EN ISO 26945:2011
(Main)Metallic and other inorganic coatings - Electrodeposited coatings of tin-cobalt alloy (ISO 26945:2011)
Metallic and other inorganic coatings - Electrodeposited coatings of tin-cobalt alloy (ISO 26945:2011)
ISO 26945:2011 specifies electrodeposited coatings of tin-cobalt alloy of approximate composition 75 % (mass fraction) to 80 % (mass fraction) tin, remainder cobalt, as a substitute for decorative chromium coatings of 0,1 µm to 0,3 µm thickness. Hardness and wear resistance properties of the coatings obtained are not equivalent to those of chromium coatings, but similar to those of tin-nickel alloy coatings.
Tin-cobalt alloy coatings can be applied by rack or barrel plating processes.
ISO 26945:2011 does not specify requirements for the surface condition of the basis metal prior to electroplating.
Metallische und andere anorganische Überzüge - Galvanische Überzüge aus Zinn-Cobalt-Legierungen (ISO 26945:2011)
Diese Internationale Norm legt galvanische Überzüge aus Zinn-Cobalt-Legierungen mit einer Zusammensetzung
von etwa 75 % (Massenanteil) bis 80 % (Massenanteil) Zinn, Rest Cobalt, als möglichen Ersatz für
dekorative Chromüberzüge mit einer Dicke des Überzugs von 0,1 μm bis 0,3 μm fest. Härte und Verschleißwiderstand
von Zinn-Cobalt-Überzügen entsprechen nicht den Eigenschaften von Chromüberzügen, sind aber
vergleichbar mit denen von Zinn-Nickel-Legierungsüberzügen.
Zinn-Cobalt-Legierungsüberzüge können auf Trommel- oder Gestellware aufgebracht werden.
Diese Internationale Norm stellt keine Anforderungen an den Oberflächenzustand des Grundmetalls vor der
galvanischen Metallabscheidung.
Revêtements métalliques et autres revêtements inorganiques - Dépôts électrolytiques d'alliage étain-cobalt (ISO 26945:2011)
L'ISO 26945:2011 spécifie des revêtements électrolytiques d'alliage étain-cobalt dont la composition est approximativement de 75 % (fraction massique) à 80 % (fraction massique) d'étain et le reste de cobalt, pouvant remplacer des dépôts de chrome décoratifs de 0,1 μm à 0,3 µm d'épaisseur. Les propriétés de dureté et de résistance à l'usure des revêtements d'alliage étain-cobalt ne sont pas équivalentes à celles des dépôts de chrome mais elles sont similaires à celles des dépôts d'alliage étain-nickel.
Les revêtements d'alliage étain-cobalt peuvent être appliqués par la technique de dépôt à l'attache et au tonneau.
L'ISO 26945:2011 ne spécifie aucune exigence concernant l'état de surface du métal de base avant dépôt électrolytique.
Kovinske in druge anorganske prevleke - Galvanske prevleke kositer-kobaltovih zlitin (ISO 26945:2011)
Ta mednarodni standard določa galvanske prevleke kositer-kobaltovih zlitin s približno sestavo 75 % (masnega deleža) do 80 % (masnega deleža) kositra, preostanek je kobalt, kot nadomestek za okrasne kromove prevleke z debelino 0,1 μm do 0,3 μm. Dobljena trdota in odpornost prevlek proti obrabi nista enakovredni trdoti in odpornosti kromovih prevlek, podobni pa sta trdoti in odpornosti prevlek iz kositer-nikljevih zlitin. Prevleke iz kositer-kobaltovih zlitin se lahko nanašajo z galvanizacijo z obešanjem ali v galvanskih bobnih. Ta mednarodni standard ne določa zahtev za stanje površine osnovne kovine pred galvanizacijo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2011
1DGRPHãþD
SIST EN ISO 26945:2009
Kovinske in druge anorganske prevleke - Galvanske prevleke kositer-kobaltovih
zlitin (ISO 26945:2011)
Metallic and other inorganic coatings - Electrodeposited coatings of tin-cobalt alloy (ISO
26945:2011)
Metallische und andere anorganische Überzüge - Galvanische Überzüge aus Zinn-
Cobalt-Legierungen (ISO 26945:2011)
Revêtements métalliques et autres revêtements inorganiques - Dépôts électrolytiques
d'alliage étain-cobalt (ISO 26945:2011)
Ta slovenski standard je istoveten z: EN ISO 26945:2011
ICS:
25.220.40 Kovinske prevleke Metallic coatings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 26945
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2011
ICS 25.220.40 Supersedes EN ISO 26945:2008
English Version
Metallic and other inorganic coatings - Electrodeposited coatings
of tin-cobalt alloy (ISO 26945:2011)
Revêtements métalliques et autres revêtements Metallische und andere anorganische Überzüge -
inorganiques - Dépôts électrolytiques d'alliage étain-cobalt Galvanische Überzüge aus Zinn-Cobalt-Legierungen (ISO
(ISO 26945:2011) 26945:2011)
This European Standard was approved by CEN on 8 February 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 26945:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 26945:2011) has been prepared by Technical Committee ISO/TC 107 "Metallic and
other inorganic coatings" in collaboration with Technical Committee CEN/TC 262 “Metallic and other inorganic
coatings” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2011, and conflicting national standards shall be withdrawn at
the latest by August 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 26945:2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 26945:2011 has been approved by CEN as a EN ISO 26945:2011 without any modification.
INTERNATIONAL ISO
STANDARD 26945
Second edition
2011-02-15
Metallic and other inorganic coatings —
Electrodeposited coatings of tin-cobalt
alloy
Revêtements métalliques et autres revêtements inorganiques — Dépôts
électrolytiques d'alliage étain-cobalt
Reference number
ISO 26945:2011(E)
©
ISO 2011
ISO 26945:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 26945:2011(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Essential information to be supplied by the purchaser to the processor.2
5 Designation .3
5.1 General .3
5.2 Designation specification.3
5.3 Basis metal.3
5.4 Designation of heat treatment requirements.4
5.5 Examples.4
6 Requirements.4
6.1 Basis material .4
6.2 Appearance .5
6.3 Undercoats.5
6.4 Thickness .5
6.5 Adhesion .6
6.6 Quality-evaluation test of tin-cobalt alloy coatings .6
6.7 Stress-relief heat treatment prior to electroplating .7
6.8 Hydrogen-embrittlement-relief heat treatment after electroplating .7
7 Sampling .7
Annex A (normative) Methods of measuring the thickness of tin-cobalt alloy coatings .8
Bibliography.10
ISO 26945:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 26945 was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings.
This second edition cancels and replaces the first edition (ISO 26945:2008), of which it constitutes a minor
revision.
iv © ISO 2011 – All rights reserved
ISO 26945:2011(E)
Introduction
Electrodeposited coating of tin-cobalt alloy is characterized by its bright surface which is similar to decorative
chromium coating. Hardness and wear-resistance properties of tin-cobalt alloy coatings are not equivalent to
those of chromium coatings, but are similar to those of tin-nickel alloy coatings (see ISO 2179). Thus,
tin-cobalt coatings may be regarded, as far as surface lustre is concerned, as one of the possible alternatives
to chromium coating. Due to its higher current efficiency (more than 70 %), tin-cobalt alloy coatings can be
applied by rack-and-barrel plating processes to a wide range of complicated shapes and sizes, e.g. nuts, bolts,
rivets, etc.
INTERNATIONAL STANDARD ISO 26945:2011(E)
Metallic and other inorganic coatings — Electrodeposited
coatings of tin-cobalt alloy
WARNING — This International Standard may not be compliant with some countries' health and safety
legislations and calls for the use of substances and/or procedures that may be injurious to health if
adequate safety measures are not taken. This International Standard does not address any health
hazards, safety or environmental matters and legislations associated with its use. It is the
responsibility of the user of this International Standard to establish appropriate health, safety and
environmentally acceptable practices and take suitable actions to comply with any national and
international regulations. Compliance with this International Standard does not in itself confer
immunity from legal obligations.
1 Scope
This International Standard specifies electrodeposited coatings of tin-cobalt alloy of approximate composition
75 % (mass fraction) to 80 % (mass fraction) tin, remainder cobalt, as a substitute for decorative chromium
coatings of 0,1 µm to 0,3 µm thickness. Hardness and wear resistance properties of the coatings obtained are
not equivalent to those of chromium coatings, but similar to those of tin-nickel alloy coatings.
Tin-cobalt alloy coatings can be applied by rack or barrel plating processes.
This International Standard does not specify requirements for the surface condition of the basis metal prior to
electroplating.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1463, Metallic and oxide coatings — Measurement of coating thickness — Microscop
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.