Live working - Insulating sticks and attachable devices - Part 2: Attachable devices

IEC 60832-2:2010 gives the essential requirements for devices that can be attached onto and removed from the fitting of the insulating sticks for live working, for use on a.c. electrical installations. Products designed and manufactured according to this standard contribute to the safety of the users provided they are used by skilled persons, in accordance with safe methods of work and the instructions for use. IEC 60832-1:2010 and IEC 60832-2:2010 cancel and replace the first edition of IEC 60832 published in 1988. The two parts have been created to clearly separate the requirements and testing of insulating sticks from those of attachable universal devices. Compared to IEC 60832, the major changes included in IEC 60832-2 are: - updating of the list of devices; - clarifying the applicability of the document to other attachment system than splined end-fitting; - application of conformity assessment for products having completed the production phase, according to IEC 61318:2007 (Edition 3), focusing on the classification of defects and the introduction of alternative testing in case of production follow-up.

Arbeiten unter Spannung - Isolierende Stangen und auswechselbare Arbeitsköpfe - Teil 2: Auswechselbare Arbeitsköpfe

Travaux sous tension - Perches isolantes et outils adaptables - Partie 2: Outils adaptables

La CEI 60832-2:2010 définit les exigences essentielles des outils qui peuvent être attachés ou détachés du bout des perches isolantes pour travaux sous tension, pour une utilisation sur des installations électriques à courant alternatif. Les produits conçus et fabriqués en conformité avec la présente norme contribuent à la sécurité des utilisateurs, pourvu qu'ils soient utilisés par des personnes qualifiées, conformément à des méthodes de travail en toute sécurité et aux instructions d'emploi. La CEI 60832-1:2010 et la CEI 60832-2:2010 annulent et remplacent la première édition de la CEI 60832 publiée en 1988. Les deux parties ont été créées pour séparer clairement les exigences et les essais des perches isolantes de ceux des outils adaptables. Par rapport à la CEI 60832, les principales modifications introduites dans la CEI 60832-2 sont: - la mise à jour de la liste d'outils; - la clarification de l'application du document à d'autres systèmes de fixation que l'embout cranté; - l'évaluation de la conformité des produits issus de la production selon les dispositions définies dans la CEI 61318:2007 (Edition 3) en s'appliquant à classifier les défauts et à introduire des essais alternatifs pour le suivi de la production.

Delo pod napetostjo - Izolacijske palice in priklopne naprave - 2. del: Priklopne naprave (IEC 60832-2:2010)

Ta del IEC 60832 podaja bistvene zahteve za naprave, ki se lahko pritrdijo na fiting izolacijske palice za delo pod napetostjo in snamejo z njega, za uporabo na električnih inštalacijah z izmeničnim tokom. Del 1 IEC 60832 zajema izolacijske palice. V tem delu standarda se izraz »naprava« uporablja za »priklopno napravo«, razen če je določeno drugače. Proizvodi, zasnovani in narejeni v skladu s tem standardom, prispevajo k varnosti uporabnikov pod pogojem, da jih uporabljajo usposobljene osebe v skladu z varnimi metodami dela in navodili za uporabo.

General Information

Status
Published
Publication Date
18-Mar-2010
Current Stage
6060 - Document made available
Start Date
19-Mar-2010
Due Date
18-Apr-2010
Completion Date
19-Mar-2010

RELATIONS

Buy Standard

Standard
EN 60832-2:2010
English language
64 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 60832-2:2010
01-junij-2010

Delo pod napetostjo - Izolacijske palice in priklopne naprave - 2. del: Priklopne

naprave (IEC 60832-2:2010)

Live working - Insulating sticks and attachable devices - Part 2: Attachable devices (IEC

60832-2:2010)
Arbeiten unter Spannung - Isolierende Arbeitsstangen und auswechselbare

Adapter/Arbeitsköpfe - Teil 2: Auswechselbare Adapter/Arbeitsköpfe (IEC 60832-2:2010)

Travaux sous tension - Perches isolantes et outils adaptables - Partie 2: Outils
adaptables (CEI 60832-2:2010)
Ta slovenski standard je istoveten z: EN 60832-2:2010
ICS:
13.260 9DUVWYRSUHGHOHNWULþQLP Protection against electric
XGDURP'HORSRGQDSHWRVWMR shock. Live working
29.260.01 (OHNWULþQDRSUHPD]DGHORY Electrical equipment for
SRVHEQLKUD]PHUDKQD working in special conditions
VSORãQR in general
SIST EN 60832-2:2010 en,fr

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 60832-2:2010
---------------------- Page: 2 ----------------------
SIST EN 60832-2:2010
EUROPEAN STANDARD
EN 60832-2
NORME EUROPÉENNE
March 2010
EUROPÄISCHE NORM
ICS 13.260; 29.240.20. Supersedes EN 60832:1996 (partially)
English version
Live working -
Insulating sticks and attachable devices -
Part 2: Attachable devices
(IEC 60832-2:2010)
Travaux sous tension - Arbeiten unter Spannung -
Perches isolantes et outils adaptables - Isolierende Stangen und auswechselbare
Partie 2: Outils adaptables Adapter/Arbeitsköpfe -
(CEI 60832-2:2010) Teil 2: Auswechselbare
Adapter/Arbeitsköpfe
(IEC 60832-2:2010)

This European Standard was approved by CENELEC on 2010-03-01. CENELEC members are bound to comply

with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on

application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CENELEC member into its own language and notified

to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,

the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60832-2:2010 E
---------------------- Page: 3 ----------------------
SIST EN 60832-2:2010
EN 60832-2:2010 - 2 -
Foreword

The text of document 78/839/FDIS, future edition 1 of IEC 60832-2, prepared by IEC TC 78, Live working,

was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60832-2 on

2010-03-01.

This EN 60832-2, together with EN 60832-1, supersedes EN 60832:1996. The two parts have been

created to clearly separate the requirements and testing of insulating sticks from those of attachable

universal devices.
Compared to EN 60832, the major changes included in EN 60832-2 are:
− updating of the list of devices;

− clarifying the applicability of the document to other attachment system than splined end-fitting;

− application of conformity assessment for products having completed the production phase, according

to IEC 61318:2007 (Edition 3), focusing on the classification of defects and the introduction of

alternative testing in case of production follow-up.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent

rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2010-12-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2013-03-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice

The text of the International Standard IEC 60832-2:2010 was approved by CENELEC as a European

Standard without any modification.
__________
---------------------- Page: 4 ----------------------
SIST EN 60832-2:2010
- 3 - EN 60832-2:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.

NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD

applies.
Publication Year Title EN/HD Year
IEC 60060-1 - High-voltage test techniques - HD 588.1 S1 -
Part 1: General definitions and test
requirements
IEC 60212 1971 Standard conditions for use prior to and HD 437 S1 1984
during the testing of solid electrical insulating
materials
IEC 60417 Graphical symbols for use on equipment - -
IEC 61318 2007 Live working - Conformity assessment EN 61318 2008
applicable to tools, devices and equipment
IEC 61477 - Live working - Minimum requirements for the EN 61477 -
utilization of tools, devices and equipment
---------------------- Page: 5 ----------------------
SIST EN 60832-2:2010
---------------------- Page: 6 ----------------------
SIST EN 60832-2:2010
IEC 60832-2
Edition 1.0 2010-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Live working – Insulating sticks and attachable devices –
Part 2: Attachable devices
Travaux sous tension – Perches isolantes et outils adaptables –
Partie 2: Outils adaptables
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX
ICS 13.260; 29.240.20; 29.260.99 ISBN 2-8318-1077-7
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60832-2:2010
– 2 – 60832-2 © IEC:2010
CONTENTS

FOREWORD...........................................................................................................................5

INTRODUCTION.....................................................................................................................7

1 Scope...............................................................................................................................8

2 Normative references .......................................................................................................8

3 Terms, definitions and symbols ........................................................................................8

3.1 Terms and definitions ..............................................................................................8

3.2 Symbols ..................................................................................................................9

4 Requirements ...................................................................................................................9

4.1 General ...................................................................................................................9

4.2 Dimensional and mechanical requirements..............................................................9

4.2.1 Dimensional requirements ...........................................................................9

4.2.2 Mechanical requirements...........................................................................10

4.3 Mechanical protection ...........................................................................................12

4.4 Protection against corrosion ..................................................................................12

4.5 Marking .................................................................................................................12

4.6 Instructions for use................................................................................................12

5 Tests ..............................................................................................................................13

5.1 General .................................................................................................................13

5.2 Visual inspection ...................................................................................................13

5.3 Dimensional check ................................................................................................13

5.4 Compatibility check ...............................................................................................13

5.5 Durability of marking .............................................................................................13

5.6 Mechanical tests and specific tests........................................................................14

5.6.1 Universal adaptor and hook stick adaptor ..................................................14

5.6.2 Formed-wire ring – Tension of the spigot...................................................15

5.6.3 Locating drift – Bending test ......................................................................16

5.6.4 Conductor cleaning brush – Semi-tubular type...........................................17

5.6.5 Conductor cleaning brush – V-shaped type – Fatigue test .........................19

5.6.6 Oilcan – Functioning of the operating lever................................................19

5.6.7 Ratchet spanner (ratchet wrench) – Friction ..............................................19

5.6.8 Spanner (wrench) – Torsion test................................................................20

5.6.9 Retaining pin remover ...............................................................................20

5.6.10 Holding fork – Bending test........................................................................24

5.6.11 Retaining device installer/remover – Bending test......................................24

5.6.12 Binding wire cutter blade (tie wire cutter) – Bending test............................25

5.6.13 Rotary blade – Tension test.......................................................................27

5.6.14 Rotary prong – Tension test.......................................................................27

5.6.15 Adjustable pliers........................................................................................28

5.6.16 Vice-grip pliers ..........................................................................................29

5.6.17 Adjustable insulator fork ............................................................................31

5.6.18 All-angle pliers ..........................................................................................33

5.6.19 Pin holder..................................................................................................34

5.6.20 Flexible spanner head (flexible wrench head) – Torsion test......................36

5.6.21 Ammeter holder .........................................................................................36

5.6.22 Anti-interference braid applicator...............................................................39

5.6.23 Hack saw – Bending test ...........................................................................40

---------------------- Page: 8 ----------------------
SIST EN 60832-2:2010
60832-2 © IEC:2010 – 3 –

5.6.24 Mirror ........................................................................................................41

5.6.25 Conductor gauge .......................................................................................42

5.6.26 Gap gauge.................................................................................................44

5.6.27 Clevis and tongue stick devices – Tension test..........................................45

5.7 Instructions for use................................................................................................46

5.7.1 Type test ...................................................................................................46

5.7.2 Alternative test in case of attachable devices having completed the

production phase.......................................................................................46

6 Conformity assessment of devices having completed the production phase....................46

7 Modifications ..................................................................................................................46

Annex A (informative) Attachment system of sticks – Examples ...........................................47

Annex B (normative) Suitable for live working ; double triangle (IEC 60417–5216

(2002-10)).............................................................................................................................49

Annex C (normative) Chronology of type tests .....................................................................50

Annex D (normative) Classification of defects and tests to be allocated ...............................55

Annex E (informative) In-service recommendations..............................................................60

Bibliography..........................................................................................................................61

Figure 1 – Test set-up for a hook stick adaptor – Torsion and tension of the adaptor ............14

Figure 2 – Universal adaptor and hook stick adaptor – Torsion of the wing screw ................15

Figure 3 – Formed-wire ring – Tension of the spigot .............................................................16

Figure 4 – Locating drift – Bending test.................................................................................17

Figure 5 – Conductor cleaning brush – Fatigue test on semi-tubular type..............................17

Figure 6 – Conductor cleaning brush – Semi-tubular type – Crushing test.............................18

Figure 7 – Conductor cleaning brush – V-shaped type – Fatigue test ....................................19

Figure 8 – Spanner (wrench) – Torsion test ..........................................................................20

Figure 9 – Spiral type retaining pin remover – Torsion test ...................................................21

Figure 10 – Fine-point type retaining pin remover – Torsion test ...........................................22

Figure 11 – Cam type (pry type) retaining pin remover – Bending test ..................................23

Figure 12 – Holding fork – Bending test ................................................................................24

Figure 13 – Retaining device installer/remover – Bending test ..............................................25

Figure 14 – Binding wire cutter blade (tie wire cutter) – Bending test ....................................26

Figure 15 – Rotary blade – Tension test ...............................................................................27

Figure 16 – Rotary prong – Tension test ...............................................................................28

Figure 17 – Adjustable pliers – Tightening capability.............................................................28

Figure 18 – Adjustable pliers – Bending test .........................................................................29

Figure 19 – Vice-grip pliers – Tightening capability – Blocking and unblocking of the

handle ..................................................................................................................................30

Figure 20 – Adjustable insulator fork – Torsion of the attachment system .............................31

Figure 21 – Adjustable insulator fork – Bending test .............................................................32

Figure 22 – Adjustable insulator fork – Articulation test.........................................................32

Figure 23 – All-angle pliers – Tightening capability ...............................................................33

Figure 24 – All-angle pliers – Bending test............................................................................34

Figure 25 – Pin holder – Resistance of the spring .................................................................35

Figure 26 – Pin holder – Bending test ...................................................................................35

---------------------- Page: 9 ----------------------
SIST EN 60832-2:2010
– 4 – 60832-2 © IEC:2010

Figure 27 – Ammeter holder – Torsion test ...........................................................................36

Figure 28 – Ammeter holder – Shock test .............................................................................38

Figure 29 – Anti-interference braid applicator – Controlling the sliding rod ............................39

Figure 30 – Anti-interference braid applicator – Bending test ................................................40

Figure 31 – Hack saw – Bending test mounting.....................................................................41

Figure 32 – Mirror – Friction test...........................................................................................42

Figure 33 – Conductor gauge – Testing the slide ..................................................................43

Figure 34 – Conductor gauge – Distortion of the gauge body ................................................43

Figure 35 – Gap gauge – Tension test ..................................................................................44

Figure 36 – Gap gauge – Electrical test ................................................................................45

Figure A.1 – First example....................................................................................................47

Figure A.2 – Second example ...............................................................................................48

Table 1 – Mechanical characteristics of splined end devices (to be supplied by the

manufacturer) .......................................................................................................................11

Table 2 – Mechanical characteristics of clevis and tongue stick devices (to be supplied

by the manufacturer).............................................................................................................12

Table C.1 – Type tests for splined end devices .....................................................................50

Table C.2 – Type tests for clevis and tongue stick devices....................................................54

Table D.1 – Classification of defects and associated requirements and tests for splined

end devices ..........................................................................................................................55

Table D.2 – Classification of defects and associated requirements and tests for clevis

and tongue stick devices.......................................................................................................59

---------------------- Page: 10 ----------------------
SIST EN 60832-2:2010
60832-2 © IEC:2010 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LIVE WORKING – INSULATING STICKS
AND ATTACHABLE DEVICES –
Part 2: Attachable devices
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60832-2 has been prepared by IEC technical committee 78: Live

working.

The first edition of IEC 60832-1 and that of IEC 60832-2 cancel and replace the first edition of

IEC 60832 published in 1988. The two parts have been created to clearly separate the

requirements and testing of insulating sticks from those of attachable universal devices.

Compared to IEC 60832, the major changes included in IEC 60832-2 are:
• updating of the list of devices;

• clarifying the applicability of the document to other attachment system than splined

end-fitting;

• application of conformity assessment for products having completed the production

phase, according to IEC 61318:2007 (Edition 3), focusing on the classification of

defects and the introduction of alternative testing in case of production follow-up.

---------------------- Page: 11 ----------------------
SIST EN 60832-2:2010
– 6 – 60832-2 © IEC:2010
The text of this standard is based on the following document:
FDIS Voting report
78/839/FDIS 78/845/RVD

Full information on the voting for the approval of this standard can be found in the report on

voting indicated in the above table.

This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

A list of all parts of the IEC 60832 series, published under the general title Live working –

Insulating sticks and attachable devices, can be found on the IEC website.

The committee has decided that the contents of this publication will remain unchanged until

the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data

related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The “colour inside” logo on the cover page of this publication indicates

that it contains colours which are considered to be useful for the correct understanding

of its contents. Users should therefore print this publication using a colour printer.

---------------------- Page: 12 ----------------------
SIST EN 60832-2:2010
60832-2 © IEC:2010 – 7 –
INTRODUCTION

The purpose of this standard is to provide essential requirements. Each user of this standard

may supplement it with their own requirements. For example, the user may add requirements

regarding the use of attachable devices on d.c. electrical installations or the mechanical

performance or compatibility and interchangeability with tools already in service. In such

cases, caution should be taken to maintain or improve the performance of the products.

This publication has been prepared in accordance with the requirements of IEC 61477.

The products designed and manufactured according to this standard contribute to the safety

of the users provided they are used by skilled persons, in accordance with safe methods of

work and the instructions for use.

The product covered by this standard may have an impact on the environment during some or

all stages of its life cycle. These impacts can range from slight to significant, be of short-term

or long-term, and occur at the global, regional or local level.

Except for a disposal statement in the instructions for use, this standard does not include

requirements and test provisions for the manufacturers of the product, or recommendations to

the users of the product for environmental improvement. However, all parties intervening in its

design, manufacture, packaging, distribution, use, maintenance, repair, reuse, recovery and

disposal are invited to take account of environmental considerations.
---------------------- Page: 13 ----------------------
SIST EN 60832-2:2010
– 8 – 60832-2 © IEC:2010
LIVE WORKING – INSULATING STICKS
AND ATTACHABLE DEVICES –
Part 2: Attachable devices
1 Scope

This part of IEC 60832 gives the essential requirements for devices that can be attached onto

and removed from the fitting of the insulating sticks for live working, for use on a.c. electrical

installations.
Part 1 of IEC 60832 covers insulating sticks.

In this part of the standard, the term “device” is used for “attachable device”, unless otherwise

specified.

Products designed and manufactured according to this standard contribute to the safety of the

users provided they are used by skilled persons, in accordance with safe methods of work

and the instructions for use.
2 Normative references

The following normative documents contain provisions which, through reference in this text,

constitute provisions of this international standard. For dated references, only the edition cited

applies. For undated references, the latest edition of the referenced document (including any

amendments) applies.
IEC 60060-1, High-voltage test techniques – Part 1: General definitions and test
requirements

IEC 60212:1971, Standard conditions for use prior to and during the testing of solid electrical

insulating materials
IEC 60417, Graphical symbols for use on equipment

IEC 61318:2007, Live working – Conformity assessment applicable to tools, devices and

equipment

IEC 61477, Live working – Minimum requirements for the utilization of tools, devices and

equipment
3 Terms, definitions and symbols
3.1 Terms and definitions

For the purposes of this document, the terms and definitions given in IEC 61318 and the

following apply.
---------------------- Page: 14 ----------------------
SIST EN 60832-2:2010
60832-2 © IEC:2010 – 9 –
3.1.1
rated value

value of a quantity used for specification purposes, established for a specified set of operating

conditions of a component, device, equipment or system
[IEV 151-16-08]
3.1.2
type of device

family of devices which are of the same design and application and are of similar dimensions

3.2 Symbols

T rated torque given by the manufacturer for a given device and for testing purposes

rated tensile force given by the manufacturer for a given device and for testing
purposes
rated compression force given by the manufacturer for a given device and for
testing purposes
rated bending force given by the manufacturer for a given device and for testing
purposes
4 Requirements
4.1 General

The following requirements have been prepared in order that the products covered by this

standard are desig
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.