EN 62586-1:2014

Power quality measurement in power supply systems - Part 1: Power quality instruments (PQI)

IEC 62586-1:2013 specifies product and performance requirements for instruments whose functions include measuring, recording and possibly monitoring power quality parameters in power supply systems, and whose measuring methods (class A or class S) are defined in IEC 61000-4-30. These requirements are applicable in single, dual- (split phase) and 3-phase a.c. power supply systems at 50 Hz or 60 Hz. These instruments can be used in the generation, transmission and distribution of electricity, for example inside a power station, substation or a distributed generator connection and at the interface point between the installation and the network, e.g. in order to check the compliance of the connection agreement between a network operator and the customer. These instruments are fixed-installed or portable. They are intended to be used indoors and/or outdoors. Devices such as digital fault recorders, energy/power meters, protection relays or circuit breakers may include power quality functions defined in 61000-4-30 class A or class S. If such devices are specified according to this standard, then this standard fully applies and applies in addition to the relevant product standard. This standard does not replace the relevant product standard.

Messung der Spannungsqualität in Energieversorgungssystemen - Teil 1: Messgeräte für die Spannungsqualität

Mesure de la qualité de l'alimentation dans les réseaux d'alimentation - Partie 1: Instruments de mesure de la qualité de l'alimentation

L'IEC 62586-1:2013 spécifie les exigences produits et de performances pour les instruments dont les fonctions incluent la mesure, l'enregistrement et éventuellement la surveillance des paramètres de la qualité des réseaux d'alimentation, dont les méthodes de mesure (classe A ou classe S) sont définies dans la IEC 61000-4-30. Ces exigences sont applicables aux réseaux d'alimentation simple, double- (phase divisée) et triphasée c.a. à 50 Hz ou 60 Hz. Les instruments suivants peuvent être utilisés dans la génération, la transmission et la distribution de l'électricité, ou au point d'interface entre l'installation et le réseau. Ces instruments sont installés de façon fixe ou sont portables. Ils sont destinés à un usage intérieur et/ou extérieur. Les appareils tels que les enregistreurs de défauts numériques, les compteurs d'énergie/puissance, les relais de protection ou les disjoncteurs peuvent inclure des fonctions de qualité de l'alimentation définies dans 61000-4-30 classe A ou classe S. Si ces appareils sont spécifiés conformément à cette norme, cette dernière s'applique entièrement et s'applique en supplément à la norme de produit pertinente. La présente norme ne remplace pas la norme de produit pertinente.

Merjenje kakovosti električne energije v napajalnih sistemih - 1. del: Instrumenti za kakovost napajanja (PQI) (IEC 62586-1:2013)

Standard EN IEC 62586-1 določa zahteve za izdelek in delovanje za instrumente, katerih funkcije zajemajo merjenje, beleženje in morebitno nadzorovanje parametrov kakovosti električne energije v napajalnih sistemih ter katerih merilne metode (razred A ali razred S) so določene v standardu IEC 61000-4-30. Te zahteve se uporabljajo v enofaznih, dvofaznih (razdeljena faza) in trifaznih izmeničnih napajalnih sistemih pri 50 Hz ali 60 Hz. Te instrumente je mogoče uporabljati: – pri proizvodnji, prenosu in distribuciji električne energije, na primer v elektrarni, razdelilni postaji ali priključku distribuiranega generatorja; – v točki vmesnika med obratom in omrežjem, npr. da se preveri skladnost dogovora o priključku med upravljavcem omrežja in stranko. Naprave, kot so digitalni snemalniki okvar, merilniki energije/moči, zaščitni releji ali odklopniki, lahko vključujejo funkcije kakovosti napajanja, opredeljene v standardu 61000-4-30, razred A ali razred S. Če so take naprave opredeljene v skladu s tem standardom, ta standard velja v celoti in se uporablja kot dodatek k ustreznemu standardu za proizvod. Ta standard ne nadomešča ustreznega standarda za proizvod.

General Information

• Status: Withdrawn
• Publication Date: 19-Jun-2014
• Withdrawal Date: 15-Jan-2017
• ICS: 17.220.20 - Measurement of electrical and magnetic quantities
• Technical Committee: CLC/TC 85X - Measuring equipment for electrical and electromagnetic quantities
• Drafting Committee: IEC/TC 85 - IEC_TC_85
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 10-Nov-2020
• Completion Date: 10-Nov-2020
• Directive: 2004/108/EC - Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
• Directive: 2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/30/EU - Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Ref Project: SIST EN 62586-1:2014 - Power quality measurement in power supply systems - Part 1: Power Quality Instruments (PQI) (IEC 62586-1:2013)

Relations

• Replaced By: EN 62586-1:2017 - Power quality measurement in power supply systems - Part 1: Power quality instruments (PQI)
• Effective Date: 13-Nov-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2014
0HUMHQMHNDNRYRVWLHOHNWULþQHHQHUJLMHYQDSDMDOQLKVLVWHPLKGHO,QVWUXPHQWL]D
NDNRYRVWQDSDMDQMD34,,(&
Power quality measurement in power supply systems - Part 1: Power Quality Instruments
(PQI) (IEC 62586-1:2013)
Messung der Spannungsqualität in Energieversorgungssystemen -Teil 1: Messgeräte für
die Spannungsqualität (IEC 62586-1:2013)
Mesure de la qualité de l'alimentation dans les réseaux d'alimentation - Partie 1:
Instruments de mesure de la qualité de l'alimentation (CIE 62586-1:2013)
Ta slovenski standard je istoveten z: EN 62586-1:2014
ICS:
17.220.20 0HUMHQMHHOHNWULþQLKLQ Measurement of electrical
PDJQHWQLKYHOLþLQ and magnetic quantities
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 62586-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2014
ICS 17.220.20
English Version
Power quality measurement in power supply systems - Part 1:
Power quality instruments (PQI)
(IEC 62586-1:2013)
Mesure de la qualité de l'alimentation dans les réseaux Messung der Spannungsqualität in
d'alimentation - Partie 1: Instruments de mesure de la Energieversorgungssystemen - Teil 1: Messgeräte für die
qualité de l'alimentation Spannungsqualität
(CEI 62586-1:2013) (IEC 62586-1:2013)
This European Standard was approved by CENELEC on 2014-01-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62586-1:2014 E
Foreword
The text of document 85/460/FDIS, future edition 1 of IEC 62586-1, prepared by IEC/TC 85
"Measuring equipment for electrical and electromagnetic quantities" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 62586-1:2014.

The following dates are fixed:
(dop) 2014-12-20
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2017-01-16
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive.

For the relationship with EU Directive see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 62586-1:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60359 NOTE Harmonized as EN 60359.
IEC 61010 Series NOTE Harmonized as EN 61010 Series (partly modified).

- 3 - EN 62586-1:2014
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu
Publication Year Title EN/HD Year

IEC 60068-1 -  Environmental testing - EN 60068-1 -
Part 1: General and guidance
IEC 60068-2-1 -  Environmental testing - EN 60068-2-1 -
Part 2-1: Tests - Test A: Cold
IEC 60068-2-2 -  Environmental testing - EN 60068-2-2 -
Part 2-2: Tests - Test B: Dry heat
IEC 60068-2-6 -  Environmental testing - EN 60068-2-6 -
Part 2-6: Tests - Test Fc: Vibration
(sinusoidal)
IEC 60068-2-14 -  Environmental testing - EN 60068-2-14 -
Part 2-14: Tests - Test N: Change of
temperature
IEC 60068-2-27 -  Environmental testing - EN 60068-2-27 -
Part 2-27: Tests - Test Ea and guidance:
Shock
IEC 60068-2-31 -  Environmental testing - EN 60068-2-31 -
Part 2-31: Tests - Test Ec: Rough
handling shocks, primarily for equipment-
type specimens
IEC 60068-2-52 -  Environmental testing - EN 60068-2-52 -
Part 2-52: Tests - Test Kb: Salt mist,
cyclic (sodium chloride solution)
Environmental testing -
IEC 60068-2-57 -  EN 60068-2-57 -
Part 2-57: Tests - Test Ff: Vibration -
Time-history and sine-beat method
IEC 60068-2-78 -  Environmental testing - EN 60068-2-78 -
Part 2-78: Tests - Test Cab: Damp heat,
steady state
IEC 60529 -  Degrees of protection provided by EN 60529 -
enclosures (IP Code)
IEC 60654-1 -  Industrial-process measurement and EN 60654-1 -
control equipment - Operating
conditions -
Part 1: Climatic conditions
Publication Year Title EN/HD Year

IEC 60664-1 2007 Insulation coordination for equipment EN 60664-1 2007
within low-voltage systems -
Part 1: Principles, requirements and tests
IEC 60721-3-1 -  Classification of environmental EN 60721-3-1 -
conditions -
Part 3: Classification of groups
of environmental parameters
and their severities -
Section 1: Storage
IEC 60721-3-2 -  Classification of environmental EN 60721-3-2 -
conditions -
Part 3: Classification of groups of
environmental parameters and their
severities -
Section 2: Transportation
IEC 60721-3-3 -  Classification of environmental EN 60721-3-3 -
conditions -
Part 3: Classification of groups of
environmental parameters and their
severities -
Section 3: Stationary use at
weatherprotected locations
IEC 61000-4-7 2002 Electromagnetic compatibility (EMC) - EN 61000-4-7 2002
+A1 2008 Part 4-7: Testing and measurement +A1 2009
techniques - General guide on harmonics
and interharmonics measurements and
instrumentation, for power supply
systems and equipment connected
thereto
IEC 61000-4-15 2010 Electromagnetic compatibility (EMC) - EN 61000-4-15 2011
Part 4-15: Testing and measurement
techniques - Flickermeter - Functional
and design specifications
IEC 61000-4-30 2008 Electromagnetic compatibility (EMC) - EN 61000-4-30 2009
Part 4-30 : Testing and measurement
techniques - Power quality measurement
methods
IEC/TS 61000-6-5 -  Electromagnetic compatibilty (EMC) - - -
Part 6-5: Generic standards - Immunity
for power station and substation
environments
IEC 61010-1 2010 Safety requirements for electrical EN 61010-1 2010
equipment for measurement, control
and laboratory use -
Part 1: General requirements
IEC 61010-2-030 -  Safety requirements for electrical EN 61010-2-030 -
equipment for measurement, control
and laboratory use -
Part 2-030: Particular requirements for
testing and measuring circuits

- 5 - EN 62586-1:2014
Publication Year Title EN/HD Year

IEC 62262 -  Degrees of protection provided by EN 62262 -
enclosures for electrical equipment
against external mechanical impacts
(IK code)
IEC 62586-2 -  Power quality measurement in power EN 62586-2 -
supply systems -
Part 2: Functional tests and uncertainty
requirements
CISPR 22 -  Information technology equipment - EN 55022 -
Radio disturbance characteristics - Limits
and methods of measurement
Annex ZZ
(informative)
Coverage of Essential Requirements of EU Directives

This European Standard has been prepared under a mandate given to CENELEC by the
European Commission and the European Free Trade Association and within its scope the
standard covers protection requirements of Annex I Article 1 of the EU Directive 2004/108/EC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling
within the scope of this standard.

IEC 62586-1 ®
Edition 1.0 2013-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Power quality measurement in power supply systems –

Part 1: Power quality instruments (PQI)

Mesure de la qualité de l'alimentation dans les réseaux d'alimentation –

Partie 1: Instruments de mesure de la qualité de l'alimentation

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX V
ICS 17.220.20 ISBN 978-2-8322-1290-5

– 2 – 62586-1 © IEC:2013
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, abbreviations, notations and symbols . 9
3.1 General definitions . 9
3.2 Terms and definitions related to environments. 10
3.3 Definitions related to uncertainty . 10
3.4 Notations . 11
3.4.1 Functions . 11
3.4.2 Symbols and abbreviations . 11
3.4.3 Indices . 12
4 Environmental conditions . 12
4.1 General . 12
4.2 Environments FI1, FI2, FI1-H, FI2-H, FO and FO-H . 13
4.3 Environments PI, PI-H, PO and PO-H . 14
4.4 Relationship between ambient air temperature and relative humidity . 15
5 Ratings . 15
5.1 Rated input energising voltages . 15
5.2 Rated frequencies . 15
6 Design and construction . 15
6.1 General . 15
6.2 General architecture . 15
6.3 Functions embedded in PQI-A and PQI-S . 16
6.3.1 PQI-A minimum functions definition . 16
6.3.2 PQI-S minimum functions definition . 17
6.3.3 Summary of IEC 61000-4-30 requirements for functions . 17
6.4 Additional requirements complementary to IEC 61000-4-30 . 18
6.4.1 Data to be provided for testing reasons . 18
6.4.2 Resolution of the presented data . 20
6.4.3 Clarificati
...