prEN ISO 2361

Electrodeposited nickel coatings on magnetic and non-magnetic substrates - Measurement of coating thickness - Magnetic method (ISO/DIS 2361:2024)

This second edition cancels and replaces the first edition (i. e. ISO 2361:1972). Specifies the method of using coating thickness instruments of the magnetic type ror non-destructive measurements of the thickness. The method may nkot be applicable to autocatalytic (electroless) nickel coatings. For the purpose of this Standasd, two types of nickel coating are disringuished: coatings on magnetic substrates and on non-magnetic substrates.

Elektrolytisch erzeugte Nickelschichten auf magnetischen und nichtmagnetischen Grundmetallen- Messen der Schichtdicke- Magnetverfahren (ISO/DIS 2361:2024)

Revêtements électrolytiques de nickel sur substrat magnétique et non magnétique - Mesurage de l’épaisseur du revêtement - Méthode magnétique (ISO/DIS 2361:2024)

La présente Norme internationale spécifie une méthode magnétique de mesurage non destructif de l'épaisseur des revêtements électrolytiques de nickel sur métal de base magnétique ou non magnétique. Cette méthode ne s'applique pas aux revêtements autocatalytiques de nickel (nickel chimique), du fait de leur composition chimique. La présente Norme internationale concerne deux types de dépôts de nickel, à savoir :
a) revêtements de nickel sur métal de base magnétique (revêtements de type A);
b) revêtements de nickel sur métal de base non-magnétique (revêtements de type B).
Tous les instruments peuvent être utilisés sur les deux types de revêtements. Les instruments basés sur le principe de l'attraction magnétique ont une plage de mesurage efficace allant jusqu'à 50 µm dans le cas de revêtements de type A, et allant jusqu'à 25 µm pour les revêtements de type B. Les instruments de mesurage par réluctance ont une plage de mesurage bien supérieure, permettant des mesurages jusqu’à 1 mm et plus sur les deux types de revêtements.

Galvansko nanašanje niklja na magnetne in nemagnetne podlage - Merjenje debeline prevleke - Magnetna metoda (ISO/DIS 2361:2024)

General Information

• Status: Not Published
• Publication Date: 08-Mar-2026
• ICS: 25.220.40 - Metallic coatings
• Technical Committee: CEN/TC 262 - Metallic and other inorganic coatings
• Current Stage: 4060 - Closure of enquiry - Enquiry
• Start Date: 06-Nov-2024
• Completion Date: 06-Nov-2024
• Ref Project: oSIST prEN ISO 2361:2024 - Electrodeposited nickel coatings on magnetic and non-magnetic substrates - Measurement of coating thickness - Magnetic method (ISO/DIS 2361:2024)

Relations

• Revises: EN ISO 2361:1995 - Electrodeposited nickel coatings on magnetic and non-magnetic substrates - Measurement of coating thickness - Magnetic method (ISO 2361:1982)
• Effective Date: 15-Nov-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2024
Galvansko nanašanje niklja na magnetne in nemagnetne podlage - Merjenje
debeline prevleke - Magnetna metoda (ISO/DIS 2361:2024)
Electrodeposited nickel coatings on magnetic and non-magnetic substrates -
Measurement of coating thickness - Magnetic method (ISO/DIS 2361:2024)
Elektrolytisch erzeugte Nickelschichten auf magnetischen und nichtmagnetischen
Grundmetallen- Messen der Schichtdicke- Magnetverfahren (ISO/DIS 2361:2024)
Revêtements électrolytiques de nickel sur substrat magnétique et non magnétique -
Mesurage de l’épaisseur du revêtement - Méthode magnétique (ISO/DIS 2361:2024)
Ta slovenski standard je istoveten z: prEN ISO 2361
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.40 Kovinske prevleke Metallic coatings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 2361
ISO/TC 107
Electrodeposited nickel coatings
Secretariat: KATS
on magnetic and non-magnetic
Voting begins on:
substrates — Measurement of
2024-08-14
coating thickness — Magnetic
Voting terminates on:
method
2024-11-06
Revêtements électrolytiques de nickel sur métal de base
magnétique et non magnétique — Mesurage de l'épaisseur —
Méthode magnétique
ICS: ISO ics
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 2361:2024(en)
DRAFT
ISO/DIS 2361:2024(en)
International
Standard
ISO/DIS 2361
ISO/TC 107
Electrodeposited nickel coatings
Secretariat: KATS
on magnetic and non-magnetic
Voting begins on:
substrates — Measurement of coating
thickness — Magnetic method
Voting terminates on:
Revêtements électrolytiques de nickel sur métal de base
magnétique et non magnétique — Mesurage de l'épaisseur —
Méthode magnétique
ICS: ISO ics
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: [phone]
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: [e-mail]
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 2361:2024(en)
ii
ISO/DIS 2361:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle of Measurement . 2
5 Factors affecting the measuring accuracy⁠⁠. 2
5.1 Type A coatings: Nickel on a magnetic substrate .2
5.1.1 Magnetic properties of the basis metal .2
5.1.2 Basis metal thickness .2
5.1.3 Direction of mechanical working of the basis metal .3
5.1.4 Residual magnetism .3
5.2 Type B coatings: nickel on a non-magnetic substrate- Coating on the back of the
substrate .3
5.3 Type A and B coatings .3
5.3.1 Coating thickness .3
5.3.2 Edge effects .3
5.3.3 Curvature .3
5.3.4 Surface roughness .3
5.3.5 Magnetic fields .4
5.3.6 Foreign particles .4
5.3.7 Magnetic properties of the coating .4
5.3.8 Probe pressure and orientation .4
5.3.9 Base Material thickness .4
6 Calibration of instruments . 4
6.1 General .4
6.2 Calibration standards .4
7 Procedure . 5
7.1 General .5
7.2 Basis metal thickness (type A coatings only) .5
7.3 Direction of mechanical working (type A coatings only) .5
7.4 Edge effects .5
7.5 Curvature .5
7.6 Number of readings .5
7.7 Residual magnetism (Type A coatings) .6
7.8 Surface cleanliness .6
7.9 Techniques .6
7.10 Positioning of the probe .6
7.11 Measuring on hot surfaces .6
7.12 Measuring underwater .6
8 Accuracy requirement . 6
9 Test report . 7

iii
ISO/DIS 2361:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared
...