prEN IEC 63562:2026
(Main)Germicidal equipment - Low-pressure mercury UV radiation sources for germicidal purpose - Safety
- Status
- Not Published
- Publication Date
- 09-Mar-2028
- Technical Committee
- CLC/TC 34 - 'Lamps and related equipment
- Current Stage
- 4020 - Enquiry circulated - Enquiry
- Start Date
- 02-Oct-2026
- Due Date
- 31-Mar-2026
- Completion Date
- 02-Oct-2026
prEN IEC 63562:2026 is a CLC draft standard for the safety of low-pressure mercury UV radiation sources for germicidal purpose. It specifies safety requirements for these low-pressure mercury UV radiation sources, including classification, marking, electrical, thermal, mechanical and photobiological safety, for manufacturers, luminaire designers, test labs and buyers who need to verify that a source is suitable for germicidal use.
What does prEN IEC 63562:2026 specify?
prEN IEC 63562:2026 specifies the safety requirements of low-pressure mercury UV radiation sources for germicidal purposes. The document covers the source itself and organizes the requirements into scope, normative references, terms and definitions, classification, general conditions, marking, electrical safety, thermal safety, mechanical safety, actinic UV hazard, ozone generation, resistance to UV radiation and ozone exposure, and other safety requirements.
The document is structured so that general requirements apply to all categories unless a later clause says otherwise. Annex A links the new requirements to clauses in existing lamp safety standards, and Annex B gives information for luminaire design.
What are the key requirements of prEN IEC 63562:2026?
prEN IEC 63562:2026 sets different safety expectations depending on whether the source is Category A, B or C. That matters in practice because the cap style, installation method and test route change the compliance work a manufacturer has to do.
Classification and test conditions
- Clause 4 classifies low-pressure mercury UV sources as Category A, B or C based on the cap arrangement. Category A uses caps covered by IEC 60968, IEC 61195 or IEC 61199, Category B uses other caps, and Category C has no cap.
- Clause 5 says the document uses type tests. This means compliance is checked on representative samples, not on every production item, so manufacturers still need production control and routine testing.
Marking and product information
- Clause 6 requires key marking on the source itself, including origin, nominal power, rated power, UV hazard warnings, rated voltage, rated frequency and product type where applicable.
- Other information goes on the package, instructions or data sheets, including risk group, installation guidance, ozone warnings, dimensional data, cap information, maximum cap temperature, mass and bending moment, controlgear information and rated lifetime.
- Clause 6.4 checks marking by visual inspection and by a rubbing test with a water-soaked cloth. In practice, the marking has to stay readable through handling and cleaning.
Electrical safety
- Clause 7 applies electrical safety requirements to Categories A and B, but not to Category C.
- Category A sources follow the relevant self-ballasted or lamp-safety provisions from IEC 60968, IEC 61195 or IEC 61199.
- Category B sources with non-standardized caps need a risk analysis for protection against electric shock, and hazardous live parts must not be reachable with the source installed, being inserted, or removed. This is checked with inspection and probe testing using IEC 61032 Test probe B.
Thermal and mechanical safety
- Clauses 8 and 9 control cap temperature rise, resistance to heat and flame, cap construction, adhesive strength, axial strength, mass, bending moment and source dimensions.
- For Category B sources, declared limits for pull, bend or torque, mass and bending moment must be met and are checked by measurement and by tests after heat exposure. For Category C sources with insulated lead wire, the wire thermal class and flame resistance are checked instead of cap-related requirements.
Photobiological and environmental hazards
- Clause 10 limits the actinic UV hazard risk group at a 200 mm assessment distance, using measurement according to IEC 62471.
- Clause 11 covers ozone generation. Sources declared ozone free, or not marked with ozone warnings, must not generate hazardous ozone levels.
- Clause 12 checks resistance of materials to UV-C and, where relevant, ozone. This matters because the source materials themselves must survive the declared lifetime and exposure conditions.
Other safety requirements
- Clause 13 ties certain safety aspects back to existing standards for radio interference suppression capacitors, fault conditions, end of life and abnormal operation. Annex A shows which clause in the existing standards corresponds to each case.
What terms does prEN IEC 63562:2026 define?
prEN IEC 63562:2026 uses a small set of terms that are central to the document.
- LPM UV source - a UV radiation source from low-pressure mercury discharge that emits either 254 nm radiation or 185 nm and 254 nm radiation.
- Category A - a source with cap(s) specified in IEC 60968, IEC 61195 or IEC 61199.
- Category B - a source with cap(s) not covered by Category A.
- Category C - a source without a cap.
- Actinic UV hazard - the skin and eye hazard evaluated over 200 nm to 400 nm.
- External controlgear - the designated controlgear used when the source does not operate on its own internal gear.
- Self-ballasted LPM UV source - a source that includes its own controlgear-related functionality, as used in the document’s electrical and marking provisions.
Who uses prEN IEC 63562:2026?
prEN IEC 63562:2026 is used by manufacturers of germicidal UV sources, lamp and luminaire designers, test laboratories, conformity assessment bodies and quality managers. It is also relevant to purchasers and specifiers who need to compare source type, cap type, hazard marking and declared limits before approving a product for germicidal equipment. The document is tied to lighting and sterilizing-equipment work, especially where UV safety, ozone and material durability have to be checked before release.
What changed in prEN IEC 63562:2026 from the previous edition?
prEN IEC 63562:2026 supersedes 34/1418/CD and 34/1471/CC.
Which standards are used with prEN IEC 63562:2026?
prEN IEC 63562:2026 uses several companion standards for caps, test methods and safety checks.
- IEC 60061-1, IEC 60061-2, IEC 60061-4 - cap, holder and gauge information, including interchangeability and safety.
- IEC 60085 - thermal evaluation and designation of electrical insulation.
- IEC 60243 - electrical strength test methods for insulating materials.
- IEC 60968:2015 - safety requirements for self-ballasted fluorescent lamps, reused for several test and safety provisions.
- IEC 61032:1997 - test probes for checking accessibility of hazardous live parts.
- IEC 61195:2014 and IEC 61199:2014 - safety specifications for double-capped and single-capped fluorescent lamps.
- IEC 62471:2006 and IEC 62471-6:2022 - photobiological safety and UV lamp product assessment.
- IEC 63561 - ozone production measurement from UV-C radiation sources and luminaires.
- ISO 178, ISO 527 (all parts) and ISO 1431-1 - mechanical property and ozone-cracking tests used in material exposure checks.
- IEC 60050-845 - terminology source for terms and definitions.
What does the prEN IEC 63562:2026 document contain?
The document contains a marking table, two correspondence tables in Annex A, and an informative Annex B for luminaire design. It also includes figures for UV warning symbols and clause-by-clause test methods for marking durability, electric shock protection, insulation resistance, electric strength, cap temperature rise, mechanical strength, actinic UV hazard, ozone generation, and resistance to UV-C and ozone exposure. For a reader, the key value is that it tells you what to declare, what to test, and which existing lamp standards to reuse for each category of source.
Frequently Asked Questions
prEN IEC 63562:2026 is a draft published by CLC. Its full title is "Germicidal equipment - Low-pressure mercury UV radiation sources for germicidal purpose - Safety". This standard covers: Germicidal equipment - Low-pressure mercury UV radiation sources for germicidal purpose - Safety
Germicidal equipment - Low-pressure mercury UV radiation sources for germicidal purpose - Safety
prEN IEC 63562:2026 is associated with the following European legislation: EU Directives/Regulations: 2014/35/EU; Standardization Mandates: M/511. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
prEN IEC 63562:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2026
Germicidna oprema - Nizkotlačni živosrebrni viri UV-sevanja za germicidne
namene – Varnost
Germicidal equipment - Low-pressure mercury UV radiation sources for germicidal
purpose - Safety
Équipement germicide - Sources de rayonnement UV au mercure à basse pression
destinées à un usage germicide - Sécurité
Ta slovenski standard je istoveten z: prEN IEC 63562:2026
ICS:
11.080.10 Sterilizacijska oprema Sterilizing equipment
29.140.01 Žarnice na splošno Lamps in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
34/1495/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 63562 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2026-10-02 2026-12-25
SUPERSEDES DOCUMENTS:
34/1418/CD, 34/1471/CC
IEC TC 34 : LIGHTING
SECRETARIAT: SECRETARY:
United Kingdom Mr Petar Luzajic
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
ASPECTS CONCERNED:
Safety
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Germicidal equipment - Low-pressure mercury UV radiation sources for germicidal purpose -
Safety
PROPOSED STABILITY DATE: 2030
NOTE FROM TC/SC OFFICERS:
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National
Committee positions. You may not copy or "mirror" the file or printed version of the document, o r any part of it, for
any other purpose without permission in writing from IEC.
IEC CDV 63562 © IEC 2026
1 CONTENTS
3 FOREWORD . 3
4 INTRODUCTION . 5
5 1 Scope . 6
6 2 Normative references . 6
7 3 Terms and definitions . 6
8 4 Classification . 7
9 5 General . 7
10 5.1 General requirement . 7
11 5.2 General conditions for tests . 7
12 5.2.1 Type test . 7
13 5.2.2 Test samples . 7
14 5.2.3 Compliance by inspection of relevant data . 7
15 5.2.4 External controlgear . 7
16 6 Marking . 8
17 6.1 Overview. 8
18 6.2 Marking content . 9
19 6.3 LPM UV source marking . 10
20 6.4 Durability and legibility of marking . 11
21 7 Electrical safety . 11
22 7.1 General . 11
23 7.2 Protection against electric shock . 11
24 7.2.1 Category A LPM UV sources . 11
25 7.2.2 Category B LPM UV sources . 11
26 7.3 Insulation resistance . 11
27 7.4 Electric strength . 11
28 7.4.1 Creepage distance and clearance . 11
29 7.4.2 Category A LPM UV sources . 11
30 7.4.3 Category B LPM UV sources . 11
31 8 Thermal safety . 12
32 8.1 Category A LPM UV sources . 12
33 8.2 Category B LPM UV sources . 12
34 8.2.1 Cap temperature rise . 12
35 8.2.2 Resistance to heat . 12
36 8.2.3 Resistance to flame and ignition . 12
37 8.3 Category C UV LPM sources. 12
38 8.3.1 Resistance to heat . 12
39 8.3.2 Resistance to flame and ignition . 12
40 9 Mechanical safety . 12
41 9.1 Mechanical requirements for caps . 12
42 9.1.1 Category A LPM UV sources . 12
43 9.1.2 Category B LPM UV sources . 12
44 9.2 Mechanical requirements for Category C LPM UV sources . 13
45 9.3 Source mass and bending moment imparted by the source at the lampholder . 13
46 9.3.1 Category A LPM UV sources . 13
IEC CDV 63562 © IEC 2026
47 9.3.2 Category B and category C LPM UV sources . 13
48 9.4 Source Dimension of category A and category B LPM UV sources . 13
49 10 Actinic UV hazard . 13
50 11 Ozone generation . 14
51 12 Resistance to UV radiation and ozone exposure . 14
52 12.1 General . 14
53 12.2 Exposure to UV-C radiation . 14
54 12.3 Exposure to ozone . 14
55 13 Other safety requirements . 14
56 Annex A (normative) Corresponding clauses in existing standard for safety
57 requirements . 15
58 Annex B (Informative) Information for luminaire design . 17
59 B.1 General . 17
60 B.2 Water contact . 17
61 B.3 Protection of against potential hazards . 17
IEC CDV 63562 © IEC 2026
65 INTERNATIONAL ELECTROTECHNICAL COMMISSION
66 ____________
68 GERMICIDAL EQUIPMENT — LOW-PRESSURE MERCURY UV RADIATION
69 SOURCES FOR GERMICIDAL PURPOSE — SAFETY
72 FOREWORD
73 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
74 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
75 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
76 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
77 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
78 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
79 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
80 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
81 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
82 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
83 consensus of opinion on the relevant subjects since each technical committee has representation from all
84 interested IEC National Committees.
85 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
86 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
87 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
88 misinterpretation by any end user.
89 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
90 transparently to the maximum extent possible in their national and regional publications. Any divergence between
91 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
92 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
93 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
94 services carried out by independent certification bodies.
95 6) All users should ensure that they have the latest edition of this publication.
96 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
97 members of its technical committees and IEC National Committees for any personal injury, property damage or
98 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
99 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
100 Publications.
101 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
102 indispensable for the correct application of this publication.
103 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
104 rights. IEC shall not be held responsible for identifying any or all such patent rights.
105 IEC 6XXXX has been prepared by IEC technical committee 34: Lighting. It is an International
106 Standard.
107 The text of this International Standard is based on the following documents:
Draft Report on voting
XX/XX/FDIS XX/XX/RVD
109 Full information on the voting for its approval can be found in the report on voting indicated in
110 the above table.
111 The language used for the development of this International Standard is English.
112 This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
113 accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
114 at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
115 described in greater detail at www.iec.ch/publications.
IEC CDV 63562 © IEC 2026
116 The committee has decided that the contents of this document will remain unchanged until the
117 stability date indicated on the IEC website under webstore.iec.ch in the data related to the
118 specific document. At this date, the document will be
119 • reconfirmed,
120 • withdrawn,
121 • replaced by a revised edition, or
122 • amended.
IEC CDV 63562 © IEC 2026
124 INTRODUCTION
125 This document acknowledges the need for safety specifications for low-pressure mercury UV
126 radiation sources for germicidal purpose, which mainly generate single-line spectrum radiation
127 of 254 nm or dual-line spectrum radiation of 185 nm and 254 nm.
128 This document was prepared by referencing, wherever possible, the existing standards for
129 similar types of discharge lamps used in general lighting: IEC 61195:2014, IEC 61199:2014 and
130 IEC 60968:2015. Additional or deviated requirements for germicidal UV sources are specified
131 wherever necessary.
132 The provisions in this document represent the technical knowledge of experts from the field of
133 the UV radiation for germicidal purpose, and are developed in close context with the safety of
134 other type of UV radiation sources for germicidal purpose, e.g., excimer sources.
IEC CDV 63562 © IEC 2026
136 GERMICIDAL EQUIPMENT — LOW-PRESSURE MERCURY UV RADIATION
137 SOURCES FOR GERMICIDAL PURPOSE — SAFETY
139 1 Scope
140 This document specifies the safety requirements of low-pressure mercury UV radiation sources
141 for germicidal purposes.
142 2 Normative references
143 The following documents are referred to in the text in such a way that some or all of their content
144 constitutes requirements of this document. For dated references, only the edition cited applies.
145 For undated references, the latest edition of the referenced document (including any
146 amendments) applies.
147 IEC 60061-1, Lamp caps and holders together with gauges for the control of interchangeability
148 and safety - Part 1: Lamp caps
149 IEC 60061-2, Lamp caps and holders together with gauges for the control of interchangeability
150 and safety - Part 2: Lampholders
151 IEC 60061-4, Lamp caps and holders together with gauges for the control of interchangeability
152 and safety – Part 4: Guidelines and general information
153 IEC 60085, Electrical insulation – Thermal evaluation and designation
154 IEC 60243, Electrical strength of insulating materials – Test methods
155 IEC 60968:2015, Self-ballasted fluorescent lamps for general lighting services - Safety
156 requirements
157 IEC 61032:1997: Protection of persons and equipment by enclosures - Probes for verification
158 IEC 61195:2014, Double-capped fluorescent lamps – Safety specifications
159 IEC 61199:2014, Single-capped fluorescent lamps – Safety specifications
160 IEC 62471:2006, Photobiological safety of lamps and lamp systems
161 IEC 62471-6:2022, Photobiological safety of lamps and lamp systems - Part 6: Ultraviolet lamp
162 products
163 IEC 63561, Measurement of ozone production from UV-C radiation sources and luminaires
164 ISO 178, Plastics - Determination of flexural properties
165 ISO 527 (all parts), Plastics - Determination of tensile properties
166 ISO 1431-1, Rubber, vulcanized or thermoplastic – Resistance to ozone cracking – Part 1:
167 Static and dynamic strain testing
168 3 Terms and definitions
169 For the purposes of this document, the terms and definitions given in IEC 60050 -845 and the
170 following apply.
171 ISO and IEC maintain terminology databases for use in standardization at the following
172 addresses:
173 • IEC Electropedia: available at https://www.electropedia.org/
IEC 63561 is under preparation.
IEC CDV 63562 © IEC 2026
174 • ISO Online browsing platform: available at https://www.iso.org/obp
175 3.1
176 LPM UV source
177 UV radiation source which emits either a single-line spectrum at 254 nm or dual-line spectrum
178 at 185 nm and 254 nm from a low-pressure mercury gaseous discharge
179 Note 1 to entry: An LPM UV source can have hot cathodes or cold cathodes, and is incorporated with suitable high
180 UV transmittance glass without phosphor coating.
181 Note 2 to entry: An LPM UV lamp is an LPM UV source with at least one cap.
182 4 Classification
183 The LPM UV sources shall be classified as follows.
184 – Category A: LPM UV sources with cap(s) specified in IEC 60968, IEC 61195 or IEC 61199,
185 – Category B: LPM UV sources with cap(s) not covered by category A,
186 – Category C: LPM UV sources without a cap.
187 NOTE 1 LPM UV sources with a hot-cathode normally have caps.
188 NOTE 2 Category A LPM UV sources can have lamp dimensions that are different from those specified in the
189 datasheets of existing standards for fluorescent lamp performance.
190 NOTE 3 Category B LPM UV sources can have the cap(s) specified in IEC 60061-1.
191 5 General
192 5.1 General requirement
193 Unless specifically indicated in following clauses, the safety requirements are applicable to all
194 categories of LPM UV sources.
195 Information for luminaire design is given in Annex C.
196 5.2 General conditions for tests
197 5.2.1 Type test
198 Tests according to this document are type tests.
199 NOTE The requirements and tolerances specified in this document are related to testing of a type test sample
200 submitted by the manufacturer for that purpose. Compliance of type test samples does not ensure compliance of the
201 whole production of a manufacturer with this document. Conformity of production is the responsibility of the
202 manufacturer and routine tests and quality insurance in addition to the type test can be necessary.
203 5.2.2 Test samples
204 Unless otherwise specified, the type test shall be carried out on one sample consisting of one
205 or more items submitted for the purpose of the type test.
206 Where there is a range of similar LPM UV sources for testing, samples representing the most
207 onerous case within the range shall be selected as relevant to the test criteria.
208 NOTE For example, damage to marking as a result of the marking test has no impact on electrical testing, thus
209 the LPM UV source is still considered to be representative of production for other tests.
210 If the source is provided with a cap that is not specified in IEC 60061-1, a sample of the
211 associated lampholder shall be provided for the test.
212 5.2.3 Compliance by inspection of r
...



