prEN ISO 15614-4
(Main)Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 4: Finishing welding of aluminium castings (ISO/DIS 15614-4:2021)
Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 4: Finishing welding of aluminium castings (ISO/DIS 15614-4:2021)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe - Schweißverfahrensprüfung - Teil 4: Fertigungsschweißen von Aluminiumguss (ISO/DIS 15614-4:2021)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Épreuve de qualification d'un mode opératoire de soudage - Partie 4: Réparation par soudage pour les travaux de finition des pièces moulées en aluminium (ISO/DIS 15614-4:2021)
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Preskus varilnega postopka - 4. del: Varjenje aluminijevih ulitkov (ISO/DIS 15614-4:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2021
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Preskus varilnega
postopka - 4. del: Varjenje aluminijevih ulitkov (ISO/DIS 15614-4:2021)
Specification and qualification of welding procedures for metallic materials - Welding
procedure test - Part 4: Finishing welding of aluminium castings (ISO/DIS 15614-4:2021)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Schweißverfahrensprüfung - Teil 4: Fertigungsschweißen von Aluminiumguss (ISO/DIS
15614-4:2021)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Épreuve de qualification d'un mode opératoire de soudage - Partie 4:
Réparation par soudage pour les travaux de finition des pièces moulées en aluminium
(ISO/DIS 15614-4:2021)
Ta slovenski standard je istoveten z: prEN ISO 15614-4
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 15614-4
ISO/TC 44/SC 10 Secretariat: DIN
Voting begins on: Voting terminates on:
2021-09-07 2021-11-30
Specification and qualification of welding procedures for
metallic materials — Welding procedure test —
Part 4:
Finishing welding of aluminium castings
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Épreuve de
qualification d'un mode opératoire de soudage —
Partie 4: Réparation par soudage pour les travaux de finition des pièces moulées en aluminium
ICS: 25.160.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 15614-4:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021
ISO/DIS 15614-4:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
ISO/DIS 15614-4:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions .2
4 Preliminary welding procedure specification (pWPS) .2
5 Welding procedure test . 3
6 Test pieces . 3
6.1 General . 3
6.2 Shape and dimensions of test pieces . 3
6.3 Welding of test pieces . 4
7 Examination and testing . 5
7.1 Extent of testing . 5
7.2 Non-destructive testing . 6
7.3 Destructive testing . 6
7.3.1 Fracture testing . 6
7.3.2 Microscopic examination . 9
7.4 Acceptance levels . 9
7.5 Re-testing . 9
8 Range of qualification .10
8.1 General .10
8.2 Related to the manufacturer .10
8.3 Related to the parent material .10
8.3.1 Parent material grouping .10
8.3.2 Parent material thickness .10
8.4 Common to all welding procedures .10
8.5 Specific to processes .10
9 Welding procedure qualification record (WPQR) .10
Annex A (informative) Example of a welding procedure qualification record (WPQR) form .12
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/68/EU (PED) aimed to be covered .15
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/29/EU (SPVD) aimed to be covered .16
Bibliography .17
ISO/DIS 15614-4:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 10, Quality management in the field of welding.
Any feedback, question or request for official interpretation related to any aspect of this document
should be directed to the Secretariat of ISO/TC 44/SC 10 via your national standards body. A complete
listing of these bodies can be found at www .iso .org/ members .html.
Official interpretations of ISO/TC 44 documents, where they exist, are available from this page: https://
committee .iso .org/ sites/ tc44/ home/ interpretation .html.
This second edition cancels and replaces the first edition (ISO 15614-4:2005), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— normative references have been updated;
— to be updated closer to publication.
iv © ISO 2021 – All rights reserved
DRAFT INTERNATIONAL STANDARD ISO/DIS 15614-4:2021(E)
Specification and qualification of welding procedures for
metallic materials — Welding procedure test —
Part 4:
Finishing welding of aluminium castings
1 Scope
This document is part of a series of standards, details of which are given in ISO 15607:2019, Annex A.
This document specifies how a welding procedure specification for finishing welding of aluminium
castings is qualified by welding procedure tests.
Arc welding of aluminium castings is performed by the following processes in accordance with
ISO 4063:
— 131 MIG welding with solid wire electrode
— 132 MIG welding with flux cored electrode
— 133 MIG welding with metal cored electrode
— 141 TIG welding with solid filler material (wire/rod)
— 142 Autogenous TIG welding
— 143 TIG welding with tubular cored filler material (wire/rod)
— 145 TIG welding using reducing gas and solid filler material (wire/rod)
— 146 TIG welding using reducing gas and tubular cored filler material (wire/rod)
— 15 plasma arc welding
The shielding gases used with these processes are:
— argon, ISO 14175 – I1
— helium, ISO 14175 – I2
— argon helium mixture, ISO 14175 – I3
The principles of this document can be applied to other welding processes and shielding gases.
This document is not applicable for repair welding or for welding of joints where ISO 15614-2 is to be
used.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3452-1, Non-destructive testing — Penetrant testing — Part 1: General principles
ISO 4063, Welding and allied processes — Nomenclature of processes and reference numbers
ISO/DIS 15614-4:2021(E)
ISO 6947, Welding and allied processes — Welding positions
ISO 9017, Destructive tests on welds in metallic materials — Fracture test
ISO 10042, Welding — Arc-welded joints in aluminium and its alloys — Quality levels for imperfections
ISO 14175, Welding consumables
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.