CEN ISO/TS 15877-7:2009
(Main)Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2009)
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2009)
ISO 15877-7:2009 gives guidance for the assessment of conformity included in the manufacturer's quality plan as part of his/her quality system.
ISO 15877-7:2009 includes:
- provisions for materials, components, joints and assemblies given in the applicable part(s) of ISO 15877;
- provisions for the manufacturer's quality system, which can conform to ISO 9001;
- definitions and procedures applied if certification is involved; in which case, the certification body can be accredited to ISO/IEC Guide 65 or ISO/IEC Guide 62, as applicable.
In conjunction with the other parts of ISO 15877, ISO 15877-7:2009 is applicable to chlorinated poly(vinyl chloride) (PVC-C) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems), under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 15877-1:2009).
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes Polyvinylchlorid (PVC-C) - Teil 7: Empfehlungen für die Beurteilung der Konformität (ISO/TS 15877-7:2009)
Diese Technische Spezifikation gibt Empfehlungen für die Beurteilung der Konformität im Rahmen des Qualitätssicherungsplans
des Herstellers als Teil von dessen Qualitätssicherungssystem.
Diese Technische Spezifikation enthält:
a) Festlegungen für Werkstoffe, Rohrleitungsteile sowie Verbindungen und Bauteilkombinationen, die im
betreffenden Teil der ISO 15877 festgelegt sind;
b) Festlegungen für das Qualitätssicherungssystem des Herstellers, das ISO 9001 [2] entsprechen kann;
c) Definitionen und Verfahren bei einer Zertifizierung; in diesem Fall kann die Zertifizierungsstelle in
Abhängigkeit der Anwendung nach ISO/IEC Guide 65 [5] oder ISO/IEC Guide 62 [4] akkreditiert sein.
Zusammen mit den übrigen Teilen der ISO 15877 gilt diese Technische Spezifikation für Rohrleitungssysteme
aus chloriertem Polyvinylchlorid (PVC-C), die in der Warm- und Kaltwasserinstallation innerhalb von
Gebäuden für den Transport von Trink- oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen
unter Berücksichtigung des betreffenden zulässigen Betriebsdruckes und der für die jeweilige Anwendungsklasse
geltenden Temperaturen (siehe ISO 15877-1:2009, Tabelle 1) eingesetzt werden.
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Poly(chlorure de vinyle) chloré (PVC-C) - Partie 7: Guide pour l'évaluation de la conformité (ISO/TS 15877-7:2009)
L'ISO 15877-7:2009 est un guide pour l'évaluation de la conformité, inclus dans le plan qualité du fabricant dans le cadre de son système qualité.
L'ISO 15877-7:2009 comporte ceci:
– les exigences relatives aux matières, aux composants, aux assemblages et aux montages, énoncées dans la ou les parties applicables de l'ISO 15877;
– les exigences relatives au système qualité du fabricant, qui peut être conforme à l'ISO 9001;
– les définitions et procédures appliquées en cas de certification par tierce partie; en ce cas-là, l'organisme de certification peut être accrédité suivant l'ISO/CEI Guide 65 ou l'ISO/CEI Guide 62, selon le guide approprié.
Conjointement avec les autres parties de l'ISO 15877, l'ISO 15877-7:2009 est applicable aux systèmes de canalisations en poly(chlorure de vinyle) chloré (PVC-C) destinés aux installations d'eau chaude et froide pour le transport de l'eau dans les bâtiments, que l'eau soit ou non destinée à la consommation humaine (systèmes domestiques), à des pressions et des températures de calcul correspondant à la classe d'application (voir le Tableau 1 de l'ISO 15877-1:2009).
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Klorirani polivinilklorid (PVC-C) - 7. del: Navodilo za ugotavljanje skladnosti (ISO/TS 15877-7:2009)
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2009
1DGRPHãþD
SIST-TS CEN ISO/TS 15877-7:2004
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
.ORULUDQLSROLYLQLONORULG 39&& GHO 1DYRGLOR]DXJRWDYOMDQMHVNODGQRVWL
,6276
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl
chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-
7:2009)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Chloriertes
Polyvinylchlorid (PVC-C) - Teil 7: Empfehlungen für die Beurteilung der Konformität
(ISO/TS 15877-7:2009)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Poly(chlorure de vinyle) chloré (PVC-C) - Partie 7: Guide pour l'évaluation de la
conformité (ISO/TS 15877-7:2009)
Ta slovenski standard je istoveten z: CEN ISO/TS 15877-7:2009
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL SPECIFICATION
CEN ISO/TS 15877-7
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
September 2009
ICS 23.040.01; 23.040.20; 91.140.60 Supersedes CEN ISO/TS 15877-7:2003
English Version
Plastics piping systems for hot and cold water installations -
Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for
the assessment of conformity (ISO/TS 15877-7:2009)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Poly(chlorure de Kaltwasserinstallation - Chloriertes Polyvinylchlorid (PVC-
vinyle) chloré (PVC-C) - Partie 7: Guide pour l'évaluation de C) - Teil 7: Empfehlungen für die Beurteilung der
la conformité (ISO/TS 15877-7:2009) Konformität (ISO/TS 15877-7:2009)
This Technical Specification (CEN/TS) was approved by CEN on 22 August 2009 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 15877-7:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (CEN ISO/TS 15877-7:2009) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems", the secretariat of which is held by NEN, in collaboration with
Technical Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids".
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 15877-7:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
TECHNICAL ISO/TS
SPECIFICATION 15877-7
Second edition
2009-09-15
Plastics piping systems for hot and cold
water installations — Chlorinated
poly(vinyl chloride) (PVC-C) —
Part 7:
Guidance for the assessment of
conformity
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Poly(chlorure de vinyle) chloré (PVC-C) —
Partie 7: Guide pour l'évaluation de la conformité
Reference number
ISO/TS 15877-7:2009(E)
©
ISO 2009
ISO/TS 15877-7:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
ISO/TS 15877-7:2009(E)
Contents Page
Foreword. iv
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 2
3.1 Terms and definitions. 2
3.2 Abbreviated terms . 4
4 Requirements . 5
4.1 General. 5
4.2 Testing and inspection. 5
Bibliography . 13
ISO/TS 15877-7:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of document:
— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
— an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 15877-7 was prepared by European Committee for Standardization (CEN) Technical Committee
CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical Committee
ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes
and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This Technical Specification is part of a System Standard for plastics piping systems of a particular material
for a specified application. There are a number of such System Standards.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
They are supported by separate standards on test methods to which references are made throughout the
System Standard.
This second edition cancels and replaces the first edition (ISO/TS 15877-7:2003), which has been technically
revised.
iv © ISO 2009 – All rights reserved
ISO/TS 15877-7:2009(E)
1)
ISO 15877 consists of the following parts , under the general title Plastics piping systems for hot and cold
water installations — Chlorinated poly(vinyl chloride) (PVC-C):
⎯ Part 1: General
⎯ Part 2: Pipes
⎯ Part 3: Fittings
⎯ Part 5: Fitness for purpose of the system
⎯ Part 7: Guidance for the assessment of conformity [Technical Specification]
This Technical Specification can be used to support elaboration of national certification procedures for
products conforming to the applicable part(s) of ISO 15877.
At the date of publication of this Technical Specification, System Standards for piping systems of other
plastics materials used for hot and cold water installations are the following:
ISO 15874 (all parts), Plastics piping systems for hot and cold water installations — Polypropylene (PP)
ISO 15875 (all parts), Plastics piping systems for hot and cold water installations — Crosslinked polyethylene
(PE-X)
ISO 15876 (all parts), Plastics piping systems for hot and cold water installations — Polybutylene (PB)
2)
ISO 22391:— (all parts), Plastics piping systems for hot and cold water installations — Polyethylene of
raised temperature resistance (PE-RT)
1) This System Standard does not incorporate a part 4: Ancillary equipment or a part 6: Guidance for installation. For
ancillary equipment, separate standards can apply. Guidance for installation of plastics piping systems made from different
[6]
materials, intended to be used for hot and cold water installations, is covered by ENV 12108 .
2) To be published. (Revisions of ISO 22391-1:2007, ISO 22391-2:2007, ISO 22391-3:2007, ISO 22391-5:2007)
ISO/TS 15877-7:2009(E)
Introduction
This Technical Specification is a part of the System Standard which specifies the requirements for a piping
system when made from chlorinated poly(vinyl chloride) (PVC-C). The piping system is intended to be used
for hot and cold water installations and heating system installations.
In respect of potential adverse effects on the quality of water intended for hum
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.