EN ISO 11298-3:2018

Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2018)

This document, in conjunction with ISO 11298‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe.
It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE       For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.

Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten Wasserversorgungsnetzen - Teil 3: Close-Fit-Lining (ISO 11298-3:2018)

Systèmes de canalisations en plastique pour la rénovation des réseaux enterrés d'alimentation en eau - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11298-3:2018)

Le présent document, conjointement à l'ISO 11298‑1, spécifie les exigences et les méthodes d'essai pour les systèmes de tubage par tuyau continu sans espace annulaire utilisés pour la rénovation des réseaux d'alimentation en eau, qui transportent de l'eau destiné à la consommation humaine, y compris les canalisations pour la prise d'eau brute.
Il s'applique aux tuyaux et raccords, tels que fabriqués, ainsi qu'au système de rénovation installé. Il s'applique aux tuyaux en polyéthylène (PE) ayant soit une construction monocouche à paroi compacte soit une construction à couches coextrudées, laquelle est réduite en usine ou sur site pour fournir un tubage autostructurant et un tubage nécessitant le maintien de l'enveloppe sans espace annulaire, ainsi qu'aux raccords associés et aux assemblages pour la construction du système de rénovation. Il ne s'applique pas aux tuyaux revêtus de PE comportant une couche thermoplastique supplémentaire pelable et contiguë à l'extérieur du tuyau.
Il s'applique aux tuyaux, raccords et montages en PE destinés à être utilisés à une température de fonctionnement de 20 °C, qui est la température de référence.
NOTE       Pour les applications à des températures constantes comprises entre 20 °C et 40 °C, voir l'ISO 4427‑1:2007, Annexe A.

Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z vodo - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11298-3:2018)

Ta dokument v povezavi s standardom ISO 11298-1 določa zahteve in preskusne metode za tesno prilagodljive sisteme cevi, ki se uporabljajo za obnovo podzemnih omrežij za oskrbo z vodo, po katerih se pretaka pitna voda, vključno s cevmi za dovajanje neobdelane vode.
Uporablja se za cevi in fitinge, kot so izdelani, ter za nameščene sisteme cevi. Uporablja se za polietilenske (PE) cevi s trdno steno iz ene plasti ali s konstrukcijo koekstrudiranih slojev, ki se v tovarni ali na mestu uporabe zmanjša, da se zagotovi tesno prilegajoča se neodvisna ali interaktivna obloga cevi pod tlakom, ter tudi za povezane fitinge in spoje za konstrukcijo sistema cevi. Ne uporablja se za cevi, prevlečene s polietilenom, ki imajo na zunanji strani stični, termoplastični dodatni sloj, ki ga je mogoče odluščiti. Uporablja se za polietilenske cevi, fitinge in sestave, namenjene za uporabo pri delovni temperaturi 20 °C kot referenčni temperaturi. OPOMBA: V zvezi z napravami, ki delujejo pri stalnih temperaturah od 20 do 40 °C, glej dodatek A k standardu ISO 4427-1:2007.

General Information

• Status: Published
• Publication Date: 09-Oct-2018
• Withdrawal Date: 29-Apr-2019
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• ICS: 93.025 - External water conveyance systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 17 - Plastic components for the use of renovation of piping systems
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 10-Oct-2018
• Completion Date: 10-Oct-2018
• Ref Project: SIST EN ISO 11298-3:2018 - Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2018)

Relations

• Replaces: EN ISO 11298-3:2011 - Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2010)
• Effective Date: 17-Oct-2018

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 11298-3:2011
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z
vodo - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11298-3:2018)
Plastics piping systems for renovation of underground water supply networks - Part 3:
Lining with close-fit pipes (ISO 11298-3:2018)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten
Wasserversorgungsnetzen - Teil 3: Close-Fit-Lining (ISO 11298-3:2018)
Systèmes de canalisations en plastique pour la rénovation des réseaux enterrés
d'alimentation en eau - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO
11298-3:2018)
Ta slovenski standard je istoveten z: EN ISO 11298-3:2018
ICS:
23.040.03 Cevovodi za zunanje sisteme Pipeline and its parts for
transporta vode in njihovi deli external water conveyance
systems
93.025 Zunanji sistemi za prevajanje External water conveyance
vode systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11298-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 93.025 Supersedes EN ISO 11298-3:2011
English Version
Plastics piping systems for renovation of underground
water supply networks - Part 3: Lining with close-fit pipes
(ISO 11298-3:2018)
Systèmes de canalisations en plastique pour la Kunststoff-Rohrleitungssysteme für die Renovierung
rénovation des réseaux enterrés d'alimentation en eau von erdverlegten Wasserversorgungsnetzen - Teil 3:
- Partie 3: Tubage par tuyau continu sans espace Close-Fit-Lining (ISO 11298-3:2018)
annulaire (ISO 11298-3:2018)
This European Standard was approved by CEN on 19 August 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11298-3:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 11298-3:2018) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11298-3:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11298-3:2018 has been approved by CEN as EN ISO 11298-3:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 11298-3
Second edition
2018-09
Plastics piping systems for renovation
of underground water supply
networks —
Part 3:
Lining with close-fit pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux
enterrés d'alimentation en eau —
Partie 3: Tubage par tuyau continu sans espace annulaire
Reference number
ISO 11298-3:2018(E)
©
ISO 2018
ISO 11298-3:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 11298-3:2018(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 General . 2
3.2 Techniques . 2
3.3 Characteristics . 3
3.4 Materials . 3
3.5 Product stages . 3
3.6 Service conditions . 3
3.7 Joints . 4
4 Symbols and abbreviated terms . 4
4.1 Symbols . 4
4.2 Abbreviated terms . 5
5 Pipes at the “M” stage . 5
5.1 Materials . 5
5.1.1 Virgin material . 5
5.1.2 Reprocessable and recyclable material . 5
5.2 General characteristics . 5
5.2.1 Appearance . 5
5.2.2 Colour . 5
5.3 Material characteristics . 6
5.4 Geometric characteristics . 6
5.5 Mechanical characteristics. 6
5.6 Physical characteristics . 6
5.7 Jointing . 6
5.8 Marking . 6
5.9 Regional requirements for pipes . 7
6 Fittings at the “M” stage . 7
6.1 Requirements . 7
6.2 Marking . 7
6.3 Regional requirements for fittings . 7
7 Ancillary components . 7
8 Fitness for purpose of the installed lining system at the “I” stage .7
8.1 Materials . 7
8.2 General characteristics . 7
8.3 Material characteristics . 7
8.4 Geometric characteristics . 8
8.5 Mechanical characteristics. 8
8.6 Physical characteristics .
...