Electric vehicle conductive charging system - Part 3-2: DC EV supply equipment where protection relies on double or reinforced insulation - Particular requirements for portable and mobile equipment

This part of IEC 61851-3 series (in a first step as Technical Specification for three-year period) together with part 1 of IEC61851-3, applies to the d.c. power supply equipment (e.g. VCU) for the conductive transfer of electric power between the supply network and an light electric road vehicle when connected to the supply network , with a rated supply voltage up to 480 V a.c. or up to 400 V d.c. and a rated ìoutputî voltage up to 480 V a.c. or up to 200 V d.c. The supply systems described in the IEC 61851-3 series are primarily intended for the use by EVs of category L hereinafter referred to as light electric vehicles (light EVs). NOTE 1 Light EV includes all electrically propelled two and three wheeled vehicles of Category L1 up to Category L7 according to the definition of ECE-TRANS-WP29-78r2e and all electrically propelled or assisted cycles. The electrical protection of the complete light EV supply system from the connection to the supply network up to the light EV or removed RESS complies with protective separation and with galvanic separation between a.c. input and d.c. output or class III.

Konduktive Ladesysteme für Elektrofahrzeuge - Teil 3-2: Gleichstrom-Versorgungseinrichtungen für Elektrofahrzeuge mit Schutzwirkung durch doppelte oder verstärkte Isolierung - Besondere Anforderungen für tragbare und ortsveränderliche Betriebsmittel

Système de charge conductive pour véhicules électriques - Partie 3-2 : Exigences relatives aux véhicules électriques légers - Matériel de charge conductive en courant continu

Sistemi za napajanje električnih vozil - 3-2. del: Oprema za napajanje električnih vozil z enosmernim tokom, kjer varnost zagotavlja dvojna ali ojačena izolacija - Posebne zahteve za prenosno in mobilno opremo (IEC/TS 61851-3-2:2023)

Ta del skupine standardov IEC 61851-3 (v prvem koraku kot tehnične specifikacije za triletno obdobje) skupaj s 1. delom standarda IEC 61851-3 se uporablja za opremo za napajanje z enosmernim tokom (npr. VCU) za konduktivni prenos električne energije med električnim omrežjem in lahkim električnim cestnim vozilom, ko je to priključeno na električno omrežje z nazivno izmenično napetostjo napajanja do 480 V ali enosmerno napetostjo do 400 V in nazivno izhodno izmenično napetostjo do 480 V oziroma izhodno enosmerno napetostjo do 200 V.
Napajalni sistemi, opisani v skupini standardov IEC 61851-3, so namenjeni predvsem uporabi električnih vozil kategorije L, v nadaljevanju lahka električna vozila.
OPOMBA 1: Lahko električno vozilo pomeni vsa dvo- in trikolesna vozila na električni pogon kategorij L1 do vključno L7 v skladu z definicijo ECE-TRANS-WP29-78r2e in vsa kolesa na električni pogon in kolesa s pomožnim motorjem.
Električna zaščita celotnega napajalnega sistema lahkega električnega vozila od priključka na električno omrežje do lahkega električnega vozila ali odstranjenega sistema za shranjevanja energije z možnostjo ponovnega polnjenja je skladna z zaščitno ločitvijo in z galvansko ločitvijo med vhodnim izmeničnim tokom in izhodnim enosmernim tokom oziroma opremo razreda III.

General Information

Status
Published
Publication Date
21-Dec-2023
Current Stage
6060 - Document made available - Publishing
Start Date
22-Dec-2023
Completion Date
22-Dec-2023

Buy Standard

Technical specification
TS CLC IEC/TS 61851-3-2:2024
English language
38 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2024
Sistemi za napajanje električnih vozil - 3-2. del: Oprema za napajanje električnih
vozil z enosmernim tokom, kjer varnost zagotavlja dvojna ali ojačena izolacija -
Posebne zahteve za prenosno in mobilno opremo (IEC/TS 61851-3-2:2023)
Electric vehicle conductive charging system - Part 3-2: DC EV supply equipment where
protection relies on double or reinforced insulation - Particular requirements for portable
and mobile equipment (IEC/TS 61851-3-2:2023)
Konduktive Ladesysteme für Elektrofahrzeuge - Teil 3-2: Gleichstrom-
Versorgungseinrichtungen für Elektrofahrzeuge mit Schutzwirkung durch doppelte oder
verstärkte Isolierung - Besondere Anforderungen für tragbare und ortsveränderliche
Betriebsmittel (IEC/TS 61851-3-2:2023)
Système de charge conductive pour véhicules électriques - Partie 3-2 : Exigences
relatives aux véhicules électriques légers - Matériel de charge conductive en courant
continu (IEC/TS 61851-3-2:2023)
Ta slovenski standard je istoveten z: CLC IEC/TS 61851-3-2:2023
ICS:
43.120 Električna cestna vozila Electric road vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION CLC IEC/TS 61851-3-2

SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION December 2023
ICS 43.120
English Version
Electric vehicle conductive charging system - Part 3-2: DC EV
supply equipment where protection relies on double or reinforced
insulation - Particular requirements for portable and mobile
equipment
(IEC/TS 61851-3-2:2023)
Système de charge conductive pour véhicules électriques - Konduktive Ladesysteme für Elektrofahrzeuge - Teil 3-2:
Partie 3-2 : Exigences relatives aux véhicules électriques Gleichstrom-Versorgungseinrichtungen für
légers - Matériel de charge conductive en courant continu Elektrofahrzeuge mit Schutzwirkung durch doppelte oder
(IEC/TS 61851-3-2:2023) verstärkte Isolierung - Besondere Anforderungen für
tragbare und ortsveränderliche Betriebsmittel
(IEC/TS 61851-3-2:2023)
This Technical Specification was approved by CENELEC on 2023-12-04.

CENELEC members are required to announce the existence of this TS in the same way as for an EN and to make the TS available promptly
at national level in an appropriate form. It is permissible to keep conflicting national standards in force.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. CLC IEC/TS 61851-3-2:2023 E

European foreword
This document (CLC IEC/TS 61851-3-2:2023) consists of the text of IEC/TS 61851-3-2:2023,
prepared by IEC/TC 69 "Electrical power/energy transfer systems for electrically propelled road
vehicles and industrial trucks”.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CENELEC by the
European Commission. The Standing Committee of the EFTA States subsequently approves these
requests for its Member States.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Technical Specification IEC/TS 61851-3-2:2023 was approved by
CENELEC as a European Technical Specification without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60309 series NOTE Approved as EN IEC 60309 series
IEC 60364-7-722:2018 NOTE Approved as HD 60364-7-722:2018
IEC 60990:2016 NOTE Approved as EN 60990:2016 (not modified)
ISO 18246:2023 NOTE Approved as EN ISO 18246:2023 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60038 - IEC standard voltages EN 60038 -
IEC 60335-1 2020 Household and similar electrical appliances - -
- Safety - Part 1: General requirements
IEC 60335-2-29 2016 Household and similar electrical appliances EN 60335-2-29 2021
(mod) - Safety - Part 2-29: Particular requirements
for battery chargers
+ A1 2019 + A1 2021
IEC 60529 - Degrees of protection provided by - -
enclosures (IP Code)
IEC/TS 61851-3-1 2023 Electric vehicles conductive charging - -
system - Part 3-1: DC EV supply equipment
where protection relies on double or
reinforced insulation - General rules and
requirements for stationary equipment
IEC/TS 62196-4 2022 Plugs, socket-outlets, vehicle connectors - -
and vehicle inlets - Conductive charging of
electric vehicles - Part 4: Dimensional
compatibility and interchangeability
requirements for DC pin and contact-tube
accessories for Class II or Class III
applications
CiA 454-12 - CANopen application profile for energy - -
management systems - Part 12: Gateway
unit
Under preparation.
IEC TS 61851-3-2 ®
Edition 1.0 2023-07
TECHNICAL
SPECIFICATION
Electric vehicle conductive charging system –

Part 3-2: DC EV supply equipment where protection relies on double or

reinforced insulation – Particular requirements for portable and mobile

equipment
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS  43.120 ISBN 978-2-8322-7085-1

– 2 – IEC TS 61851-3-2:2023 © IEC 2023
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 8
3 Terms, definitions, symbols and abbreviated terms . 8
3.1 Terms and definitions . 8
3.2 Symbols and abbreviated terms . 9
4 General requirements . 9
5 Classification . 10
6 Requirements for voltage converter units (VCUs) . 10
6.1 General . 10
6.2 Rated voltages and currents . 10
6.3 Requirement for AC/DC VCU for portable and mobile DRI EV supply
equipment . 10
6.4 Built-in DC/DC VCU for battery systems . 10
6.4.1 Built-in DC/DC VCU for battery systems (only AUX supply circuit) . 10
6.4.2 Built-in DC/DC VCU for removable battery systems (IEC PAS 62840-3). 11
7 Marking and instructions . 11
8 Protection against access to live parts . 11
9 Starting of motor-operated appliances . 12
10 Power input and current . 12
11 Heating . 12
12 Void . 12
13 Leakage current and electric strength at operating temperature . 12
14 Transient overvoltages . 12
15 Moisture resistance . 12
16 Leakage current and electric strength . 13
17 Overload protection of transformers and associated circuits . 13
18 Endurance . 13
19 Abnormal operation . 13
20 Stability and mechanical hazards . 13
21 Mechanical strength . 13
22 Construction . 13
23 Internal wiring . 14
24 Components . 14
25 Supply connection and external flexible cords . 14
26 Terminals for external conductors . 15
27 Provision for earthing . 15
28 Screws and connections . 15
29 Clearances, creepage distances and solid insulation . 15
30 Resistance to heat and fire . 15
31 Resistance to rusting . 16
32 Radiation, toxicity and similar hazards . 16

IEC TS 61851-3-2:2023 © IEC 2023 – 3 –
Annexes . 17
Annex AA (normative) Supply systems circuit diagrams . 18
AA.1 Standard supply systems circuit diagrams using NFC . 18
AA.1.1 General . 18
AA.1.2 EV supply system configuration type C, case A, accessories 4-II . 18
AA.1.3 EV supply system configuration type B, case B portable or mobile DRI
EV supply equipment, accessories 4-II . 20
AA.1.4 EV supply system configuration type D, accessories 4-II . 20
AA.2 EV supply system configuration type B, case B, coupler 4-I and 4-III . 21
AA.3 EV supply system conversion device using NFC . 22
AA.3.1 EV supply system configuration type C, case A, type 4-II, EV supply
system conversion device . 22
AA.3.2 EV supply system configuration type C, case B, accessories 4-II, EV

supply system conversion device . 22
AA.4 EV supply system conversion device configuration type B, case B, type 4-I
and 4-III . 23
Annex BB (informative
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.