard applies to onshore pipeline systems from the point where the pipeline first crosses what is normally accepted as battery limit between on and offshore, e.g.:
-   first isolation valve;
-   the base of steep sea shelf;
-   above the high water/low water mark onto mainland;
-   an island.
This European Standard also applies to a pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes etc.
This European Standard does not apply to existing pipelines, in use prior to the publication of this European Standard, nor to modifications to existing pipelines.
Gas infrastructures covered by this European Standard begin after the gas producer's metering station. The functional demarcation of the pipeline system within a plant area will be determined from case to case. Generally speaking, this will be directly after the first isolating valve of the installation.
This European Standard also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar. Welding requirements are described in a special application standard on welding for gas infrastructures EN 12732. Functional requirements for stations are given in:
-   EN 1776, Gas supply systems — Natural gas measuring stations — Functional requirements
-   EN 1918 5, Gas supply systems — Underground gas storage — Part 5: Functional recommendations for surface facilities
-   EN 12186, Gas supply systems — Gas pressure regulating stations for transmission and distribution — Functional requirements
-   EN 12583, Gas supply systems — Compressor stations — Functional requirements
This European Standard specifies common basic principles for gas infrastructures. Users of this European Standard should be aware that there may exist more detailed national standards and codes of practice in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above mentioned principles.
In the event of conflicts in terms of more restrictive requirements in the national legislation/regulation with the requirements of this European Standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).
NOTE   CEN/TR 13737 (all parts) contains:
-   clarification of relevant legislation/regulations applicable in a country;
-   if appropriate, more restrictive national requirements;
-   national contact point for the latest information.
Reference is made in this European Standard to relevant European and other recognised standards for products used to construct and operate gas infrastructures.
A schematic representation of pipelines for gas transmission is given in Figure 1.

  • Standard
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13942:2009/AC:2009(Corrigendum)
Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified/Cor 1:2009)
SIST EN 13942:2009/AC:2009

ISO - Taking over of an ISO Technical Corrigendum in an ISO modified EN

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day