EN 16304:2013
(Main)Automatic vent valves for gas burners and gas burning appliances
Automatic vent valves for gas burners and gas burning appliances
This European Standard specifies the safety, construction and performance requirements for automatic vent valves for use with gas burners, gas appliances and similar use, hereafter referred to as ‘valves’.
This European Standard is applicable to:
- valves with declared maximum inlet pressures up to and including 500 kPa (5 bar) of nominal connection sizes up to and including DN 100 for use with one or more fuel gases in accordance with EN 437:2003+A1:2009;
- electrically operated valves;
- valves actuated by fluids where the control valves for these fluids are actuated electrically, but not to any external electrical devices for switching the control signal or actuating energy;
- valves fitted with open position indicator switches.
NOTE Provisions for final product inspection and testing by the manufacturer are not specified.
Automatische Abblaseventile für Gasbrenner und Gasgerät
Diese Europäische Norm legt die Sicherheits-, Bau- und Funktionsanforderungen an automatische Abblase-ventile zur Verwendung mit Gasbrennern, Gasgeräten und ähnlichen Anwendungen, nachstehend Ventile genannt, fest.
Diese Europäische Norm gilt für:
Ventile mit angegebenen höchsten Eingangsdrücken bis einschließlich 500 kPa (5 bar) und Nennweiten bis einschließlich DN 100, die für die Verwendung mit einem oder mehreren Brenngas(en) nach EN 437:2003+A1:2009 ausgelegt sind;
elektrisch betriebene Ventile und für Ventile, die durch Steuermedien angesteuert werden, wenn die Steuerventile für diese Medien elektrisch geschaltet werden; sie gilt nicht für externe elektrische Schalter, die das Steuersignal oder die Stellantriebsenergie beeinflussen;
Ventile mit Meldeschaltern für die Offenstellung.
ANMERKUNG Bestimmungen für die Prüfung von Endprodukten durch den Hersteller sind nicht festgelegt.
Robinets d'évent automatiques pour brûleurs à gaz et appareils à gaz
La présente Norme européenne spécifie les exigences de sécurité, de construction et de fonctionnement des robinets d’évent automatiques pour brûleurs à gaz, appareils à gaz et similaires, dénommés ci-après « robinets ».
La présente Norme européenne s'applique
- aux robinets dont la pression amont maximale déclarée est inférieure ou égale à 500 kPa (5 bar), de diamètres nominaux de raccordement inférieurs ou égaux à DN 100 utilisés avec un ou plusieurs combustibles gazeux conformément à l'EN 437:2003+A1:2009 ;
- aux robinets de sectionnement commandés électriquement ;
- aux robinets de sectionnement actionnés par des fluides où les vannes de commande de ces fluides sont commandées électriquement, mais en aucun cas aux dispositifs électriques externes commutant le signal de commande ou l’énergie motrice de commande ;
- aux robinets équipés de contacts indicateurs de position d'ouverture.
NOTE Les dispositions relatives aux contrôles et aux essais du produit final par le fabricant ne sont pas spécifiées.
Samodejni varnostno izpustni ventili za plinske gorilnike in plinske aparate
Ta evropski standard določa zahteve v zvezi z varnostjo, konstrukcijo in lastnostmi za samodejne ventilacijske ventile, ki se uporabljajo s plinskimi gorilniki, plinskimi aparati in podobnimi napravami (v nadaljnjem besedilu: »ventili«). Ta evropski standard se uporablja za: – ventile z deklariranim najvišjim vhodnim tlakom do vključno 500 kPa (5 bar) in nazivnimi velikostmi priključkov do vključno DN 100 za uporabo z enim ali več gorivnimi plini v skladu s standardom EN 437:2003+A1:2009; – električno upravljane ventile; – ventile, prožene s tekočino, pri katerih se ventili za upravljanje prožijo električno, vendar za preklapljanje pogonske energije ali krmilnega signala ne uporabljajo zunanjih električnih naprav; – ventile s kazalniki preklopa odprtega položaja.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Samodejni varnostno izpustni ventili za plinske gorilnike in plinske aparateAutomatische Abblaseventile für Gasbrenner und GasgerätRobinets d'évent automatiques pour brûleurs à gaz et appareils à gazAutomatic vent valves for gas burners and gas burning appliances27.060.20Plinski gorilnikiGas fuel burners23.060.40Pressure regulatorsICS:Ta slovenski standard je istoveten z:EN 16304:2013SIST EN 16304:2014en,fr,de01-januar-2014SIST EN 16304:2014SLOVENSKI
STANDARD
SIST EN 16304:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16304
March 2013 ICS 23.060.40 English Version
Automatic vent valves for gas burners and gas burning appliances
Robinets d'évent automatiques pour brûleurs à gaz et appareils à gaz
Automatische Abblaseventile für Gasbrenner und GasgerätThis European Standard was approved by CEN on 5 February 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16304:2013: ESIST EN 16304:2014
EN 16304:2013 (E) 2 Contents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Classification . 5 5 Units of measurement and test conditions . 6 6 Construction requirements . 6 7 Performance . 9 8 EMC/Electrical requirements . 13 9 Marking, installation and operating instructions . 15 Annex A (informative)
Gas connections in common use in the various countries . 18 Annex B (informative)
Leak-tightness test – volumetric method . 19 Annex C (informative)
Leak-tightness test – pressure loss method . 20 Annex D (normative)
Conversion of pressure loss into leakage rate . 21 Annex E (normative)
Electrical/electronic component fault modes . 22 Annex F (normative)
Additional requirements for safety accessories and pressure accessories as defined in EU Directive 97/23/EC . 23 Annex G (normative)
Materials for pressurised parts . 24 Annex H (informative)
Additional materials for pressurised parts . 25 Annex I (normative)
Requirements for controls used in DC supplied gas burn
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.