EN ISO 11357-4:2014
(Main)Plastics - Differential scanning calorimetry (DSC) - Part 4: Determination of specific heat capacity (ISO 11357-4:2014)
Plastics - Differential scanning calorimetry (DSC) - Part 4: Determination of specific heat capacity (ISO 11357-4:2014)
ISO 11357-4:2014 specifies methods for determining the specific heat capacity of plastics by differential scanning calorimetry.
Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC) - Teil 4: Bestimmung der spezifischen Wärmekapazität (ISO 11357-4:2014)
Dieser Teil von ISO 11357 legt Verfahren zur Bestimmung der spezifischen Wärmekapazität von Kunststoffen mittels Dynamischer Differenz-Thermoanalyse (Dynamischer Differenzkalorimetrie) fest.
Plastiques - Analyse calorimétrique différentielle (DSC) - Partie 4: Détermination de la capacité thermique massique (ISO 11357-4:2014)
L'ISO 11357-4:2014 spécifie des méthodes de détermination de la capacité thermique massique des plastiques par analyse calorimétrique différentielle.
Polimerni materiali - Diferenčna dinamična kalorimetrija (DSC) - 4. del: Ugotavljanje specifične toplotne kapacitete (ISO 11357-4:2014)
Standard EN ISO 11357-4 določa metode za ugotavljanje specifične toplotne kapacitete polimernih materialov z diferenčno dinamično kalorimetrijo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2014
1DGRPHãþD
SIST EN ISO 11357-4:2013
3ROLPHUQLPDWHULDOL'LIHUHQþQDGLQDPLþQDNDORULPHWULMD '6& GHO
8JRWDYOMDQMHVSHFLILþQHWRSORWQHNDSDFLWHWH ,62
Plastics - Differential scanning calorimetry (DSC) - Part 4: Determination of specific heat
capacity (ISO 11357-4:2014)
Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC) - Teil 4: Bestimmung der
spezifischen Wärmekapazität (ISO 11357-4:2014)
Plastiques - Analyse calorimétrique différentielle (DSC) - Partie 4: Détermination de la
capacité thermique massique (ISO 11357-4:2014)
Ta slovenski standard je istoveten z: EN ISO 11357-4:2014
ICS:
17.200.10 Toplota. Kalorimetrija Heat. Calorimetry
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 11357-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2014
ICS 83.080.01 Supersedes EN ISO 11357-4:2013
English Version
Plastics - Differential scanning calorimetry (DSC) - Part 4:
Determination of specific heat capacity (ISO 11357-4:2014)
Plastiques - Analyse calorimétrique différentielle (DSC) - Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC) -
Partie 4: Détermination de la capacité thermique massique Teil 4: Bestimmung der spezifischen Wärmekapazität (ISO
(ISO 11357-4:2014) 11357-4:2014)
This European Standard was approved by CEN on 10 July 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11357-4:2014 E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 11357-4:2014) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn
at the latest by December 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11357-4:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11357-4:2014 has been approved by CEN as EN ISO 11357-4:2014 without any modification.
INTERNATIONAL ISO
STANDARD 11357-4
Second edition
2014-06-15
Plastics — Differential scanning
calorimetry (DSC) —
Part 4:
Determination of specific heat
capacity
Plastiques — Analyse calorimétrique différentielle (DSC) —
Partie 4: Détermination de la capacité thermique massique
Reference number
ISO 11357-4:2014(E)
©
ISO 2014
ISO 11357-4:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
ISO 11357-4:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
4.1 General . 2
4.2 Continuous-scanning method . 3
4.3 Stepwise-scanning method . 4
5 Apparatus . 4
6 Test specimen . 4
7 Test conditions and specimen conditioning . 4
8 Procedure. 4
8.1 Selection of crucibles . 4
8.2 Setting up the apparatus and adjustment of isothermal baselines . 5
8.3 Measurement of specific heat capacity of calibration material . 6
8.4 Specimen run . 7
9 Determination of specific heat capacities . 7
9.1 Calculation of specific heat capacities. 7
9.2 Numerical rounding of the results . 7
10 Precision and bias . 8
11 Test report . 8
Annex A (informative) An approximate expression of the specific heat capacityof pure α-alumina
to
[3] [5]. 9
Bibliography .12
ISO 11357-4:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT), see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 5, Physical and
chemical properties.
This second edition cancels and replaces the first edition (ISO 11357-4:2005). This minor revision
contains the following changes:
a) all normative reference were changed into undated ones;
b) the term “pan” was replaced by “crucible” within the whole text;
c) the endothermic direction, a, was added in all figures and key.
ISO 11357 consists of the following parts, under the general title Plastics — Differential scanning
calorimetry (DSC):
— Part 1: General principles
— Part 2: Determination of glass transition temperature and glass transition step height
— Part 3: Determination of temperature and enthalpy of melting and crystallization
— Part 4: Determination of specific heat capacity
— Part 5: Determination of characteristic reaction-curve temperatures and times, enthalpy of reaction
and degree of conversion
— Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature
(dynamic OIT)
— Part 7: Determination of crystallization kinetics
iv © ISO 2014 – All rights reserved
INTERNATIONAL STANDARD ISO 11357-4:2014(E)
Plastics — Differential scanning calorimetry (DSC) —
Part 4:
Determination of specific heat capacity
1 Scope
This part of ISO 11357 specifies methods for determining the specific heat capacity of plastics by
differential scanning calorimetry.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for the application of this document. For undated references, the latest edition of the
referenced document (including any amendments) applies.
ISO 472, Plastics — Vocabulary
ISO 11357-1, Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles
ISO 80000-1, Quantities and units — Part 1: General
3 Ter
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.