Determination of explosion characteristics of dust clouds - Part 1: Determination of the maximum explosion pressure pmax of dust clouds

This document describes a test method for the determination of the maximum explosion pressure of dust clouds in a closed vessel under defined initial conditions of pressure and temperature.
This method is not suitable for use with recognised explosives, like gunpowder and dynamite, substances which do not require oxygen for combustion, pyrophoric substances, or substances or mixtures of substances which may under some circumstances behave in a similar manner. Where any doubt exists about the existence of hazard due to explosive properties, expert advice should be sought.

Bestimmung der Explosionskenngrößen von Staub/Luft-Gemischen - Teil 1: Bestimmung des maximalen Explosionsdruckes pmax von Staub/Luft-Gemischen

Dieses Dokument legt ein Prüfverfahren für die Bestimmung des maximalen Explosionsdruckes von Staubwolken in einem geschlossenen Behälter unter definierten Anfangsbedingungen von Druck und Temperatur fest. Dieses Verfahren ist nicht geeignet für Sprengstoffe wie Schießpulver und Dynamit sowie Stoffe, die ohne Sauerstoff verbrennen, pyrophore Stoffe oder Stoffe bzw. Stoffgemische, die sich unter bestimmten Umständen ähnlich verhalten. Wenn Zweifel über eventuell vorhandene Gefährdungen durch die Explosions-wirkung bestehen, sollten Fachleute zu Rate gezogen werden.

Détermination des caractéristiques d'explosion des nuages de poussière - Partie 1: Détermination de la pression maximale d'explosion pmax des nuages de poussière

La présente norme décrit une méthode d'essai permettant de déterminer la pression maximale d'explosion des
nuages de poussière dans un récipient fermé, dans des conditions initiales définies de pression et de température.
Cette méthode ne convient pas aux explosifs reconnus comme tels, comme la poudre et la dynamite, aux explosifs
dont la combustion ne nécessite pas d'oxygène, aux substances pyrophoriques ou aux substances ou mélanges
de substances pouvant, dans certaines circonstances, se comporter de manière similaire. Lorsqu'il existe un
doute sur l'existence d'un phénomène dangereux en raison de propriétés explosives, il convient de faire appel
à l'avis d'experts.

Ugotavljanje eksplozijskih značilnosti oblakov prahu - 1. del: Ugotavljanje najvišjega tlaka eksplozije pmax oblakov prahu

Ta dokument opisuje preskusno metodo za ugotavljanje najvišjega tlaka eksplozije oblakov prahu v zaprti posodi pod opredeljenimi začetnimi pogoji glede tlaka in temperature.
Ta metoda ni primerna za uporabo s priznanimi eksplozivi, kot so smodnik in dinamit, snovi, ki za izgorevanje ne potrebujejo kisika, piroforne snovi ali snovi ali zmesi snovi, ki se lahko v nekaterih okoliščinah podobno obnašajo. Kadar obstaja kakršen koli dvom o nevarnosti zaradi eksplozivnih lastnosti, je treba poiskati strokovni nasvet.

General Information

Status
Published
Publication Date
11-Jan-2011
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
08-Jan-2023

Relations

Buy Standard

Standard
EN 14034-1:2005+A1:2011 - BARVE
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.RWDYOMDQMHBestimmung der Explosionskenngrößen von Staub/Luft-Gemischen - Teil 1: Bestimmung des maximalen Explosionsdruckes pmax von Staub/Luft-GemischenDétermination des caractéristiques d'explosion des nuages de poussière - Partie 1: Détermination de la pression maximale d'explosion pmax des nuages de poussièreDetermination of explosion characteristics of dust clouds - Part 1: Determination of the maximum explosion pressure pmax of dust clouds13.230Varstvo pred eksplozijoExplosion protectionICS:Ta slovenski standard je istoveten z:EN 14034-1:2004+A1:2011SIST EN 14034-1:2005+A1:2011en,fr,de01-maj-2011SIST EN 14034-1:2005+A1:2011SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14034-1:2004+A1
January 2011 ICS 13.230 Supersedes EN 14034-1:2004English Version
Determination of explosion characteristics of dust clouds - Part 1: Determination of the maximum explosion pressure pmax of dust clouds
Détermination des caractéristiques d'explosion des nuages de poussière - Partie 1: Détermination de la pression maximale d'explosion pmax des nuages de poussière
Bestimmung der Explosionskenngrößen von Staub/Luft-Gemischen - Teil 1: Bestimmung des maximalen Explosionsdruckes pmax von Staub/Luft-Gemischen This European Standard was approved by CEN on 9 July 2004 and includes Amendment 1 approved by CEN on 13 November 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14034-1:2004+A1:2011: ESIST EN 14034-1:2005+A1:2011

Electro pneumatic valve . 17Annex B (normative)
Dust disperser with 5 mm holes . 19Annex C (normative)
20 l sphere . 23C.1General . 23C.2Test apparatus . 23C.3Test conditions . 23C.4Test procedure . 24C.5Calculation and correction of pmax . 25Annex ZA (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 94/9/EC"""" . 26Bibliography . 27
!". This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This document includes a Bibliography. This document is one of a series of standards as listed below:  EN 14034-1,Determination of explosion characteristics of dust clouds - Part 1: Determination of the maximum explosion pressure pmax of dust clouds;  !EN 14034-2", Determination of explosion characteristics of dust clouds - Part 2: Determination of the maximum rate of explosion pressure rise (dp/dt)max of dust clouds;  !EN 14034-3", Determination of explosion characteristics of dust clouds – Part 3: Determination of the lower explosion limit LEL of dust clouds;  EN 14034-4, Determination of explosion characteristics of dust clouds – Part 4: Determination of the limiting oxygen concentration LOC of dust clouds. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 14034-1:2005+A1:2011

!deleted text" SIST EN 14034-1:2005+A1:2011

This method is not suitable for use with recognised explosives, like gunpowder and dynamite, substances which do not require oxygen for combustion, pyrophoric substances, or substances or mixtures of substances which may under some circumstances behave in a similar manner. Where any doubt exists about the existence of hazard due to explosive properties, expert advice should be sought. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
!EN 14460", Explosion resistant equipment. 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 dust small solid particles in the atmosphere which settle out under their own weight, but which may remain suspended in air for some time (includes dust and grit, as defined in ISO 4225) NOTE Generally maximum particle size will not exceed 500 µm. 3.2 combustible dust dust able to undergo an exothermic reaction with air when ignited NOTE The terms “flammable” and “combustible” are used synonymously. 3.3 explosion pressure pex the highest overpressure occurring during an explosion of a dust cloud in a closed vessel 3.4 explosive atmosphere mixture with air, under atmospheric conditions, of flammable (combustible) substances in the form of gases, vapours, mists or dusts, in which, after ignition has occurred, combustion spreads to the entire unburned mixture 3.5 ignition delay tv time between the initiation of the dust dispersion and the activation of the ignition source 3.6 initial pressure pi the pressure in the explosion vessel at the moment of ignition SIST EN 14034-1:2005+A1:2011

20 bar. The apparatus shall be fitted with electrical and/or mechanical cut-offs as far as possible to ensure that any openings in the vessel (e.g. main door, instrument ports, inlet or outlet) are properly closed before a test procedure can start. The apparatus shall also be equipped as far as possible to ensure that any residual pressure inside the vessel is vented before the vessel can be opened. SIST EN 14034-1:2005+A1:2011

Key 1 Pressure sensor
5 Dust container 2 Chemical igniters
6 Fast acting valve 3 Inlet for purge air
7 Connecting tube 4 Dust disperser
8 Outlet for exhaust gas Figure 1 — 1 m³ vessel (schematic) SIST EN 14034-1:2005+A1:2011

4.3 Dust dispersion system (dust container, fast acting valve, connecting tube, dust disperser) The dust to be dispersed is charge
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.