EN 60286-1:2017

Packaging of components for automatic handling - Part 1: Tape packaging of components with axial leads on continuous tapes

IEC 60286-1:2017(E) applies to the tape packaging of components with axial leads for use in electronic equipment. In general, the tape is applied to the component leads. It covers requirements for taping techniques used with equipment for the preforming of leads, automatic handling, insertion and other operations, and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes. This edition includes the following significant changes with respect to the previous edition: a) a complete revision of the structure (detailed in Annex A) and reworked layout.

Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung - Teil 1: Gurtung von Bauelementen mit axialen Anschlüssen

Emballage des composants pour opérations automatisées - Partie 1: Emballage des composants à sorties axiales en bandes continues

L'IEC 60286-1:2017 est applicable à la mise en bande des composants à sorties axiales utilisés dans les équipements électroniques. En général, la bande est appliquée aux sorties des composants. Elle contient des exigences relatives aux techniques de mise en bande applicables pour l'utilisation des équipements de préformage des sorties, de manutention, d'insertion automatique et d'autres opérations. Elle fournit uniquement les dimensions essentielles pour la mise en bande de composants destinés aux opérations mentionnées ci-dessus. La présente édition inclut les modifications majeures suivantes par rapport à l'édition précédente: a) révision complète de la structure (détaillée à l' REF _Ref482173886 \r \h \* MERGEFORMAT Annexe A 08D0C9EA79F9BACE118C8200AA004BA90B02000000080000000E0000005F005200650066003400380032003100370033003800380036000000 ) et remaniement de la mise en page.

Pakiranje komponent za avtomatsko ravnanje - 1. del: Trakanje komponent z osnimi izvodi/priključki na neprekinjenih trakovih (IEC 60286-1:2017)

Ta del standarda IEC 60286 se uporablja za trakanje komponent z osnimi izvodi/priključki za uporabo v elektronski opremi. V splošnem se trak nanese na priključke komponent.
Standard zajema zahteve za tehnike tračnega pakiranja, ki se uporabljajo z opremo za izvedbo priključkov, samodejno upravljanje, vstavljanje in druge operacije, ter vključuje samo tiste dimenzije, ki so bistvene za tračno pakiranje komponent, ki se uporabljajo za zgoraj omenjene namene.

General Information

• Status: Published
• Publication Date: 16-Nov-2017
• Withdrawal Date: 29-Aug-2020
• ICS: 31.020 - Electronic components in general
• ICS: 31.240 - Mechanical structures for electronic equipment
• ICS: 55.060 - Spools. Bobbins
• Technical Committee: CLC/SR 40 - Capacitors and resistors for electronic equipment
• Drafting Committee: IEC/TC 40 - IEC_TC_40
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 17-Nov-2017
• Completion Date: 17-Nov-2017
• Ref Project: SIST EN 60286-1:2018 - Packaging of components for automatic handling - Part 1: Tape packaging of components with axial leads on continuous tapes (IEC 60286-1:2017)

Relations

• Replaces: EN 60286-1:1998 - Packaging of components for automatic handling - Part 1: Tape packaging of components with axial leads on continuous tapes
• Effective Date: 21-Nov-2017
• Amended By: EN 60286-1:2017/A1:2021 - Packaging of components for automatic handling - Part 1: Tape packaging of components with axial leads on continuous tapes
• Effective Date: 24-Mar-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST EN 60286-1:2002
3DNLUDQMHNRPSRQHQW]DDYWRPDWVNRUDYQDQMHGHO7UDNDQMHNRPSRQHQW]
RVQLPLL]YRGLSULNOMXþNLQDQHSUHNLQMHQLKWUDNRYLK,(&
Packaging of components for automatic handling - Part 1: Tape packaging of
components with axial leads on continuous tapes (IEC 60286-1:2017)
Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung - Teil 1:
Gurtung von Bauelementen mit axialen Anschlüssen (IEC 60286-1:2017)
Emballage des composants pour opérations automatisées - Partie 1: Emballage des
composants à sorties axiales en bandes continues (IEC 60286-1:2017)
Ta slovenski standard je istoveten z: EN 60286-1:2017
ICS:
31.020 Elektronske komponente na Electronic components in
splošno general
55.060 Tulci. Vretena Spools. Bobbins
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60286-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2017
ICS 31.020; 31.240 Supersedes EN 60286-1:1998
English Version
Packaging of components for automatic handling -
Part 1: Tape packaging of components with axial leads
on continuous tapes
(IEC 60286-1:2017)
Emballage des composants pour opérations automatisées - Gurtung und Magazinierung von Bauelementen für
Partie 1: Emballage des composants à sorties axiales automatische Verarbeitung - Teil 1: Gurtung von
en bandes continues Bauelementen mit axialen Anschlüssen
(IEC 60286-1:2017) (IEC 60286-1:2017)
This European Standard was approved by CENELEC on 2017-08-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60286-1:2017 E
European foreword
The text of document 40/2538/FDIS, future edition 3 of IEC 60286-1, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60286-1:2017.

The following dates are fixed:
(dop) 2018-05-30
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2020-08-30
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60286-1:1998.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60286-1:2017 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60286-2 NOTE Harmonized as EN 60286-2.
IEC 60286-3 NOTE Harmonized as EN 60286-3.
IEC 60301 NOTE Harmonized as EN 60301.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year

IEC 60294 -  Measurement of the dimensions of a EN 60294 -
cylindrical component with axial
terminations
ISO 11469 -  Plastics - Generic identification and EN ISO 11469 -
marking of plastics products
IEC 60286-1 ®
Edition 3.0 2017-07
INTERNATIONAL
STANDARD
Packaging of components for automatic handling –

Part 1: Tape packaging of components with axial leads on continuous tapes

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 31.020; 31.240 ISBN 978-2-8322-4645-0

– 2 – IEC 60286-1:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Dimensions. 5
4.1 Dimensions common to tapes and taped components with axial leads . 5
4.1.1 General . 5
4.1.2 Body location (permissible lateral deviation) . 7
4.1.3 Tape spacing . 7
4.2 Taping . 7
4.2.1 General . 7
4.2.2 Orientation of polarized components . 8
4.2.3 Position, kinks and bends of the leads . 8
4.2.4 The ends of the leads . 8
4.2.5 Holding in the tape . 8
4.2.6 Requirements of tape material, storage, and handling . 8
4.2.7 Splices of tape . 8
4.2.8 Leader tape . 8
5 Packing . 8
5.1 General . 8
5.2 Dimensions of the reel . 9
5.3 Distances W and W . 9
1 2
5.4 Recycling . 9
5.5 Protection of components . 9
5.6 Reel filling . 9
5.7 Dimensions of the fan-fold container . 10
5.8 Missing components . 10
6 Marking . 10
Annex A (informative) Cross-reference for references to the previous edition of this
document . 11
Bibliography . 12

Figure 1 – Dimensions for tape packaging of components with axial leads . 6
Figure 2 – Reel dimensions . 9
Figure 3 – Outer dimensions of the fan-fold arrangement . 10

Table 1 – Tape widths and permissible variation . 6
Table 2 – Component spacing and permissible deviation . 7
Table 3 – Tape spacing. 7
Table A.1 – Cross-reference to clauses . 11

IEC 60286-1:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
PACKAGING OF COMPONENTS FOR AUTOMATIC HANDLING –

Part 1: Tape packaging of components
with axial leads on continuous tapes

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60286-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This third edition cancels and replaces the second edition published in 1997. This edition
consti
...