EN ISO 16000-7:2007
(Main)Indoor air - Part 7: Sampling strategy for determination of airborne asbestos fibre concentrations (ISO 16000-7:2007)
Indoor air - Part 7: Sampling strategy for determination of airborne asbestos fibre concentrations (ISO 16000-7:2007)
ISO 16000-7:2007 specifies procedures to be used in planning of air measurements to determine the concentrations of asbestos in indoor atmospheres. Careful planning of the measurement strategy is important, because the results can become the basis of recommendations for major building renovations, or for the return of a building to normal occupancy status after removal of asbestos-containing materials.
ISO 16000-7:2007 uses the following definition for indoor environments as specified in ISO 16000-1: dwellings having living rooms, bedrooms, do-it-yourself (DIY) rooms, recreation rooms, cellars, kitchens and bathrooms; workrooms or workplaces in buildings which are not subject to health and safety inspections in regard to air pollutants (for example, offices and sales premises); public and commercial buildings (for example, hospitals, schools, kindergartens, sports halls, libraries, restaurants and bars, theatres and other function rooms); cabins of vehicles and public transport.
Innenraumluftverunreinigungen - Teil 7: Probenahmestrategie zur Bestimmung luftgetragener Asbestfaserkonzentrationen (ISO 16000-7:2007)
In diesem Teil der ISO 16000 werden Verfahren festgelegt, die bei der Planung von Luftuntersuchungen zur Bestimmung der Asbestkonzentrationen im Innenraum verwendet werden. Die sorgfältige Planung der Messstrategie ist sehr wichtig, weil die Ergebnisse als Basis für die Empfehlungen für größere Gebäudesanierungen dienen oder für die Wiedereinstufung des Gebäudes in den Benutzbarkeitsstatus nach der Entfernung asbesthaltiger Materialien verwendet werden.
In diesem Teil der EN ISO 16000 wird die folgende Definition, so wie die in ISO 16000-1 festgelegt ist, für den Innenraum verwendet:
Wohnungen mit Wohn , Schlaf , Bastel , Sport , Kellerräumen, Küchen und Badezimmern;
Arbeitsräume bzw. Arbeitsplätze in Gebäuden, die nicht im Hinblick auf Luftschadstoffe arbeitsschutz-rechtlichen Kontrollen unterliegen (so z. B. Büros und Verkaufsräume);
öffentliche und kommerzielle Gebäude (z. B. Krankenhäuser, Altersheime, Schulen, Kindergärten, Sporthallen, Bibliotheken, Restaurants und Gaststätten, Theater und andere Veranstaltungsräume);
Fahrgasträume von Kraftfahrzeugen und öffentliche Verkehrsmittel.
Air intérieur - Partie 7: Stratégie d'échantillonnage pour la détermination des concentrations en fibres d'amiante en suspension dans l'air (ISO 16000-7:2007)
L'ISO 16000-7:2007 spécifie les modes opératoires à employer dans la planification des mesurages de l'air pour la détermination des concentrations en amiante des atmosphères intérieures. Il est important de planifier attentivement la stratégie de mesurage car les résultats peuvent constituer la base de recommandations visant les rénovations majeures d'un bâtiment ou le retour à la normale de l'occupation d'un bâtiment après retrait des matériaux contenant de l'amiante.
L'ISO 16000-7:2007 utilise la définition des environnements intérieurs telle que spécifiée dans l'ISO 16000-1: habitations possédant des séjours, des chambres à coucher, des pièces pour le bricolage, des salles de jeu, des caves, des cuisines et des salles de bain; pièces ou lieux de travail au sein des bâtiments non soumis aux inspections d'hygiène et sécurité concernant les polluants de l'air intérieur (par exemple, bureaux, locaux commerciaux); bâtiments publics ou commerciaux (par exemple hôpitaux, écoles, jardins d'enfants, salles de sport, bibliothèques, restaurants et bars, théâtres et autres salles); habitacles des véhicules et des transports en commun.
Notranji zrak - 7. del: Strategija vzorčenja za določevanje koncentracij azbestnih vlaken v zraku (ISO 16000-7:2007)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2008
1RWUDQML]UDNGHO 6WUDWHJLMDY]RUþHQMD]DGRORþHYDQMHNRQFHQWUDFLMD]EHVWQLK
YODNHQY]UDNX ,62
Indoor air - Part 7: Sampling strategy for determination of airborne asbestos fibre
concentrations (ISO 16000-7:2007)
Innenraumluftverunreinigungen - Teil 7: Probenahmestrategie zur Bestimmung
luftgetragener Asbestfaserkonzentrationen (ISO 16000-7:2007)
Air intérieur - Partie 7: Stratégie d'échantillonnage pour la détermination des
concentrations en fibres d'amiante en suspension dans l'air (ISO 16000-7:2007)
Ta slovenski standard je istoveten z: EN ISO 16000-7:2007
ICS:
13.040.20
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 16000-7
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2007
ICS 13.040.20
English Version
Indoor air - Part 7: Sampling strategy for determination of
airborne asbestos fibre concentrations (ISO 16000-7:2007)
Air intérieur - Partie 7: Stratégie d'échantillonnage pour la Innenraumluftverunreinigungen - Teil 7:
détermination des concentrations en fibres d'amiante en Probenahmestrategie zur Bestimmung luftgetragener
suspension dans l'air (ISO 16000-7:2007) Asbestfaserkonzentrationen (ISO 16000-7:2007)
This European Standard was approved by CEN on 13 July 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16000-7:2007: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Foreword
This document (EN ISO 16000-7:2007) has been prepared by Technical Committee ISO/TC 146 "Air quality"
in collaboration with Technical Committee CEN/TC 264 “Air quality” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2008, and conflicting national standards shall be withdrawn
at the latest by February 2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 16000-7:2007 has been approved by CEN as a EN ISO 16000-7:2007 without any
modification.
INTERNATIONAL ISO
STANDARD 16000-7
First edition
2007-08-01
Indoor air —
Part 7:
Sampling strategy for determination of
airborne asbestos fibre concentrations
Air intérieur —
Partie 7: Stratégie d'échantillonnage pour la détermination
des concentrations en fibres d'amiante en suspension dans l'air
Reference number
ISO 16000-7:2007(E)
©
ISO 2007
ISO 16000-7:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 16000-7:2007(E)
Contents Page
Foreword. iv
Introduction . vi
1 Scope. 1
2 Normative references. 1
3 Sources and occurrence. 1
4 Terms and definitions. 2
5 Symbols and abbreviations . 6
6 Measurement strategy. 7
7 Quality assurance. 19
Annex A (normative) Simulation methods. 21
Annex B (informative) Choice of analytical method . 23
Annex C (informative) Example of sample data form . 25
Annex D (informative) Example of summary report form . 26
Bibliography . 28
ISO 16000-7:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take Part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16000-7 was prepared by Technical Committee ISO/TC 146, Air quality, Subcommittee SC 6, Indoor air.
ISO 16000 consists of the following parts, under the general title Indoor air :
⎯ Part 1: General aspects of sampling strategy
⎯ Part 2: Sampling strategy for formaldehyde
⎯ Part 3: Determination of formaldehyde and other carbonyl compounds — Active sampling method
⎯ Part 4: Determination of formaldehyde — Diffusive sampling method
⎯ Part 5: Sampling strategy for volatile organic compounds (VOCs)
⎯ Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on ®
Tenax TA sorbent, thermal desorption and gas-chromatography using MS/FID
⎯ Part 7: Sampling strategy for determination of airborne asbestos fibre concentrations
⎯ Part 8: Determination of local mean ages of air in buildings for characterizing ventilation conditions
⎯ Part 9: Determination of the emission of volatile organic compounds from building products and furnishing —
Emission test chamber method
⎯ Part 10: Determination of the emission of volatile organic compounds from building products and
furnishing — Emission test cell method
⎯ Part 11: Determination of the emission of volatile organic compounds from building products and
furnishing —Sampling, storage of samples and preparation of test specimens
⎯ Part 12: Sampling strategy for polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins
(PCDDs), polychlorinated dibenzofurans (PCDFs) and polycyclic aromatic hydrocarbons (PAHs)
⎯ Part 13: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs) and
polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/PCDFs) — Collection on sorbent-backed filters
iv © ISO 2007 – All rights reserved
ISO 16000-7:2007(E)
⎯ Part 14: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs) and
polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/PCDFs) — Extraction, clean-up and analysis by
high-resolution gas chromatography/mass spectrometry
⎯ Part 15: Sampling strategy for nitrogen dioxide (NO )
⎯ Part 16: Detection and enumeration of moulds — Sampling by filtration
⎯ Part 17: Detection and enumeration of moulds — Culture-based method
The following parts are under preparation:
⎯ Part 18: Detection and enumeration of moulds — Sampling by impaction
⎯ Part 23: Performance test for evaluating the reduction of formaldehyde concentrations by sorptive
building materials
⎯ Part 24: Performance test for evaluating the concentration reduction of volatile organic compounds and
carbonyl compounds except formaldehyde by sorptive building materials
⎯ Part 25: Determination of the emission of semi volatile organic compounds for building products — Micro
chamber method
The following parts are planned:
⎯ Part 19: Sampling strategy for moulds
⎯ Part 20: Detection and enumeration of moulds — Sampling from house dust
⎯ Part 21: Detection and enumeration of moulds — Sampling from materials
⎯ Part 22: Detection and enumeration of moulds — Molecular methods
⎯ Part 26: Road vehicle interior test stand — Determination of VOC, SVOC and carbonyls including
formaldehyde in car interiors
Furthermore, two International Standards, ISO 16017-1 on pumped sampling and ISO 16017-2 on diffusive
sampling, focus on volatile organic compound (VOC) measurements.
ISO 16000-7:2007(E)
Introduction
Measurements of airborne asbestos fibre concentrations in indoor atmospheres are made for several reasons
related to short-term or long-term exposure of building occupants to asbestos. One application of such
measurements is to ensure that airborne asbestos fibres dispersed in areas of a building that are undergoing
asbestos abatement do not result in unacceptable exposures of occupants in other areas of the building. After
asbestos abatement is completed, measurements are made prior to removal of containment barriers and
before safety precautions are discontinued to determine whether any residual asbestos that may remain in the
abated area could give rise to unacceptable airborne asbestos exposures when the areas are re-occupied.
The characterization and assessment of ambient air at a fixed position, whether in a building or outside, is
normally based on a series of measurements made over a long period of time, generally months or years.
However, the release of asbestos fibres into ambient air is not constant and human, or in some cases animal,
activity will result in short-term release episodes. Maintenance activity in particular will disturb asbestos-
containing materials and settled dust in buildings. Control and monitoring of these activities will determine the
[1][2]
long-term exposure levels . Workplace atmospheres are also assessed by a series of repeated
measurements, the number of measurements depending on the difference between the measured value and
the control limit.
In contrast to the strategy used for assessment of long-term asbestos fibre concentrations and personal
exposure
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.