EN 14035-38:2006
(Main)Fireworks - Part 38: Shot tubes - Specification and test methods
Fireworks - Part 38: Shot tubes - Specification and test methods
This European Standard specifies requirements for the construction, performance, primary packaging and labelling of shot tubes and the corresponding test methods. It is applicable to fireworks which are classified as shot tubes in categories 2 and 3 in EN 14035-2.
It is not applicable to shot tubes containing pyrotechnic composition which includes any of the following substances:
— arsenic or arsenic compounds;
— mixtures containing a mass fraction of chlorates greater than 80 %;
— mixtures of chlorates with metals;
— mixtures of chlorates with red phosphorus;
— mixtures of chlorates with potassium hexacyanoferrate(II);
— mixtures of chlorates with sulfur;
— mixtures of chlorates with sulfides;
— lead or lead compounds;
— mercury compounds;
— white phosphorus;
— picrates or picric acid;
— potassium chlorate with a mass fraction of bromates greater than 0,15 %;
— sulfur with an acidity, expressed as mass fraction of sulfuric acid, greater than 0,002 %;
— zirconium with a particle size of less than 40 mm.
NOTE In EN 14035-2, shot tubes are classified as follows:
— brief description: tube containing propellant charge and a pyrotechnic unit, with or without a transmitting fuse;
— principal effects: ejection of the pyrotechnic unit, producing a visual and/or aural effect in the air.
Schemes for type testing of shot tubes and batch testing of shot tubes are specified in Annex A and Annex B respectively.
Feuerwerkskörper - Teil 38: Feuerwerksrohre - Anforderungen und Prüfverfahren
Artifices de divertissement - Partie 38: Chandelles monocoup - Spécifications et méthodes d'essai
Le présent document spécifie les exigences de construction, de performances, d'emballage primaire et d’étiquetage des chandelles monocoup, ainsi que les méthodes d’essai correspondantes. Elle s’applique aux artifices de divertissement classés sous le nom de chandelles monocoup de catégories 2 et 3 dans l'EN 14035-2.
Elle ne s’applique pas aux chandelles monocoup dont la composition pyrotechnique comprend l’une des substances suivantes :
- arsenic ou composés d'arsenic ;
- mélanges contenant une fraction en masse de chlorates supérieure à 80 % ;
- mélanges de chlorates et de métaux ;
- mélanges de chlorates et de phosphore rouge ;
- mélanges de chlorates et d'hexacyanoferrate (II) de potassium ;
- mélanges de chlorates et de soufre ;
- mélanges de chlorates et de sulfures ;
- plomb ou composés de plomb ;
- composés de mercure ;
- phosphore blanc ;
- picrates ou acide picrique ;
- chlorate de potassium contenant une fraction en masse de bromates supérieure à 0,15 % ;
- soufre présentant une acidité, exprimée en fraction de masse d’acide sulfurique, supérieure à 0,002 % ;
- zirconium ayant une taille de particule inférieure à 40 mm.
NOTE Dans l’EN 14035-2, les chandelles monocoup sont classées comme suit :
- brève description : tube contenant une charge propulsive et un composant élémentaire, avec ou sans relais pyrotechnique ;
- effets principaux : éjection du composant élémentaire, produisant dans l’air un effet visuel et/ou sonore.
Les schémas d'essais de type et d'essais de lot des chandelles monocoup sont respectivement spécifiés aux Annexes A et B.
Ognjemet - 38. del: Tulci, enostrelni - Specifikacija in preskusne metode
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fireworks - Part 38: Shot tubes - Specification and test methodsOgnjemet - 38. del: Tulci, enostrelni - Specifikacija in preskusne metodeArtifices de divertissement - Partie 38: Chandelles monocoup - Spécifications et méthodes d'essaiFeuerwerkskörper - Teil 38: Feuerwerksrohre - Anforderungen und PrüfverfahrenTa slovenski standard je istoveten z:EN 14035-38:2006SIST EN 14035-38:2006en,fr,de71.100.30ICS:SLOVENSKI
STANDARDSIST EN 14035-38:200601-maj-2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14035-38February 2006ICS 71.100.30 English VersionFireworks - Part 38: Shot tubes - Specification and test methodsArtifices de divertissement - Partie 38: Chandellesmonocoup - Spécifications et méthodes d'essaiFeuerwerkskörper - Teil 38: Feuerwerksrohre -Anforderungen und PrüfverfahrenThis European Standard was approved by CEN on 30 December 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14035-38:2006: E
Type testing.20 Annex B (normative)
Batch testing.29 Annex C (normative)
Method for determination of smouldering rate of cigarette.33 Annex D (informative)
A-Deviations.34
Specifications (IEC 61672-1:2002) EN 61672-2, Electroacoustics — Sound level meters — Part 2: Pattern evaluation tests (IEC 61672-2:2003) EN ISO 845, Cellular plastics and rubbers — Determination of apparent (bulk) density (ISO 845:1988) EN ISO 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) EN ISO 2439, Flexible cellular polymeric materials — Determination of hardness (indentation technique) (ISO 2439:1997, including Technical Corrigendum 1:1998) ISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection ISO 3599, Vernier callipers reading to 0,1 and 0,05 mm 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 14035-1:2003 apply. 4 Construction 4.1 Means of ignition The means of ignition shall be identified by a protruding fuse. Conformity to this requirement shall be verified by visual examination. 4.2 Attachment of initial fuse The attachment of the protruding fuse to the shot tube shall be secure when tested in accordance with 8.1. 4.3 Protection of initial fuse 4.3.1 General The initial fuse shall be protected in one of the ways specified in 4.3.2, 4.3.3 or 4.3.4. 4.3.2 Initial fuse protected by fuse cover An orange fuse cover shall be in place over the initial fuse. Conformity to this requirement shall be verified by visual examination. 4.3.3 Initial fuse protected by primary pack or selection pack The shot tube shall be contained in a primary pack or selection pack conforming to Clause 6. Conformity to this requirement shall be verified by visual examination. 4.3.4 Protruding fuse designed to resist side ignition When tested in accordance with 8.6, the protruding fuse shall not ignite.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.