EN ISO 14253-1:1998/prA1
(Amendment)Geometrical Product Specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 1: Decision rules for proving conformance or non-conformance with specifications (ISO 14253-1:1998/DAM 1:2012)
Geometrical Product Specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 1: Decision rules for proving conformance or non-conformance with specifications (ISO 14253-1:1998/DAM 1:2012)
2013-02-14 EMA: WI deleted due to cancellation of equivalent ISO project. ISO decided to launch a revision instead, see new WI 00290191
2013-01-25 EMA: Draft for // vote received in ISO/CS (see notification of 2013-01-25 in dataservice)
2011-11-22 EMA: Draft for // ENQ received in ISO/CS (see notification of 2011-11-21 in dataservice).
Geometrische Produktspezifikationen (GPS) - Prüfung von Werkstücken und Meßgeräten durch Messen - Teil 1: Entscheidungsregeln für die Feststellung von Übereinstimmung oder Nichtübereinstimmung mit Spezifikationen (ISO 14253-1:1998/DAM 1:2012)
Spécification géométrique des produits (GPS) - Vérification par la mesure des pièces et des équipements de mesure - Partie 1: Règles de décision pour prouver la conformité ou la non-conformité à la spécification (ISO 14253-1:1998/DAM 1:2012)
Specifikacija geometrijskih veličin izdelka - Nadzor izdelkov in merilne opreme z merjenjem - 1. del: Pravila odločanja pri ugotavljanju skladnosti ali neskladnosti s specifikacijami (ISO 14253-1:1998/DAM 1:2012)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2012
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND1DG]RUL]GHONRYLQPHULOQHRSUHPH]
PHUMHQMHPGHO 3UDYLODRGORþDQMDSULXJRWDYOMDQMXVNODGQRVWLDOLQHVNODGQRVWLV
VSHFLILNDFLMDPL ,62 '$0
Geometrical Product Specifications (GPS) - Inspection by measurement of workpieces
and measuring equipment - Part 1: Decision rules for proving conformance or non-
conformance with specifications (ISO 14253-1:1998/DAM 1:2012)
Geometrische Produktspezifikationen (GPS) - Prüfung von Werkstücken und
Meßgeräten durch Messen - Teil 1: Entscheidungsregeln für die Feststellung von
Übereinstimmung oder Nichtübereinstimmung mit Spezifikationen (ISO 14253-
1:1998/DAM 1:2012)
Spécification géométrique des produits (GPS) - Vérification par la mesure des pièces et
des équipements de mesure - Partie 1: Règles de décision pour prouver la conformité ou
la non-conformité à la spécification (ISO 14253-1:1998/DAM 1:2012)
Ta slovenski standard je istoveten z: EN ISO 14253-1:1998/prA1
ICS:
17.040.10 Tolerance in ujemi Limits and fits
17.040.30 Merila Measuring instruments
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
DRAFT
EN ISO 14253-1:1998
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2012
ICS 17.040.30
English Version
Geometrical Product Specifications (GPS) - Inspection by
measurement of workpieces and measuring equipment - Part 1:
Decision rules for proving conformance or non-conformance with
specifications (ISO 14253-1:1998/DAM 1:2012)
Spécification géométrique des produits (GPS) - Vérification Geometrische Produktspezifikationen (GPS) - Prüfung von
par la mesure des pièces et des équipements de mesure - Werkstücken und Meßgeräten durch Messen - Teil 1:
Partie 1: Règles de décision pour prouver la conformité ou Entscheidungsregeln für die Feststellung von
la non-conformité à la spécification (ISO 14253- Übereinstimmung oder Nichtübereinstimmung mit
1:1998/DAM 1:2012) Spezifikationen (ISO 14253-1:1998/DAM 1:2012)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 290.
This draft amendment A1, if approved, will modify the European Standard EN ISO 14253-1:1998. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14253-1:1998/prA1:2012: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 14253-1:1998/prA1:2012) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 14253-1:1998/DAM 1:2012 has been approved by CEN as a EN ISO 14253-1:1998/prA1:2012
without any modification.
DRAFT AMENDMENT ISO 14253-1:1998/DAM 1
ISO/TC 213 Secretariat: DS
Voting begins on Voting terminates on
2012-02-02 2012-07-02
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Geometrical Product Specifications (GPS) — Inspection by
measurement of workpieces and measuring equipment —
Part 1:
Decision rules for proving conformance or non-conformance
with specifications
AMENDMENT 1
Spécification géométrique des produits (GPS) — Vérification par la mesure des pièces et des équipements de
mesure —
Partie 1: Règles de décision pour prouver la conformité ou la non-conformité à la spécification
AMENDEMENT 1
ICS 17.040.01
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.