EN ISO 14660-2:1999/prA1
(Amendment)Geometrical Product Specifications (GPS) - Geometrical features - Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature (ISO 14660-2:1999/DAM 1:2010)
Geometrical Product Specifications (GPS) - Geometrical features - Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature (ISO 14660-2:1999/DAM 1:2010)
2013-02-19: WI deleted due to cancellation of equivalent ISO Project
Geometrische Produktspezifikation (GPS) - Geometrieelemente - Teil 2: Erfasste mittlere Linie eines Zylinders und eines Kegels, erfasste mittlere Fläche, örtliches Maß eines erfassten Geometrieelementes (ISO 14660-2:1999/DAM 1:2010)
Spécification géométrique des produits (GPS) - Éléments géométriques - Partie 2: Ligne médiane extraite d'un cylindre et d'un cône, surface médiane extraite, taille locale d'un élément extrait (ISO 14660-2:1999/DAM 1:2010)
Specifikacija geometrijskih veličin izdelka - Geometrijske značilnosti - 2. del: Povzeta srednja linija valja in stožca, povzeta srednja površina, lokalna velikost povzete značilnosti (ISO 14660-2:1999/DAM 1:2010)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14660-2:2002/oprA1:2010
01-december-2010
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND*HRPHWULMVNH]QDþLOQRVWLGHO
3RY]HWDVUHGQMDOLQLMDYDOMDLQVWRåFDSRY]HWDVUHGQMDSRYUãLQDORNDOQDYHOLNRVW
SRY]HWH]QDþLOQRVWL ,62 '$0
Geometrical Product Specifications (GPS) - Geometrical features - Part 2: Extracted
median line of a cylinder and a cone, extracted median surface, local size of an extracted
feature (ISO 14660-2:1999/DAM 1:2010)
Geometrische Produktspezifikation (GPS) - Geometrieelemente - Teil 2: Erfasste mittlere
Linie eines Zylinders und eines Kegels, erfasste mittlere Fläche, örtliches Maß eines
erfassten Geometrieelementes (ISO 14660-2:1999/DAM 1:2010)
Spécification géométrique des produits (GPS) - Éléments géométriques - Partie 2: Ligne
médiane extraite d'un cylindre et d'un cône, surface médiane extraite, taille locale d'un
élément extrait (ISO 14660-2:1999/DAM 1:2010)
Ta slovenski standard je istoveten z: EN ISO 14660-2:1999/prA1
ICS:
01.040.07 Matematika. Naravoslovne Mathematics. Natural
vede (Slovarji) sciences (Vocabularies)
17.040.01 Linearne in kotne meritve na Linear and angular
splošno measurements in general
SIST EN ISO 14660-2:2002/oprA1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14660-2:2002/oprA1:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 14660-2:2002/oprA1:2010
EUROPEAN STANDARD
DRAFT
EN ISO 14660-2:1999
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2010
ICS 01.100.20; 17.040.01
English Version
Geometrical Product Specifications (GPS) - Geometrical
features - Part 2: Extracted median line of a cylinder and a cone,
extracted median surface, local size of an extracted feature (ISO
14660-2:1999/DAM 1:2010)
Spécification géométrique des produits (GPS) - Éléments Geometrische Produktspezifikation (GPS) -
géométriques - Partie 2: Ligne médiane extraite d'un Geometrieelemente - Teil 2: Erfasste mittlere Linie eines
cylindre et d'un cône, surface médiane extraite, taille locale Zylinders und eines Kegels, erfasste mittlere Fläche,
d'un élément extrait (ISO 14660-2:1999/DAM 1:2010) örtliches Maß eines erfassten Geometrieelementes (ISO
14660-2:1999/DAM 1:2010)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 290.
This draft amendment A1, if approved, will modify the European Standard EN ISO 14660-2:1999. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14660-2:1999/prA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14660-2:2002/oprA1:2010
EN ISO 14660-2:1999/prA1:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14660-2:2002/oprA1:2010
EN ISO 14660-2:1999/prA1:2010 (E)
Foreword
This document (EN ISO 14660-2:1999/prA1:2010) has been prepared by Technical Committee ISO/TC 213
“Dimensional and geometrical product specifications and verification” in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.