EN ISO 4671:2007
(Main)Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671:2007)
Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671:2007)
ISO 4671:2007 specifies methods of measuring the inside diameter, outside diameter (including diameter over reinforcement of hydraulic hoses), wall thickness, concentricity and lining and cover thickness of hoses, methods of measurement and identification of the lengths of hoses and hose assemblies, and a method of verifying the through-bore of hydraulic hose assemblies.
Gummi- und Kunststoffschläuche und -schlauchleitungen - Verfahren zur Messung der Maße von Schläuchen und Längen von Schlauchleitungen (ISO 4671:2007)
Diese Europäische Norm legt Verfahren fest zur Messung der Innendurchmesser, Außendurchmesser
(einschließlich des Durchmessers über der Verstärkung von Hydraulikschläuchen), Wanddicke, Konzentrizität
und Dicke der Innenschicht und Außenschicht von Schläuchen, ein Verfahren zur Nachprüfung der
Durchgangsöffnung von Hydraulikleitungen sowie Verfahren zur Messung und Festlegung der Länge von
Schläuchen und Schlauchleitungen.
Tuyaux et flexibles en caoutchouc et en plastique - Méthodes de mesurage des dimensions des tuyaux et de la longueur des flexibles (ISO 4671:2007)
L'ISO 4671:2008 spécifie des méthodes de mesurage du diamètre intérieur, du diamètre extérieur (y compris le diamètre sur armature des flexibles hydrauliques), de l'épaisseur de paroi, de la concentricité, des épaisseurs du tube et du revêtement, des méthodes de mesurage et d'identification de la longueur des tuyaux et flexibles, ainsi qu'une méthode de vérification de l'alésage des flexibles hydrauliques.
Gumene in polimerne cevi ter cevni priključki - Metode merjenja dimenzij cevi ter dolžin cevnih priključkov (ISO 4671:2007)
Ta mednarodni standard določa metode merjenja notranjega premera, zunanjega premera (vključno s premerom nad ojačitvijo hidravličnih cevi), debeline sten, koncentričnost, obloge in debeline zunanje obloge, metode merjenja in prepoznavanja dolžin cevi in cevnih priključkov ter metode preverjanja izvrtine priključkov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2009
1DGRPHãþD
SIST EN ISO 4671:2001
*XPHQHLQSROLPHUQHFHYLWHUFHYQLSULNOMXþNL0HWRGHPHUMHQMDGLPHQ]LMFHYLWHU
GROåLQFHYQLKSULNOMXþNRY ,62
Rubber and plastics hoses and hose assemblies - Methods of measurement of the
dimensions of hoses and the lengths of hose assemblies (ISO 4671:2007)
Gummi- und Kunststoffschläuche und Schlauchleitungen - Verfahren zur Messung der
Maße von Schläuchen und Längen von Schlauchleitungen (ISO 4671:2007)
Tuyaux et flexibles en caoutchouc et en plastique - Méthodes de mesurage des
dimensions des tuyaux et de la longueur des flexibles (ISO 4671:2007)
Ta slovenski standard je istoveten z: EN ISO 4671:2007
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 4671
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2007
ICS 23.040.70; 83.140.40 Supersedes EN ISO 4671:2000
English Version
Rubber and plastics hoses and hose assemblies - Methods of
measurement of the dimensions of hoses and the lengths of
hose assemblies (ISO 4671:2007)
Tuyaux et flexibles en caoutchouc et en plastique - Gummi- und Kunststoffschläuche und Schlauchleitungen -
Méthodes de mesurage des dimensions des tuyaux et de la Verfahren zur Messung der Maße von Schläuchen und
longueur des flexibles (ISO 4671:2007) Längen von Schlauchleitungen (ISO 4671:2007)
This European Standard was approved by CEN on 28 November 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4671:2007: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Foreword
This document (EN ISO 4671:2007) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and
hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at
the latest by June 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4671:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 4671:2007 has been approved by CEN as a EN ISO 4671:2007 without any modification.
INTERNATIONAL ISO
STANDARD 4671
Third edition
2007-12-15
Rubber and plastics hoses and hose
assemblies — Methods of measurement
of the dimensions of hoses and the
lengths of hose assemblies
Tuyaux et flexibles en caoutchouc et en plastique — Méthodes de
mesurage des dimensions des tuyaux et de la longueur des flexibles
Reference number
ISO 4671:2007(E)
©
ISO 2007
ISO 4671:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 4671:2007(E)
Contents Page
Foreword. iv
1 Scope .1
2 Normative references .1
3 Test piece conditioning and temperature of measurement .1
4 Measurement of inside diameter.1
5 Measurement of outside diameter .3
6 Measurement of diameter over reinforcement .4
7 Measurement of wall thickness.4
8 Measurement of concentricity.5
9 Measurement of lining and cover thickness.6
10 Measurement of length and identification of measurement points.7
11 Verification of through-bore of hose assemblies.9
12 Test report .10
Bibliography .11
ISO 4671:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4671 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Hoses (rubber and plastics).
This third edition cancels and replaces the second edition (ISO 4671:1999), which has been technically
revised. The main changes are the following:
⎯ a clause has been added (Clause 3) specifying details of test piece conditioning and temperature of
measurement;
⎯ in 4.2, the use of tapered gauges has been added;
⎯ in Clause 4, an additional method of measuring the inside diameter has been included (4.8);
⎯ in Clause 5, an additional method of measuring the outside diameter has been included (5.6);
⎯ in 7.1, the parts of hoses at which readings are to be taken have been specified;
⎯ in 8.1, the parts of the hoses at which readings are to be taken have been specified;
⎯ in Clause 8, three additional methods of measuring the concentricity have been included (8.4, 8.5
and 8.6);
⎯ in 9.2, the method of measuring the lining and cover thickness has been modified.
iv © ISO 2007 – All rights reserved
INTERNATIONAL STANDARD ISO 4671:2007(E)
Rubber and plastics hoses and hose assemblies — Methods of
measurement of the dimensions of hoses and the lengths of
hose assemblies
1 Scope
This International Standard specifies methods of measuring the inside diameter, outside diameter (including
diameter over reinforcement of hydraulic hoses), wall thickness, concentricity and lining and cover thickness
of hoses, methods of measurement and identification of the lengths of hoses and hose assemblies, and a
method of verifying the through-bore of hydraulic hose assemblies.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 463, Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and
metrological characteristics of mechanical dial gauges
ISO 3599, Vernier callipers reading to 0,1 and 0,05 mm
ISO 3611, Micrometer callipers for external measurement
3 Test piece conditioning and temperature of measurement
3.1 Conditioning of test pieces
Unless otherwise specified, test pieces shall be taken at least 16 h after manufacture of the hose and
+°7
conditioned at 23 C for at least 3 h before measurement. This 3 h may be included in the 16 h.
−3
3.2 Measurement temperature
+7
Unless otherwise specified, the measurement temperature shall be 23 °C.
−3
4 Measurement of inside diameter
4.1 General
Measurements by methods 1 to 7 may be made either on the ends of a full length of hose or on a test piece
(minimum length 150 mm) cut from a full length. For wire-reinforced hydraulic hoses, measurements shall be
made at a minimum distance of 25 mm from the end of the hose.
Measurements shall be made using one of the following methods, as appropriate.
ISO 4671:2007(E)
4.2 Method 1
For inside diameters less than 150 mm and for all sizes of collapsible hose, plug gauges with 0,25 mm
increments in diameter (see Figure 1) and tapered gauges with 0,1 mm increments in diameter (see Figure 2)
may be used. Insert the gauge into the hose test piece gently without pressure. Take special care if the hose
bore is not precisely circular.
Dimensions in millimetres
Figure 1 — Plug gauges
Dimensions in millimetres
Figure 2 — Tapered gauges
4.3 Method 2
For inside diameters less than 63 mm, where greater accuracy is required, for example for wire-reinforced
hydraulic hoses, an expanding ball or telescopic gauge may be used.
4.4 Method 3
For all inside diameters up to and including 100 mm, the internal jaws of vernier slide callipers complying with
the requirements of ISO 3599 may be used. Make two measurements at right angles to each other and take
their average as the inside diameter. Take care not to distort the hose when making the measurements.
Callipers of suitable size may be used for nominal bores above 100 when greater accuracy than is obtainable
by Method 5 (see 4.6) is required.
4.5 Method 4
For all inside diameters, an internal calliper dial gauge (see ISO 463) with rounded feet designed for use in
bores made of elastomeric material may be
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.