EN ISO 14405-2:2011/prA1

Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear sizes - Amendment 1 (ISO 14405-2:2011/DAM 1:2017)

2018-02-13: WI abandoned following ISO cancellation of equivalent WI (ISO notification in dataservice on 2018-02-09).

Geometrische Produktspezifikation (GPS) - Dimensionelle Tolerierung - Teil 2: Andere als lineare Maße - Änderung 1 (ISO 14405-2:2011/DAM 1:2017)

Spécification géométrique des produits (GPS) - Tolérancement dimensionnel - Partie 2: Dimensions autres que tailles linéaires - Amendement 1 (ISO 14405-2:2011/DAM 1:2017)

Specifikacija geometrijskih veličin izdelka (GPS) - Prikazovanje dimenzij in toleranc - 2. del: Dimenzije, ki niso linearne - Dopolnilo 1 (ISO 14405-2:2011/DAM 1:2017)

General Information

• Status: Not Published
• Publication Date: 01-Oct-2018
• Withdrawal Date: 01-Apr-2019
• ICS: 17.040.10 - Limits and fits
• ICS: 17.040.40 - Geometrical Product Specification (GPS)
• Technical Committee: CEN/TC 290 - Dimensional and geometrical product specification and verification
• Drafting Committee: CEN/TC 290 - Dimensional and geometrical product specification and verification
• Current Stage: 4098 - Decision to abandon - Enquiry
• Completion Date: 09-Feb-2018
• Ref Project: SIST EN ISO 14405-2:2012/oprA1:2017 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear sizes - Amendment 1 (ISO 14405-2:2011/DAM 1:2017)

Relations

• Amends: EN ISO 14405-2:2011 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear sizes (ISO 14405-2:2011)
• Effective Date: 08-Jun-2022
• Revised: EN ISO 14405-2:2019 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear or angular sizes (ISO 14405-2:2018)
• Effective Date: 21-Feb-2018

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2017
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND*363ULND]RYDQMHGLPHQ]LMLQ
WROHUDQFGHO'LPHQ]LMHNLQLVROLQHDUQH'RSROQLOR,62'$0

Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions
other than linear sizes - Amendment 1 (ISO 14405-2:2011/DAM 1:2017)
Geometrische Produktspezifikation (GPS) - Dimensionelle Tolerierung - Teil 2: Andere
als lineare Maße - Änderung 1 (ISO 14405-2:2011/DAM 1:2017)
Spécification géométrique des produits (GPS) - Tolérancement dimensionnel - Partie 2:
Dimensions autres que tailles linéaires - Amendement 1 (ISO 14405-2:2011/DAM
1:2017)1:2017)
Ta slovenski standard je istoveten z: EN ISO 14405-2:2011/prA1
ICS:
17.040.10 Tolerance in ujemi Limits and fits
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND*36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT AMENDMENT
ISO 14405-2:2011/DAM 1
ISO/TC 213 Secretariat: BSI
Voting begins on: Voting terminates on:
2017-06-07 2017-08-29
Geometrical product specifications (GPS) — Dimensional
tolerancing —
Part 2:
Dimensions other than linear sizes
AMENDMENT 1
Spécification géométrique des produits (GPS) — Tolérancement dimensionnel —
Partie 2: Dimensions autres que tailles linéaires
AMENDEMENT 1
ICS: 17.040.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 14405-2:2011/DAM 1:2017(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2017

ISO 14405-2:2011/DAM 1:2017(E)

© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 14405-2:2011/DAM 1:2017(E)
Geometrical product specifications (GPS) — Dimensional
tolerancing —
Part 2:
Dimensions other than linear sizes
AMENDMENT 1
Title:
Replace the text with the following:
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 2: Dimensions other than
linear or angular sizes
Introduction
Replace the first two paragraphs:
This document is a geometrical product specification (GPS) standard and is to be regarded as a general
GPS standard (see ISO 14638). It influences chain link A of the chain of standards on distance.
The ISO GPS Matrix model given in ISO 14638 gives an overview of the ISO GPS system of which this
document is a part. The fundamental rules of ISO GPS given in ISO 8015 apply to this document and
the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this
document, unless otherwise indicated.
1 Scope
st
1 paragraph
Replace the text with the following:
This document illustrates the use of geometrical tolerancing for dimensions that are not linear or
angular sizes to avoid the ambiguity caused by the use of ± tolerances on these dimensions. Both linear
and angular dimensions, except the size of features of size.
NOTE 2
Replace the text with the following:
For indications of size tolerances, see the following:
— ISO 14405-1 for linear size;
— ISO 14405-3 for angular size;
— ISO 2538-1 and ISO 2538-2 for wedges;
— ISO 3040 for cones.
2 Normative references
Update the years
ISO 14405-2:2011/DAM 1:2017(E)

From:
ISO 129-1:—), Technical drawings — Indication of dimensions and tolerances — Part 1: General
principles
To:
ISO 129-1, Technical drawings — Indication of dimensions and tolerances — Part 1: General principles
From:
ISO 1101:—, 2), Geometrical Product Specifications (GPS) — Geometrical tolerancing — Tolerances of
form, orientation, location and run-out
To:
ISO 1101, Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form,
orientation, location and run-out
From:
ISO 8015:2011, Geometrical product specifications (GPS) — Fundamentals — Concepts, principles
and rules
To:
ISO 8015, Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules
From:
ISO 13715:2000, Technical drawings — Edges of undefined shape — Vocabulary and indications
To:
ISO 13715, Technical product documentation — Edges of undefined shape — Indication and
dimensioning
From:
ISO 14405-1:2010, Geometrical product specifications (GPS) — Dimensional tolerancing — Linear sizes
To:
ISO 14405-1, Geometrical product specifications (GPS) — Dimensional tolerancing — Part
...