iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 17405:2022

(Main)

Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2022)

Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2022)

This document specifies the techniques for manual ultrasonic testing of claddings on steel applied by welding, rolling and explosion using single-transducer or dual-transducer probes.
The test is intended to cover detection of two-dimensional or three-dimensional discontinuities in the cladding and in the region of the interface.
This document does not give acceptance criteria nor define the extent of testing.

Zerstörungsfreie Prüfung - Ultraschallprüfung - Techniken zur Prüfung von durch Schweißen, Walzen und Sprengen hergestellten Plattierungen (ISO 17405:2022)

Dieses Dokument legt die Techniken zur manuellen Ultraschallprüfung mit Einschwinger- oder SE-Prüfköpfen von Plattierungen auf Stahl fest, die durch Schweißen, Walzen und Sprengen aufgetragen wurden.
Die Prüfung ist dafür vorgesehen, den Nachweis von zweidimensionalen oder dreidimensionalen Inhomogenitäten in der Plattierung und in der Grenzfläche zu erbringen.
In diesem Dokument werden weder Zulässigkeitskriterien angegeben noch wird der Prüfumfang festgelegt.

Essais non destructifs - Contrôle par ultrasons - Technique d’essai des placages produits par soudage, laminage et explosion (ISO 17405:2022)

Le présent document spécifie les techniques d'essai manuel par ultrasons des revêtements sur acier appliqués par soudage, laminage et explosion en utilisant des traducteurs à transducteur simple et des traducteurs à émetteur et récepteur séparés.
L'essai est destiné à couvrir la détection des discontinuités bidimensionnelles ou tridimensionnelles présentes dans le revêtement et la région d'interface.
Le présent document ne fournit pas de critères d'acceptation et ne définit pas l'étendue des essais.

Neporušitveno preskušanje - Ultrazvočno preskušanje - Tehnika preskušanja oblog, pripravljenih z varjenjem, valjanjem in eksplozijo (ISO 17405:2022)

Ta dokument določa zahteve za ročno ultrazvočno preskušanje oblog na jeklu, ki se nanašajo
z varjenjem, valjanjem in eksplozijo, z uporabo sond, sestavljenih iz enega ali dveh pretvornikov.
Preskušanje je namenjeno odkrivanju dvodimenzionalnih ali tridimenzionalnih nezveznosti v
oblogi in v predelu vmesnika.
Ta dokument ne podaja kriterijev sprejemljivosti in ne določa obsega preskušanja.

General Information

Status
Published
Publication Date
24-May-2022
Withdrawal Date
29-Nov-2022
ICS
19.100 - Non-destructive testing
Technical Committee
CEN/TC 121 - Welding
Drafting Committee
CEN/TC 121/WG 21 - Testing of welds
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
25-May-2022
Completion Date
25-May-2022
Ref Project
SIST EN ISO 17405:2022 - Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2022)

Relations

Replaces
EN ISO 17405:2014 - Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014)
Effective Date
01-Jun-2022

Buy Standard

EN ISO 17405:2022EN ISO 17405:2022
PreviousNext
Standard
EN ISO 17405:2022
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 17405:2022
01-september-2022
Nadomešča:
SIST EN ISO 17405:2014
Neporušitveno preskušanje - Ultrazvočno preskušanje - Tehnika preskušanja
oblog, pripravljenih z varjenjem, valjanjem in eksplozijo (ISO 17405:2022)
Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by
welding, rolling and explosion (ISO 17405:2022)
Zerstörungsfreie Prüfung - Ultraschallprüfung - Techniken zur Prüfung von durch
Schweißen, Walzen und Sprengen hergestellten Plattierungen (ISO 17405:2022)
Essais non destructifs - Contrôle par ultrasons - Technique d’essai des placages produits
par soudage, laminage et explosion (ISO 17405:2022)
Ta slovenski standard je istoveten z: EN ISO 17405:2022
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
SIST EN ISO 17405:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 17405:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 17405:2022


EN ISO 17405
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2022
EUROPÄISCHE NORM
ICS 19.100 Supersedes EN ISO 17405:2014
English Version

Non-destructive testing - Ultrasonic testing - Technique of
testing claddings produced by welding, rolling and
explosion (ISO 17405:2022)
Essais non destructifs - Contrôle par ultrasons - Zerstörungsfreie Prüfung - Ultraschallprüfung -
Technique d'essai des placages produits par soudage, Techniken zur Prüfung von Plattierungen hergestellt
laminage et explosion (ISO 17405:2022) durch Schweißen, Walzen und Sprengen (ISO
17405:2022)
This European Standard was approved by CEN on 8 May 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17405:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 17405:2022
EN ISO 17405:2022 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 17405:2022
EN ISO 17405:2022 (E)
European foreword
This document (EN ISO 17405:2022) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2022, and conflicting national standards
shall be withdrawn at the latest by November 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 17405:2014.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 5580:2023(Main)
Non-destructive testing - Industrial radiographic illuminators - Minimum requirements (ISO 5580:2023)
SIST EN ISO 5580:2024

The function of an industrial radiographic illuminator is to provide sufficient diffuse light for viewing of developed radiographic films (radiographs).
This document specifies the minimum requirements for industrial radiographic illuminators used for viewing radiographs.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 7963:2022(Main)
Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 2 (ISO 7963:2022)
SIST EN ISO 7963:2023

This document specifies the requirements for the dimensions, material, manufacture and methods of use for calibration block No. 2 for setting and checking ultrasonic test equipment.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18563-1:2022(Main)
Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 1: Instruments (ISO 18563-1:2022)
SIST EN ISO 18563-1:2022

This document specifies the functional characteristics of multi-channel ultrasonic phased array instruments used for array probes and provides methods for their measurement and verification.
This document is also applicable to ultrasonic phased array instruments in automated systems; but other tests can be needed to ensure satisfactory performance. When the phased array instrument is a part of an automated system, the acceptance criteria can be modified by agreement between the parties involved.
This document also can partly be applicable to FMC instruments and TFM instruments.
This document gives the extent of the verification and defines acceptance criteria within a frequency range of 0,5 MHz to 10 MHz.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17391:2022(Main)
Non-destructive testing - Acoustic emission testing - In-service acoustic emission monitoring of metallic pressure equipment and structures - General requirements
SIST EN 17391:2022

This document specifies general requirements for in-service acoustic emission (AE) monitoring. It relates to detection, location and grading of AE sources with application to metallic pressure equipment and other structures such as bridges, bridge ropes, cranes, storage tanks, pipelines, wind turbine towers, marine applications, offshore structures. The monitoring can be periodic, temporary or continuous, on site or remote-controlled, supervised or automated. The objectives of AE monitoring are to define regions which are acoustically active as a result of damage or defect evolution.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17501:2022(Main)
Non-destructive testing - Thermographic testing - Active thermography with laser excitation
SIST EN 17501:2022

This document specifies a method and establishes guidelines for non-destructive testing using active thermography with laser excitation.
Active thermography with laser excitation is mainly applicable, but not limited, to different materials (e.g. composites, metals, ceramics) and to:
- the detection of surface-breaking discontinuities, particularly cracks;
- the detection of discontinuities located just below the surface or below coatings with an efficiency that diminishes rapidly with a few mm depth;
- the detection of disbonds and delamination parallel to the examined surface;
- the measurement of thermal material properties, like thermal diffusivity;
- the measurement of coating thickness.
The requirements for the equipment, for the verification of the system, for the surface condition of the test object, for the scanning conditions, for the recording, the processing and the interpretation of the results are specified. This document does not apply to the definition of acceptance criteria.
Active thermography with laser excitation can be applied in industrial production as well as in maintenance and repair (vehicle parts, engine parts, power plant, aerospace, etc.).

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9712:2022(Main)
Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2021)
SIST EN ISO 9712:2022

This document specifies requirements for the qualification and certification of personnel who perform industrial non-destructive testing (NDT) in the following methods.
a) acoustic emission testing;
b) eddy current testing;
c) leak testing (hydraulic pressure tests excluded);
d) magnetic testing;
e) penetrant testing;
f) radiographic testing;
g) strain gauge testing;
h) thermographic testing;
i) ultrasonic testing;
j) visual testing (direct unaided visual tests and visual tests carried out during the application of another NDT method are excluded).
The system specified in this document is also applicable to other NDT methods or to NDT techniques within an established NDT method, provided a comprehensive scheme of certification exists and the NDT method or NDT technique is covered by international, regional or national standards or the NDT method or the NDT technique has been demonstrated to be effective to the satisfaction of the certification body.
NOTE 1    The term "industrial" implies the exclusion of applications in the field of medicine.
NOTE 2    CEN/TR 14748 provides guidance on the methodology for qualification of non-destructive tests.
NOTE 3    This document specifies requirements for what are, in effect, third party conformity assessment schemes. These requirements do not directly apply to conformity assessment by second or first parties, but relevant parts of this document can be referred to in such arrangements.
NOTE 4    The term “direct unaided visual testing” implies where there is an uninterrupted optical path from the observer’s eye to the test area and the observer uses no tools or devices (e.g. mirror, endoscope, fibre optic).
NOTE 5    Calculations of strain based on other NDT methods are excluded.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4179:2021(Main)
Aerospace series - Qualification and approval of personnel for non-destructive testing
SIST EN 4179:2022

1.1 Purpose
This document establishes the minimum requirements for the qualification and certification of personnel performing non-destructive testing (NDT), non-destructive inspection (NDI), or non-destructive evaluation (NDE) in the aerospace manufacturing, service, maintenance and overhaul industries. For the purposes of this document, the term NDT will be used and will be considered equivalent to NDI and NDE.
In Europe, the term "approval" is used to denote a written statement by an employer that an individual meets specific requirements and has operating approval. The term "certification" as defined in 3.2 is used throughout this document as a substitute for the term "approval". Except when otherwise specified in the written practice, certification in accordance with this document includes operating approval.
1.2 Applicability
1.2.1 General
This document applies to personnel using NDT methods to test and/or accept materials, products, components, assemblies or sub-assemblies. This document also applies to personnel: directly responsible for the technical adequacy of the NDT methods used, who approve NDT procedures and/or work instructions, who audit NDT facilities, or who provide technical NDT support or training.
This document does not apply to individuals who only have administrative or supervisory authority over NDT personnel or to research personnel developing NDT technology for subsequent implementation and approval by a certified Level 3.
Personnel performing specialized inspections using certain direct readout instruments as determined by a Level 3 person certified in the test method, do not require qualification or certification to this document.
1.2.2 Implementation
This document addresses the use of a National Aerospace NDT Board (NANDTB). NANDTBs are only used as specified according to Annex C and it is not mandatory to have such a board for compliance with this document. Personnel certified to previous revisions of NAS 410 or EN 4179 need not recertify to the requirements of this document until their current certification expires.
1.3 Test Methods
1.3.1 Common test methods
This document contains detailed requirements for the following common NDT methods:
Eddy Current Testing   (ET)
Magnetic Particle Testing   (MT)
Penetrant Testing   (PT)
Radiographic Testing   (RT)
Thermographic Testing   (TT)
Ultrasonic Testing   (UT)
1.3.2 Other test methods
When invoked by engineering, quality, cognizant engineering organization or prime contractor requirements, this document applies to other current and emerging NDT methods used to determine the acceptability or suitability for intended service of a material, part, component, assembly or sub-assembly. Such test methods can include, but are not limited to, acoustic emission testing (AT), neutron radiography, leak testing, holography, and shearography. The requirements for personnel training, experience, and examination for these other test methods are established in accordance with 6.4 and are documented by the employer.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    39 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17290:2021(Main)
Non-destructive testing - Ultrasonic testing - Examination for loss of thickness due to erosion and/or corrosion using the TOFD technique
SIST EN 17290:2021

This document specifies the application of the time-of-flight diffraction (TOFD) technique in testing of metals for quantifying loss of thickness due to erosion and/or corrosion.
This document applies to all types of corrosion and/or erosion damage, particularly those defined in EN ISO 16809.
This document applies to unalloyed or low-alloyed steels.
It applies to components with a nominal thickness ≥ 6 mm. For smaller thicknesses, feasibility tests are performed to validate the test technique.
For other materials, feasibility tests are essential, too.
The TOFD technique can be used as a stand-alone technique or in combination with other non-destructive testing techniques, for in-service testing, in order to detect material loss caused by erosion and/or corrosion.
This technique is based on analysis of TOFD images using reflected and/or diffracted ultrasonic signals.
This document does not specify acceptance levels.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13477-2:2021(Main)
Non-destructive testing - Acoustic emission testing - Equipment characterisation - Part 2: Verification of operating characteristics
SIST EN 13477-2:2021

This document specifies test routines for the periodic verification of the performance of acoustic emission (AE) test equipment, i.e. sensors, pre-amplifiers, signal processors, external parametric inputs.
It is intended for use by qualified personnel to implement an automated verification process.
Verification of the measurement characteristics is advised after purchase of equipment, in order to obtain reference data for later verifications. Verification is also advised after repair, modifications, use under extraordinary conditions, or if one suspects a malfunction.
The procedures specified in this document do not exclude other qualified methods, e.g. verification in the frequency domain. These procedures apply in general unless the manufacturer specifies alternative equivalent procedures.
Safety aspects of equipment for use in potentially explosive zones are not considered in this document.

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16602-70-15:2021(Main)
Space product assurance - Non-destructive testing
SIST EN 16602-70-15:2021

This standard specifies NDI requirements for flight parts, components and structures used for space missions. It covers the NDI methods and stipulates the certification levels for personnel. The qualification of such processes are also specified for non-standard NDI techniques or where complex components are concerned. This standard also identifies the best practice across the large range of international and national standards.
Visual inspection included in this standard is not intended to include incoming inspection of, for example, raw materials, damage during transport, storage and handling and parts procurement verification.
The minimum requirements for NDI documentation are specified in the DRDs of the Annexes.
This standard does not cover the acceptance criteria of components, structures and parts submitted to this examination; it is expected that these criteria are identified on specific program application documentation.
This Standard does not apply to EEE components.
This standard may be tailored for the specific characteristic and constrains of a space project in conformance with ECSS-S-ST-00.

  • Standard
    106 pages
    English language
    sale 10% off
    e-Library read for
    1 day