iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 15882-2

(Main)

Extended application of results from fire resistance tests for service installations - Part 2: Dampers

Extended application of results from fire resistance tests for service installations - Part 2: Dampers

To provide guidance and rules to notified or accredited bodies (for Fire Dampers) to allow them to define the extended field of application for fire dampers. To identify the parameters that affects the fire resistance of dampers. In addition, to identify the factors that need to be considered when deciding whether, or by how much, the parameter can be extended when contemplating the fire resistance performance of an untested, or untestable variation in the construction.

Erweiterter Anwendungsbereich der Ergebnisse aus Feuerwiderstandsprüfungen für Installationen - Teil 2: Brandschutzklappen

Application étendue des résultats des essais de résistance au feu pour les installations de service - Partie 2: Clapets coupe-feu

La présente norme fournit aux organismes notifiés ou aux organismes accrédités (pour clapets coupe-feu)
des lignes directrices et des règles leur permettant de définir le domaine d’application étendue des clapets
coupe-feu. Elle identifie les paramètres affectant la résistance au feu des clapets. Elle identifie également,
dans le cas d’une étude de la performance de résistance au feu d’une variante de construction non encore
testée ou non vérifiable, les facteurs devant être pris en considération pour décider si un paramètre peut être
étendu et, dans ce cas, de combien.
La présente norme définit les principes permettant de tirer des conclusions sur l’influence de paramètres ou
de détails de construction spécifiques sur les critères pertinents à prendre en compte (E, I, S).
La présente norme ne s’applique pas aux volets de désenfumage.
Le présent document ne s’applique qu’aux domaines d’application étendue fondés sur des essais effectués
avec succès conformément à l’EN 1366-2. Le taux de fuite déterminé au cours de ces essais doit être
inférieur d’au moins 10 % aux limites indiquées dans l’EN 13501-3, établies pour E ou ES, en fonction de la
classification obtenue, avant de pouvoir appliquer les règles EXAP.
Une mise en oeuvre de la présente norme devrait permettre d’identifier les spécifications à vérifier pour
exploiter au mieux le domaine d’application. Certaines informations sur les programmes d’essai sont données
à titre purement indicatif.

Razširjena uporaba rezultatov preskusov požarne odpornosti servisnih inštalacij - 2. del: Lopute

General Information

Status
Not Published
Publication Date
07-Aug-2012
Withdrawal Date
07-Feb-2013
ICS
13.220.99 - Other standards related to protection against fire
Technical Committee
CEN/TC 127 - Fire safety in buildings
Drafting Committee
CEN/TC 127/WG 2 - Services
Current Stage
4098 - Decision to abandon - Enquiry
Start Date
09-Nov-2012
Completion Date
09-Nov-2012
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/117 - Horizontal complement to the mandates to CEN/CENELEC concerning the execution of standardization work for the valuation of construction products and elements in respect of their resistance to fire
Ref Project
oSIST prEN 15882-2:2011 - Extended application of results from fire resistance tests for service installations - Part 2: Dampers

Buy Standard

prEN 15882-2:2011prEN 15882-2:2011
PreviousNext
Draft
prEN 15882-2:2011
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15882-2:2011
01-januar-2011
Razširjena uporaba rezultatov preskusov požarne odpornosti servisnih inštalacij -
2. del: Lopute
Extended application of results from fire resistance tests for service installations - Part 2:
Dampers
Application étendue des résultats des essais de résistance au feu pour les installations
de service - Partie 2: Clapets coupe-feu
Ta slovenski standard je istoveten z: prEN 15882-2
ICS:
13.220.50 Požarna odpornost Fire-resistance of building
gradbenih materialov in materials and elements
elementov
oSIST prEN 15882-2:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15882-2:2011

---------------------- Page: 2 ----------------------
oSIST prEN 15882-2:2011


EUROPEAN STANDARD
DRAFT
prEN 15882-2
NORME EUROPÉENNE

EUROPÄISCHE NORM

October 2010
ICS 13.220.99
English Version
Extended application of results from fire resistance tests for
service installations - Part 2: Dampers

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 127.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15882-2:2010: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15882-2:2011
prEN 15882-2:2010 (E)
Contents Page
Foreword . 3
Introduction . 3
1 Scope. 4
2 Normative references . 4
3 Terms and definitions . 4
4 Determination of worst case . 5
5 Conditions and application rules . 6
5.1 Change of fixing damper to supporting construction . 6
5.2 Multiple damper assemblies . 6
5.3 Alternative penetration seals . 7
6 Influence of parameters and factors on fire damper performance . 7
7 Critical parameters and factors . 8
7.1 General . 8
7.2 Common operational parameters and factors .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15882-2:2022(Main)
Extended application of results from fire resistance tests for service installations - Part 2: Fire dampers
SIST EN 15882-2:2022

This document provides guidance and rules to notified bodies (for fire dampers) allowing them to produce/validate an extended field of application report for fire dampers based on testing undertaken in accordance with EN 1366 2. This document identifies the parameters that affect the fire resistance of fire dampers. It also identifies the factors that need to be considered when deciding whether, or by how much, the parameter can be extended when contemplating the fire resistance performance of an untested, or untestable variation in the construction.
This document explains the principles behind how a conclusion on the influence of specific parameters/constructional details relating to the relevant criteria (E, I, S) can be achieved.
This document does not cover dampers used for smoke control or non-mechanical fire barriers.
It is the intention that the application of this document makes it possible to identify which specifications to test to maximize the field of application. Some information on test programmes is given for guidance purposes.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15882-5:2021(Main)
Extended application of results from fire resistance tests for service installations - Part 5: Combined penetration seals
SIST EN 15882-5:2021

The purpose of this document is to provide the principles and guidance for the preparation of extended application documents for combined penetration seals where the systems were tested in accordance with (EN 1366-3 and EN 1366-1) or (EN 1366-3 and EN 1366-2). The field of the extended application document is additional to the direct field of application given within EN 1366-1, EN 1366-2 and EN 1366-3 and can be applied on a number of tests from each standard, which provide the relevant information for the formulation of an extended application.
This EXAP is intended to allow the penetration sealing of more than one service (e.g. cables, pipes, conduits) and four-sided fire resisting ducts (ventilation ducts) or fire dampers in the same penetration.
This EXAP is not used for extended applications in accordance with EN 1366-8, EN 1366-10 and/or EN 1366-12 (this will be dealt with in the next revision of the standard).

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13381-2:2014(Main)
Test methods for determining the contribution to the fire resistance of structural members - Part 2: Vertical protective membranes
SIST EN 13381-2:2014

This European Standard specifies a test method for determining the ability of a vertical protective membrane, when used as a fire resistant barrier, to contribute to the fire resistance (loadbearing capacity R) of loadbearing vertical structural building members fabricated from steel, concrete, steel/concrete composites or timber. The method described is applicable to any type of vertical protective membrane, which can be associated with a separate bracing membrane.
The vertical protective membrane can be either separated from or attached to the structural building member and is self-supporting. This test method is applicable to vertical protective membranes where there is a gap and a cavity between the vertical protective membrane and the structural building member, otherwise alternative test methods prEN 13381-3, EN 13381-4, EN 13381-6 or prEN 13381-7 should be used as appropriate.
This test method and assessment is not applicable to the following:
a) all situations where the cavity is to be used as a service or ventilation shaft;
b) all situations where the vertical protective membrane acts as a bracing membrane.
This European Standard contains the fire test which specifies the tests which shall be carried out whereby the vertical protective membrane together with the structural member to be protected is exposed to the specified fire. The fire exposure, to the standard temperature/time curve given in EN 1363-1, is applied to the side which would be exposed in practice.
The test method makes provision, through specified optional additional procedures, for the collection of data which can be used as direct input to the calculation of fire resistance according to the processes given in EN 1992-1-2, EN 1993-1-2, EN 1994-1-2 and EN 1995-1-2.
This European Standard also contains the assessment which provides information relative to the analysis of the test data and gives guidance for the interpretation of the results of the fire test, in terms of loadbearing capacity criteria of the protected vertical structural member.
The results of the fire test and the assessment can be applied, with certain defined provisions, to vertical structural building members which can be beams, columns or a combination of both and / or which could form part of a separating element or partition.
The limits of applicability of the results of the assessment arising from the fire test are defined, together with permitted direct application of the results to different structures, membranes and fittings.
In special circumstances, where specified in national building regulations, there can be a need to subject the protection material to a smouldering curve. The test for this and the special circumstances for its use are detailed in Annex B.
Tests should be carried out without additional combustible materials in the cavity.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15882-4:2012(Main)
Extended application of results from fire resistance tests for service installations - Part 4: Linear joint seals
SIST EN 15882-4:2012

This European standard specifies rules and prescribes the methodology for the preparation of extended application reports for linear joint sealing systems tested in accordance with EN 1366-4. The field of the extended application reports is additional to the direct field of application given in EN 1366-4. It may be applied to or based on a single test, or a number of tests, which provide the relevant information for the formulation of an extended application.
Mechanical metal seals are not part of the scope of this European standard.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15882-2:2022(Main)
Extended application of results from fire resistance tests for service installations - Part 2: Fire dampers
SIST EN 15882-2:2022

This document provides guidance and rules to notified bodies (for fire dampers) allowing them to produce/validate an extended field of application report for fire dampers based on testing undertaken in accordance with EN 1366 2. This document identifies the parameters that affect the fire resistance of fire dampers. It also identifies the factors that need to be considered when deciding whether, or by how much, the parameter can be extended when contemplating the fire resistance performance of an untested, or untestable variation in the construction.
This document explains the principles behind how a conclusion on the influence of specific parameters/constructional details relating to the relevant criteria (E, I, S) can be achieved.
This document does not cover dampers used for smoke control or non-mechanical fire barriers.
It is the intention that the application of this document makes it possible to identify which specifications to test to maximize the field of application. Some information on test programmes is given for guidance purposes.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 12101-11:2022(Main)
Smoke and heat control systems - Part 11: Horizontal flow powered ventilation systems for enclosed car parks
SIST-TS CEN/TS 12101-11:2022

This document gives minimum design, installation and commissioning requirements for powered smoke and heat control systems for enclosed car parks using horizontal flow powered ventilation, with or without sprinkler protection, on one or more levels, for cars and light commercial vehicles (max 3,5 t), to reach the design objectives outlined in this document .
This document is applicable for car parks with vehicles powered by petrol, diesel, electricity, CNG or LPG.
NOTE 1   For the purpose of this document for smoke ventilation systems, it is assumed that cars powered by electricity, CNG (compressed natural gas) or LPG (liquefied petroleum gas) will have similar HRR to vehicles powered by petrol or diesel.
NOTE 2   Cars powered by hydrogen are not covered by this document.
This document only covers traditional car parks that are with cars parked alongside each other, with common car access lanes. It does not cover other forms of car parking systems, such as stacking systems.
This document does not cover requirements for day‐to‐day ventilation.
Any other risks than fire from cars are not covered by this document.

  • Technical specification
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12101-13:2022(Main)
Smoke and heat control systems - Part 13: Pressure differential systems (PDS) - Design and calculation methods, installation, acceptance testing, routine testing and maintenance
SIST EN 12101-13:2022

This document gives calculation methods, guidance and requirements for the design, installation, acceptance testing, routine testing and maintenance for pressure differential systems (PDS).
PDSs are designed to hold back smoke at a leaky physical barrier in a building, such as a door (either open or closed) or other similarly restricted openings and to keep tenable conditions in escape and access routes depending on the application.
It covers systems intended to protect means of escape e.g. staircases, corridors, lobbies, as well as systems intended to provide a protected firefighting space (bridgehead) for the fire services.
It provides details on the critical features and relevant procedures for the installation.
It describes the commissioning procedures and acceptance testing criteria required to confirm that the calculated design is achieved in the building.
This document gives rules, requirements and procedures to design PDS for buildings up to 60 m.
For buildings taller than 60 m the same requirements are given (e.g. Table 1), but additional methods of calculation and verification are necessary. Requirements for such methods and verification are given in Annex D, but the methods fall outside the scope of this document [e.g. Additional mathematical analysis and/or Computational Fluid Dynamics (CFD)].
Routine testing and maintenance requirements are also defined in this document.
In the absence of national requirements and under expected ambient and outside conditions, the requirements in Table 1 are fulfilled by the PDS.

  • Standard
    118 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12101-6:2022(Main)
Smoke and heat control systems - Part 6: Specification for pressure differential systems - Kits
SIST EN 12101-6:2022

This document applies to pressure differential system kits and components, positioned on the market and intended to operate as part of a pressure differential system. The purpose of a pressure differential system is to prevent protected spaces from smoke spread by using pressure difference and airflow. This document specifies characteristics and test methods for components and kits for pressure differential systems to produce and control the required pressure differential and airflow between protected and unprotected space.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15882-5:2021(Main)
Extended application of results from fire resistance tests for service installations - Part 5: Combined penetration seals
SIST EN 15882-5:2021

The purpose of this document is to provide the principles and guidance for the preparation of extended application documents for combined penetration seals where the systems were tested in accordance with (EN 1366-3 and EN 1366-1) or (EN 1366-3 and EN 1366-2). The field of the extended application document is additional to the direct field of application given within EN 1366-1, EN 1366-2 and EN 1366-3 and can be applied on a number of tests from each standard, which provide the relevant information for the formulation of an extended application.
This EXAP is intended to allow the penetration sealing of more than one service (e.g. cables, pipes, conduits) and four-sided fire resisting ducts (ventilation ducts) or fire dampers in the same penetration.
This EXAP is not used for extended applications in accordance with EN 1366-8, EN 1366-10 and/or EN 1366-12 (this will be dealt with in the next revision of the standard).

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12101-2:2017(Main)
Smoke and heat control systems - Part 2: Natural smoke and heat exhaust ventilators
SIST EN 12101-2:2017

This European Standard applies to natural smoke and heat exhaust ventilators (NSHEV) operating as part of smoke and heat exhaust systems (NSHEVS), placed on the market. This standard specifies requirements and gives test methods for natural smoke and heat exhaust ventilators which are intended to be installed in smoke and heat control systems in buildings.

  • Standard
    88 pages
    English language
    sale 10% off
    e-Library read for
    1 day